Search Documents

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By E. D. Gardner

Humphreys Gold Corporation of Denver, Colo., was conducting a successful placer operation in 1936 on North Clear Creek about 6 miles below Blackhawk in Gilpin County, Colo. About 3,000 cubic yards of gold-bearing gravel are dug daily (September. 1936) by two draglines and a power shovel. The gravel is screened in a portable washing plant; the trommel oversize is discarded, and the undersize is pumped to a gold-saving plant. The gold is caught in riffles in sluice boxes. The total cost of mining is about 20 cents per cubic yard. The mine is in a narrow canyon at an altitude of 7,200 feet. The Blackhawk-Central City branch of the Colorado & Southern RR. runs over the property. Freight platforms for receiving supplies were moved as the workings advanced. The workmen reached the mine on a speeder that ran on the railroad tracks from a point on the automobile highway (U. S. 40) on Clear Creek near the bottom of Floyd Hill, about 5 miles distant. The mine is 36 miles by road and speeder, or 30 miles by rail, from Denver.

Jan 1, 1937

By A. M. Cummings

During August 1943, the Bureau of Mines undertook sampling and measuring of the Kennedy zinc tailing pile near Hazel Green, Lafayette County, south-western Wisconsin, as part of a general investigation of this lead-and zinc-producing area at a time when it was extremely important to increase the production of metals for the Nation's War program. The tailing pile was the residue from old jigging plants that treated ore from the Kennedy mine, one of the oldest and. largest mines in the district. Because retreatment of tailing by modern milling methods was proving economically successful at other sites in the southwestern Wisconsin field, the Bureau?s investigation was designed to assist the potential operators in evaluating the feasibility of a retreatment operation at this site. The study involved measurement of the tailing pile and sampling by means of auger to determine the average metal content within the narrowest possible limits. A total of 46 auger holes ranging in depths up to 40 feet and aggregating 886.5 feet of bore were drilled in the tailing pile, and weighted samples from each hole were analyzed and averaged to determine the zinc and iron content of the tailing.

Jan 1, 1949

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By E. J. Ostrowski

The Bureau of Mines experimental blast furnace, Bruceton, Pa., was operated to determine the feasibility of replacing part of the burden coke requirements with solid fuels injected directly into the smelting zone. This report describes preliminary experiments and information resulting from such an interchange. These experiments were made on an all-sinter burden, using two parts sinter to one part fuel. Anthracite fines were injected intermittently into the smelting zone of the furnace by compressed air through auxiliary tuyeres. The interval between injection periods ranged from 5 to 15 minutes. A maximum of 28 percent of the stock column coke bur-den was replaced. This percentage replacement caused furnace malfunction, but the overall percentage of these experiments indicated that 20 to 24 percent of the coke requirements could be replaced in this way. The metallurgical coke consumption was decreased by as much as 377 pounds (25.3 percent) per ton of pig metal produced. Buckwheat anthracite No.4 was used in this experiment; however, such solids as bituminous coal or coke fines also could be used. The frequency as well as the quantity of solid fuel injected has a direct bearing on furnace performance.

Jan 1, 1960

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By R. R. Brandenthaler

A series of open-flow tests was conducted in the Chickasha gas field, Grady County, Oklahoma, during June, 1927, under the direction of the U. S. Bureau of Mines and at the request of the Oklahoma Corporation Commission. The purpose of these teats was to determine whether or not any differences existed in the open-flow volume of a gas well when taken through well-head nipples of different diameters, and further, to establish if possible a relationship between open-flow volumes taken through well-head nipples of various diameters. The open flow of a well is the volume or quantity of gas, measured under standard conditions, that a well will produce when open to the atmosphere. There are several methods used for determining the open flow of wells; some of the methods are more suitable under certain conditions than others. The Pitot tube method is the simplest, is applicable to almost any condition, and is the one most commonly used. In the tests described in this paper no attempt was made to compare the Pitot tube method with the minute pressure measurement method or the orifice measurement method.5

Jan 1, 1928

By P. W. Jeran, C. M. McCulloch, Maurice Deul

The natural vertical fracture sys tem in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north- western West Virginia to N 57° W in southwestern Pennsylvania ; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures . Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the operational characteristics of spliced portable power cables. This research had a dual purpose: (1) to determine the thermal and mechanical performance of repaired trailing cables and compare them with undamaged cables and (2) to gauge the impact of long-term, localized heating on the insulating and jacketing materials contained in cable splice kits accepted or approved by the Mine Safety and Health Administration. The ranges of splice joint resistance and tensile breaking strength were determined from laboratory measurements. The choice of crimping tools affected the strength of the splice under tension. Thermal profiles of energized spliced cables were constructed, which showed that spliced conductor joints operated 5 to 20°C hotter than the intact cable at rated currents. Accelerated life tests of thermally aged samples of splice kit insulation and jacket materials confirmed a deficiency in the thermal rating of the insulating tape. The recommendations in this report may be utilized to revise splice kit design, splice kit approval criteria, and trailing cable loading guidelines. Characterizing the thermal operating limits of spliced trailing cables may help to minimize the associated risks from explosions, fires, personnel burns, and shock.

