Search Documents

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970’s, only the sub-aeration mechanical cells were dominant. Since the 1980’s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs."

Jan 1, 2003

By Anuj Narang

Large-scale separation or flotation cells, used in the primary extraction in the oil sands industry, are integral parts of the overall process of bitumen extraction. Good regulation of the interface level between the bitumen froth and the middlings in these cells can result in a significant improvement in bitumen recovery and throughput, and heavily influence process economics. Automatic control of such industrial processes presents challenges such as multi-phase flow dynamics, variable process gain and time delays, poor quality of measurements and significant disturbances. This paper details a case study application of development of multiple models of the dynamics of the interface level and the design of model predictive controllers (MPC) for a separation cell process. A Model predictive controller (MPC) using linear models is designed and implemented in real time on an industrial separation cell. The industrial implementation results show that the MPC scheme provides significant benefits over the current operations which use a PID controller. The benefits include significant reduction in the variance of the interface level resulting in higher bitumen recovery and smoother downstream operation plus energy savings due to reduced underflow pump speed.

Sep 1, 2012

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By ?. Kostadinov

Theoretical study of the behavior of grinding medium presented by TBP (tetraballpebs) was conducted by computer modeling of the position of grinding medium at different speeds and different drum fill factor. For the modeling were used known equations of motion derived for the ball load. Algorithm was created by SolidWorks software, allowing determination of center of gravity of the load in the mill and energy for grinding. These results were compared with similar results obtained by ball grinding medium. The capabilities of both grinding media are demonstrated by graphics under the following conditions: 1.Equal dimensions of the experimental model of the mill; 2.Equal mass of the grinding loads; 3.Comparison of grinding bodies with the same number, mass and density. Keywords: simulation, behavior, grinding medium, balls, tetraballpebs

Sep 1, 2012

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By A. Lane

Africa is ripe with opportunity for the mining industry. The continent has large, and relatively unexplored mineral deposits, and recent high economic growth rates have meaningfully improved the political, economic, and infrastructural environments. However, these opportunities are accompanied by significant risks, including resource nationalism, uncertain regulation, corruption, and continuing political instability (up to and including war). Forward-looking companies actively manage these risks by creating a sense of shared purpose with the countries and communities that own the resources, using tools such as stakeholder analysis, local narratives, scenario planning, and constituency engagement. They also measure socio-economic impact to insure the creation and demonstration of shared value.

Sep 1, 2012

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012

By Kaustubh Joshi, Pradip, Beena Rai, Kesri L. Menaria, Venugopal Tammishetti

"Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. High alumina is deleterious for the performance of both blast furnace as well as sintering plants. Slimes generally contain 5 - 10% alumina, and hence despite assaying as high as 60% Fe, those are dumped in tailing ponds. The slimes are typically less than 37 microns. Selective flocculation of iron ore slimes using highly selective reagents is thus an option worth exploring. Our research is directed at employing state-of-the-art molecular modeling techniques for the selection/design of selective reagents for this separation. We have earlier reported our results on starch as a selective flocculant for iron ore slimes. In this paper, we present our results on the selective dispersion-flocculation of natural iron ore slimes using guar gum flocculant. With careful selection of various process parameters such as flocculant dosage, dispersant dosage, pH and settling time, we were able to obtain a concentrate assaying >66% Fe and <3.5% Al2O3 with an yield of 65 to 68% (recovery of iron values more than 70%) from a natural iron ore slime sample assaying 58% Fe and 7% Al2O3."

Jan 1, 2014

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By L. S. Gertsch

The production of minerals for human use at locations other than the Earth is expected to ?advance ? human prosperity in ? ways that [do] not compromise the potential prosperity and quality of life of future generations? (Brundtland, 1987); in other words, sustainably. This paper examines the interaction of extra-terrestrial mineral production (ETMP) with the following sustainability imperatives: ? The sustainability of human activities on Earth; ? The sustainability of human activities elsewhere; ? Human survival in general, the ultimate sustainability goal. Some of the consequences of mineral production on Earth are widely considered to decrease the future prosperity and quality of human life. Examples include noxious by-products or wastes and unsettling economic up- and downswings. Moving mineral production activities to extra-terrestrial locations, where appropriate, will decrease many of its deleterious effects. Terrestrial mineral production presently is decreasing in some countries and increasing in others, moving from the cheaper and easier ores to more expensive, difficult materials. When the full costs of maintaining the terrestrial environment in a sustainable manner are included, total mineral pro-duction costs must increase. The cost of extracting mineral products from extra-terrestrial sources will be substantially higher, especially in the initial phases, but as the full costs of terrestrial production increase, at some point in the future (different points for different minerals), the curves will cross (Fig.1). This will occur at different points for different materials, a process whose prediction will be complicated by substitution of cheaper materials for some uses as prices of the original material rise. In summary, mineral products from extra-terrestrial sources will tend to increase the sustainability of human civilization, once steady state has been reached.

