Search Documents

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By Thomas C. Atchison, Joseph M. Pugliese

Six explosives were compared by measuring their strain- producing abilities in limestone . Peak strain , e , varied with scaled distance , R/Ro , according to the following equation : € = Kc (R /R 。)- ". The distance exponent , n , was a constant of the rock and did not depend upon explosive . The strain intercept , Ke , increased with increasing detonation pressure of the explosive . The strain intercept also depended upon the explosive- to - rock impedance ratio . For impedance ratios from 0.53 to 1.38 , the strain intercept was approximately proportional to the medium stress , Pn , as calculated from the explosive detonation pressure , P , and the explosive - torock impedence ratio , Z , by the simple elastic theory relation : P = 2P / ( 1 + Z ) . PD However , the data indicated that , at lower values of impedance ratio , the strain intercept is relatively larger than would be expected from the simple elastic theory . The results presented provide a simple method for predicting the relative effectiveness of different explosives in breaking limestone from the detonation pressures and characteristic impedances of the explosives .

Jan 1, 1964

By James A. Browning

Conventional flame channelling operates continuously at over 120 db --flame-drill channelling at a maximum of 95 db. The latter process was developed under this program. Individual drill holes are spaced to leave narrow rock webs. Sound and dust passing from the hole are effectively treated by a muffler and water injection.

Jan 1, 1980

By Z. Zhiqun, V. A. Marple, B. Y. H. Liu

"IntroductionIt is commonly understood that aerosol particles may be injurious to human health if they are of a size that enables them to enter the respiratory tract. Coal Workers' Pneumoconiosis (CWP) is one disease known to be caused by coal mining related particles.The location in the respiratory tract where the particles are deposited is primarily a function of the equivalent aerodynamic diameter (EAD) of the particle. The equivalent aerodynamic diameter is the diameter of a spherical particle with a density of 1.0 gm/cm3 with the same falling speed as the particle in question. For a spherical particle the calculation is rather simple in that the equivalent aerodynamic diameter is simply the diameter of the particle in question multiplied by the square root of the density of the particle. For irregularly shaped particles, such as coal particles, there is no simple way to make the EAD calculation. For example, Figure 1 is only one of an infinite variety of particle shapes that can be found in practice and the aerodynamic size of this particle and, therefore, its deposition location in the respiratory tract would be nearly impos-sible to estimate accurately.The normal method for determining the aerodynamic diameter of particles has been to experimentally measure the size of the particles in a settling chamber or with an inertial classifier such as an impactor, cyclone or a centrifuge, since inertial classifiers have the property of classifying the particles according to their aerodynamic diameters."") However, these devices can only give limited information on the EAD of a single particle with a specific shape. Impactors and cyclones, for example, collect particles in size ranges and not at a specific size, so the determination of the EAD of a specific particle is not possible. A centrifuge, on the other hand, can measure the EAD of a specific particle but the equipment is costly and procedure laborious, and it may not be possible to disperse a particle of a specific shape into the centrifuge. The centrifuge can be used to determine the EAD of clusters of spheres in various arrays, but introducing particles of a specific irregular shape may not be feasible. Furthermore, the EAD is a function of the orientation of an irregularly shaped particle and the orientation of a particle in an inertial classifier is unknown. The orientation may also vary as the particle passes through the classifier.Because of the difficulty in determining the EAD of an irregularly shaped particle, we have undertaken a program to apply theoretical numerical methods to calculate the EAD of any shape particle. In our laboratory we have, for some time, been using numerical methods to determine the flow field of air within instruments such as impactors, (2) inlets, (3) and virtual impactors (4) Recently, this technique has been expanded into the three-dimensional regime, and the flow fields and particle motion characteristics within cyclones (5) and glove boxes have been studied. We have now begun to use these numerical three-dimensional flow programs to study the flow field around irregularly shaped particles to determine their drag coefficients, falling speed, and thus, their EAD."