Jan 1, 2010

By W. H. Eddy

The Bureau of Mines conducted laboratory batch-and small-scale continuous flotation processing tests on waste granite fines from Georgia, to determine the feasibility of recovering usable feldspar and quartz products by flotation. Two flotation methods were utilized for the removal of biotite and other iron-bearing minerals: One was in an acid-cationic circuit, and the other in an alkaline-anionic-cationic circuit. Feldspar was recovered using an acid-cationic method. To produce commercial-grade feldspar and quartz products it was necessary to employ either two sequential froth flotation circuits or one froth flotation circuit supplemented by wet-magnetic separation techniques to remove iron contaminants. Continuous flotation processing yielded a commercial-grade feldspar concentrate containing, in percent, 3.8 Na20, 5.4 K20, and 1.10 CaO, with recoveries of 77.8, 70.3, and 64.4, respectively. The feldspar tailing was high-quality glass sand containing 98.2 percent SiO2 and 0.024 percent Fe2O3. About 42 percent of the quartz was recovered at glass sand specifications. An effective separation of, potash feldspar from the bulk feldspar concentrate was achieved by batch flotation in a mineral separation cell.

Jan 1, 1974

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By W. A. Selvig

The experiments described herein were made at the request of Committee D-5, on Coal and Coke, American is n Society for Testing Materials, in order to obtain data as to the probable contamination of laboratory samples of coke Then pulverized to pass a No. 63 sieve of tine U. S. Standard Sieve Series2 by methods other than by ball-mills or hard-steel diamond mortars, which methods are specified-in the standard methods of that Society.3 After pulverizing, representative samples were analyzed by the Bureau of Mines at Pittsburgh for ash content to detect any contamination of the samples by the pulverizing apparatus. Preparation of Core Samples for Tests. Two samples of 48-hour beehive coke (Continental and Leisenring) made from Pittsburgh coal were selected for the tests. These cokes were crushed approximately to No. 10 sieve size, by first passing through a jaw crusher and then through a, roll crusher. The crushed coke was then carefully mixed and riffled into portions of about 800 grams each, and sent to three cooperating laboratories for grinding, through a No. 60 sieve. Size tests on these samples shoved the fineness to be as follows: [ ]

Jan 1, 1925

The U.S. Environmental Protection Agency (EPA) and the U.S. Congress are presently considering several approaches aimed at reducing the amount of lead in the environment and society's exposure to lead. One approach is to tax domestic primary lead production or consumption. Objective To assist the Congress and the EPA in their decisionmaking, a study was initiated by the U.S. Bureau of Mines, which assesses the minerals related implications of a tax on U.S. primary lead production and primary lead imports. This investigation analyzes the impacts of a primary lead lax on: (1) domestic primary lead production, (2) domestic lead coproduct and byproduct production (including bismuth, cadmium, germanium, indium, silver, and zinc production), (3) domestic secondary lead production, (4) lead imports, (5) domestic lead recycling activity, and (6) the U.S. lead price. Study Findings Domestic Primary Lead and Primary Lead Coproduct and Byproduct Production. A quantitative analysis based on the application of the Bureau's Supply Availability System (SAM) has been conducted to determine the impacts on domestic primary lead and primary lead coproduct and byproduct production from domestic lead source material for a range of taxes.

Jan 1, 1992

By Rollien R. Wells

A REPORT of technological advancements restricted to a specific 12-month period is impractical. Inherent in the nature and development of technology is the element of time; rarely can a new process or product be attributed to a particular year. An overall picture of general trends and pattern changes, however, is indicative of technological growth. This paper presents selected observations and discussions of current metallurgical research and practices in an attempt to develop' such a picture. Of the estimated $16.5 billion spent for research and development in the United States in 1962, at least 80 percent was earmarked for the aircraft, electronics, chemical, and machinery industries. Much of the effort was of the end-use variety and was oriented closely to the national defense and aerospace programs. Only a small fraction of the total research money was directed to studies of the utilization and improvement of metals. Even if the investigations in allied fields such as solid state physics are included, the total research expenditure for metal and mineral materials barely reached $500 million. An additional $200 million was spent by industry and government for development of minerals recovery and processing methods.

Jan 1, 1963

By T. A. Sullivan

Research undertaken by the Bureau of Mines in 1938 has resulted in the development of titanium from a laboratory curiosity to a commercial metal. Along with processes for producing the metal, it was necessary for the Bureau to develop methods for analyzing the metal, raw materials, and intermediate products. Some of the methods developed have been published.3 4 5/ General Services Administration (GSA) was responsible for purchasing titanium metal under Defense Production Act contracts with commercial producers. GSA designated the Federal Bureau of Mines to analyze this metal and establish its compliance with Government specifications. A substantial quantity of tin was found in some of the samples analyzed, and in July 1957 tin was added to the list of impurity elements to be determined. The specifications limited the amount of tin in titanium sponge to a maximum of 0.10 percent. A program was immediately initiated to investigate methods and techniques for determining tin in the range of 0 to 1.0 percent. A method accurate at the 0.10 percent level was necessary, as this level was the critical range for acceptance or rejection of the metal.

Jan 1, 1960

By W. A. Selvig

"INTRODUCTION In 1942, Lowry and Junge 3/ reported the results of a statistical study of errors for the proximate and ultimate analysis of coal and coke when made according to the standard Methods of Laboratory Sampling and Analysis of Coal and Coke (D271-42) 4/ of the American Society for Testing Materials. Some of the laboratories that cooperated in the investigation reported difficulty with determination of the volatile matter of anthracite and low-temperature coke. The small number of analyses reported for these particular fuels was considered inadequate to justify definite conclusions regarding the precision of this determination.The investigation described in this report was made at the request of Committee D-5 on Coal and Coke, A.S.T.M. (A. C. Fieldner, chairman), to secure additional information regarding the errors of the volatile matter determination for anthracite, low-temperature coke, and subbituminous coal; the last fuel also gives trouble in this determination, The committee has recognized that the allowable differences between duplicate determinations of volatile matter for these fuels as given in the standard methods are perhaps too stringent and may require revision."

Dec 1, 1943