Search Documents

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Ronald P. Hollenbeck

Samples of clays, shales, and slates from 29 locations in the Appalachian Region of Alabama and Georgia were tested and evaluated to determine their suitability as raw material for the manufacture of lightweight aggregate by the rotary-kiln method. Samples from 11 locations in Alabama (one each in Etowah, Lawrence, and Morgan Counties and two each in Colbert, Cullman, Tuscaloosa, and Walker Counties) and one location in Walker County; Ga., produced satisfactory lightweight aggregate.

Jan 1, 1969

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By Erie C. Donaldson

Gas-displacement tests were made in Berea Sandstone and Arbuckle Lime-stone cores to determine the relative permeabilities to gas, oil, and water for two-and three-phase dynamic systems. Three-phase relative permeabilities were obtained by displacing oil and water from the core with gas and measuring the flow rates of the three fluids simultaneously. It was found that relative permeabilities to fluids in a porous medium are affected by the saturation distributions of other fluids in the medium as well as by their own saturation distributions.

Jan 1, 1966

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By R. E. Heithecker

[The principle of determining volumes of liquid by alternately drawing in and discharging given quantities of the fluid from a confined space or compartment of known volume and mechanically counting the number of displacements is well established. This is true particularly in water measurement. For several years, oil meters employing the same basic principle have beer, used for gaging oil production from individual wells, groups of wells, and in some areas for metering the entire production from a property. Especially in areas where there is town-lot drilling and space for tankage in at a premium, oil meter have been used successfully to gage the oil. This facility has obviated the necessity of installing gage tanks. Oil meters also have been used in pip-line and refinery operations and in loading tankers. Present knowledge of the subject shows that positive-displacement oil meters can be used for measuring crude oil in the field and elsewhere, provided the meter-counter mechanism is in proper adjustment and the oil has been studied sufficiently to determine the proper factor to be applied to the volume as registered by the meter, making possible the adjustment for the shrinkage of the oil caused by liberation of gas from solution.]

Jan 1, 1938

By Arthur B. Campbell

This Bureau of Mines report describes a method that utilizes a computer program to evaluate integral Gaussian profiles of atomic concentration versus depth in a solid. The specific use illustrated involves profiling ion- implanted metals using proton-induced X-ray emission (PIXE) analysis and ion sputtering (IS) for sectioning

Jan 1, 1979

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By J. H. Holden

The Federal Bureau of Mines is doing research and development work on a pressure-gasification pilot plant for producing synthesis gas directly from pulverized coal, oxygen, and steam. A pressure-gasification pilot plant has been constructed, and an investigation was made with the following basic objectives: 1. Determining the effect of varying pressure (75, 100, 150, and 300 p.s.i.g.), coal rate (400, 700, and 1,000 pounds per hour), and oxygen-to-coal ratio (8 to 11 std, c,f. per pound), on percentage of carbon gasified, oxygen and coal requirements per unit of CO + H2 produced, exit-gas temperature, and heat loss. The steam-to-coal ratio was maintained at approximately 0.3 pound per pound. 2. Development of a stabilized gasification zone or reaction space. 3. Improvement in operability of the pilot plant.

Jan 1, 1960

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By Willard L. Hunter

The smelting of tin slags was undertaken at the Bureau of Mines Albany Metallurgy Research Center (AMRC) to produce crude columbium-tantalum ferro-alloy as a unit operation in the production of pure columbium and tantalum oxides or chlorides. Columbium and tantalum-rich alloy was prepared during short unrelated campaigns over a total period of 12 years. Tin slags from Malaya and the Congo (Geomines) were smelted. These slags were reduced by carbon in a small, single-phase, steel-making furnace} a larger three-phase, steelmaking furnace, and a three-phase, submerged-arc furnace, In all cases depleted slags were fluid and easily tapped from the furnace. However, unless diluted by iron additions, the metal product was a viscous, high-melting, heterogeneous mixture that could be removed from the furnace only by hand rabbling.

Jan 1, 1966

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leaching cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric aoid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to extract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of obtaining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present.

Jan 1, 1931

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leach¬ing cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric acid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to ex¬tract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of ob¬taining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present. Former papers have considered the rate of dissolution of azurite, malachite, tenorite, chrysocolla, cuprite, chalcocite, boruite, and covellite in common leaching solvents. A paper soon to be written will consider some of the less important copper minerals. The present paper considers the rate of dissolution of copper from ores of the Southwest in sulphuric acid of varying strength and the ratio of sulphuric acid consumed to copper dis¬solved. In this study two ores containing the copper principally in an oxidized condition were used. A study of other ores, especially those containing high percentages of sulphide copper minerals, would be desirable, but since consumption of acid has paramount interest,

Jan 1, 1931

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By J. E. Tiffany, N. A. Tolch

The Pittsburgh Experiment Station has made a survey of the properties and characteristics of the brands of fuse manufactured in the United States ; 25 samples were procured from 4 manufacturers representing the different brands offered on the market when the investigation was begun . It is believed that the field was completely covered except for special fuse made to order for a particular job .

Jun 1, 1934