Mar 1, 1989

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.070 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70° C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 to 1,000 ms gave the following results: Ag concentrations decreased from 34 to 0.1µg/mL, Au concentrations decreased from 54 to 0.2 µg/mL, and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 2010

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 8,445 acres of the 20,650-acre Tunnison Mountain Wilderness Study Area in order to evaluate its identified mi nerd 1 resources. The study area is located in Lassen County, CA, about 8 miles northeast from Susanville. No mineral resources were identified in the study area based on literature, field observations, and sample results. No mines were operating in or near the study area in 1985, and no mines, prospects, or claims have been located in or within 1 mi le of the study area. The study area is underlain by Pliocene and Pleistocene volcanic units composed of basalt, andesite, rhyolite, and some pyroclastics. No metallic and only nonmetallic commodities are present in the study area. These included stone and sand and gravel. Although substantial volumes of basalt and andesite (stone) occur within the study area, no identified resources of these commodities were delineated. Sand and gravel is not economic because of small occurrence size and lack of local markets.

Jan 1, 1987

By Paul Hatmaker

Pumice and pumicite are siliceous volcanic substances quite similar in chemical composition , but somewhat different in physical properties , manner of formation , and mode of occurrence . Production in the United States has increased from 23,271 tons valued at $ 94,943 in 1910 , to 56,843 tons valued at $336,099 in 1930. Both pumice and pumicite are included in these figures as it has been impractical to collect statistical data on the separate commodities .

Mar 1, 1932

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of seven manganese-ore samples. Six of the seven samples were submitted through the Mining Division, and 1 from Mexico was submitted by H. A. Doerner, formerly chief metallurgist, Region III. These investigations were made to assist development of mineral resources and particularly to aid economical exploitation of marginal or complex ores, from which strategic or critical minerals may be recovered.

Jan 1, 1953

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1362 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By N. A. C. Smith

This report on the physical and chemical properties of typical crude oils of southern Louisiana and southern Texas is the seventh in a series of preliminary chapters of a bulletin covering the producing districts of the United States. Preceding reports* may be obtained from the Bureau of Mines on request. The details of the methods used in this survey in collecting samples and making laboratory tests have been discussed in the first three papers. A method of summarizing and interpreting the laboratory data has also been given, but most of the crudes included in the present report differ so radically from those previously reported, that it has been found advantageous to adopt a somewhat different method in making summaries. This method is described in detail later. If any errors or omissions are noted by readers, it is hoped that these will be brought to the attention of the Bureau of Mines, for correction before the appearance of the final bulletin.

Jan 1, 1922

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By Leland H. Johnson, D. O. Kennedy, John Hyvarenen

"SUMMARYA chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost has been compiled. Many accidents were described in more detail because of their unusual features. Tables have been included to indicate the number of major disasters and fatalities by the principal product mined, by State, and by 10-year intervals prior to 1945. The number of men employed to indicate man-hours exposed is unavailable; therefore, a true picture of disaster data by principal product mined, by State, and by 10-year intervals is not possible. However, the data are presented to indicate the causes of major accidents and bring to the attention of those affiliated with metal and nonmetal mines and quarries the hazards involved and lessons that can be practiced to keep such accidents at a minimum.INTRODUCTIONThe Bureau of Mines was requested to compile a chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost. Data have been assembled on accidents from all causes in these mines and quarries from the earliest available information (describ¬ing an underground mine fire in Nevada in 1869) to the last reported major accident (a fire at a company-owned bunkhouse in Arizona in 1945).The accounts of the accidents were taken from articles in the technical press and from published and unpublished reports of the Bureau of Mines. Many of the accidents have been selected for more detailed descriptions because of the unique circumstances and to show the variety of dangers involved.Tables are included to indicate the number of major accidents, with resultant fatalities, by the principal metal and nonmetal producing groups, by State, and by 10-year intervals previous to 1945. The interval 1869-1875 does not cover a 10-year span because of incomplete records previous to 1869.ACKNOWLEDGMENTSThe information contained in this report was obtained from the Engineering and Mining Journal from 1874 to 1947, the Mining and Scientific Press from 1908 through 1922, from various published and unpublished reports of the Bureau of Mines and from reports by State departments of mines. Daniel Harrington, retired chief of the Health and Safety Division; E. H. Denny, supervising engineer, District H; R. M. Loucks, mining engineer; and other engineers of the Division contributed much valuable information and assisted materially in the study."

Apr 1, 1949

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By Abrasive Materials

Table 1.-Salient abrasive statistics in the United States [ ]

Jan 1, 1967