Jan 1, 2014

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Chromite ore is an indispensable raw material in the manufacture of ferro-chrome and charge-chrome, which are used for the production of stainless and other alloy steels. The demand for chromite ore is ever increasing because of increasing consumption of these steels. Keeping this in view, Tata Steel is keen to recover values from fines and wastes, and also to produce value added products from their captive chromite mines and its processing plants.Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In many places, in India and abroad, mined non-marketable off-grade and low grade chromite ores are upgraded by using either simple classification techniques like screw classification, hydrosizing, hydrocycloning or conventional gravity concentration processes such as Heavy media separation, Jigging, Spiraling, Tabling etc.At Tata Steel, the ferruginous type ores are treated in Chrome Ore Beneficiation (COB) Plant that comprises: a crushing and grinding circuit; a classification circuit using hydrocyclones; and a beneficiation circuit using 4 stage spirals in the coarse circuit (-0.5+0.1 mm) and 3 stage spirals & tables in the fine circuit (-0.1+0.038 mm). In this process, 3 types of tailings are being generated and together analyses about 17 % Cr2O3, which is high. From the present operation the chromite recovery is around 70% and could not produce coarse concentrates (+0.5 mm size). Whereas the siliceous type ore is treated in the Lumpy Ore Processing (LOP) plant, consisting of crushing-washing & classification-hand sorting operations, to produce marketable grade lumpy ore and –10 mm de-slimed fines. These fines are intermittently treated in the COB plant. The higher silica content (greater than 1%) and low Cr/Fe ratio (less than 2.8) are the problems with these concentrates."

Jan 1, 2003

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"This work presents the results of the development of a flowchart for the processing of copper production dusts resulting in the production of of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.Dust having the following composition (wt. %): Pb 39.3, Zn 6.5, Cu 5.5, Stotal 10.8, As 1.05, SiO2 0.6, Cd 0.8, Bi 0.04, Ag 0.02, Re 0.03 was used in the work. Chemical and X-ray analyses indicated that lead, zinc and copper are generally present in dusts in the form of sulfates, various amounts of oxides, sulfides, silicates; sulfur (according to chemical analysis data) is present in the form of sulfates (~ 90%) and in the form of sulfides (~ 10%).Studies have been made on two-stage stripping of copper production dusts containing lead, zinc, copper, cadmium, rhenium in the form of various compounds, at first with soda solution, then with nitric acid solution. It has been indicated that the combination of the operations allows the recovery of 98% rhenium, 82% lead, 92% copper, and 96% zinc and cadmium each in the solution. Furthermore, at the stage of dust leaching with soda, 80% of rhenium and 0.01% of nonferrous metals each are recovered in the solution. Remaining quantities of all metals are recovered in nitric acid solution up to maximum values. Such behaviour of metals is caused by metal phase content in dusts and properties being formed during leaching of compounds. At the stage of dust leaching with soda solutions, carbonates with various compositions are formed due to the exchange reaction between nonferrous metal sulfates and sodium carbonate. The conversion of PbSO4 into PbCO3 is apparently occurs in the solid phase and the conversion of readily watersoluble zinc, copper, and cadmium sulfates into that of carbonate salts occurs in the liquid phase. Rhenium passes into solution due to the presence of rhenium greater quantity in dust in the form of readily soluble perrhenate. Some portion of the perrhenate is, probable, blocked by lead sulfate and liberated in the conversion of PbSO4 into PbCO3."

Jan 1, 2003

By R. C. Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of refractory processes past and present and the location of currently operating plants. Some discussion on the challenges that face the refractory gold industry will also be provided. Keywords: refractory gold treatment, flotation, roasting, pressure oxidation, bacterial oxidation, preg-robbing gold ores, fine grinding.

Sep 1, 2012

By Z. H. Li

In connection with the features of characteristic waste water (containing cyanogen, arsenic and heavy metal) pollutants discharged by gold industry as well as the environmental features at the location of gold production enterprises, this paper briefly described the traditional method of treatment, and focused on the argument for technologies of clean production, advanced treatment and process control technology. Moreover, it clarified the future policies and development trend for treatment on characteristic waste water from gold industry.

Jan 1, 2014

By J. P. Dai

The Fankou Mine in Guangdong province, China, processes a polymetallic ore containing averagely 4.2% Pb, 8.5% Zn, and 90 g/t Ag. The main metal minerals including sphalerite, galena and pyrite are very finely disseminated and unevenly occurred in the ore, making it difficult to liberate them from each other. This paper presents the processing technology of the Fankou plant and the characteristic features of the novel technology applied.

Jan 1, 2014

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012