Search Documents

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By A. V. Faiberg

Currently, the interest to conditioning of cyanide-bearing recycled solutions with high-grade of base metals, in particular, copper has significantly grown. This can be explained by two major factors. Firstly, there are strict regulations on cyanides amount in tails and higher cost of detoxification processes. This problem can be easily solved during the ore treatment using the conditioning of solutions and water recycling. Secondly, the presence of other metals minerals which react with cyanide during gold leaching resulting in high cyanide consumption. The presence of copper is a major problem. Many copper minerals react with cyanide with the formation of cyanide complexes-Cu(CN)2-, Cu(CN)32- and Cu(CN)43-. One mole of copper consumes 2-4 moles of free cyanide. Availability of cyanide-soluble copper minerals has deleterious effect on gold leaching (gold recovery, cyanide consumption, tails detoxification, efficiency of gold elution and electrowinning). The precipitation of copper from the solutions improves gold recovery by CIL. The removal and recycling of cyanide allowed the reduction of cyanide addition to the process. The recycling of spent cyanide-bearing solutions based on the removal of copper and the return of cyanide bound in complex compounds for leaching process is an optimal way of solving the problem of gold-bearing copper ores treatment. By using the technology, an adverse impact onto gold recovery process is eliminated and at the same time reducing the cyanide consumption. Today, processes and methods of high-grade copper leaching solutions conditioning before and after gold recovery have been developed, which combine two ways of copper recovery: as a saleable product and cyanide to recover gold and reduce total operating costs. They are Cutech, MNR, SART, Cyanomet, AuGment, Vitrokele, Hannah and Cyanisorb. At the same time, these technologies have not been studied enough and described in literature. Data on parameters and operating conditions as well as introduction is not available. The conditioning technology of recycled solutions developed by IRGIREDMET JSC allows copper to be recovered as high quality concentrate and at the same time free cyanide regeneration in the recycled solution which is amenable to gold leaching. This technology was commercialized at a mine in Kazakhstan in 2008. The removal and recycling of cyanide does not require additional cyanide and is cost-effective. More cost-efficiency is achievable through selling copper concentrates, closed water cycle without the detoxification of effluents and enhanced gold recovery by CIL and cathode quality.

Sep 1, 2012

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By T. Khonthu

The purpose of this investigation was to evaluate the relationship between different milling procedures, viz. a ball mill and an IsaMill respectively, and the flotation performance of the different mill products. Two ores were used, viz. a base metal sulphide (BMS) and a platinum group mineral (PGM) UG2 ore. Flotation was used as a diagnostic to investigate whether the different milling procedures may have different effects of the floatability of the particles. The present study is part of a research programme investigating this question using a wide range of comminutiondevices and procedures. Similar particle size fractions from the different milling procedures were used in the flotation tests. The particles were characterized in terms of particle size distribution, morphology (using scanning electron microscopy and image analysis software) and rheology tests. The results have shown that in general when comparing similar feeds to flotation in terms of equivalent particle size distributions as indicated by the d80 value, the ball mill generally yielded better recoveries and grades in the case of the BMS and lower chromite recoveries in the case of the UG2 ore compared to the IsaMill. No significant differences were observed in the morphological or rheological characteristics of the particles subjected to the different milling procedures. Although the results appear to indicate that IsaMilling is less advantageous than ball milling in terms of the flotation performance for the two ores studied it should be emphasized that these results do not take into account the relative advantage which IsaMilling has over ball milling in terms of direct and indirect energy consumption and GHG emissions nor, most importantly, does it consider the platinum group element recoveries in the case of the UG2 which may have increased significantly as a result of the finer grind which the IsaMill produces after 4 passes compared to the ball mill after 64 min. Such results which will be reported is due course may show that the greater liberation expected after IsaMilling of the PGMs outweighs any disadvantages indicated in this study.

Sep 1, 2012

By M. Blagojev, R. Tomanec

"Studies reported in this paper used polymetallic Pb-Zn-Sb-As-(Ag, Au) ore from Dražnja, Kosovo. The ore is comparatively rich in Zn (6.56%) and Pb (2.87%), but with high rates of Sb and As. Conventional lead and zinc concentration by flotation produced galena and sphalerite rich concentrate with high recovery, but with excessive As and Sb. After chemical analyses, which could not detect the reason for the excessive elements, ore minerals were identified under the ore microscope, their texture characterized, and degree of liberation of useful minerals was assessed. Microscopy of the mineral concentrates revealed complex intergrowths of galena and marmatite minerals mostly with sulphosalt minerals (boulangerite, jamesonite and bournonite) and also with arsenopyrite mainly responsible for the unsatisfactory quality of the concentrate. These complex sulphosalts, among other things have similar behaviour during the flotation concentration, and in spite of their interlocking with galena, therefore inadequate liberation, sulphosalts remain in the lead concentrate. Microscopic analyses indicated that a better galena concentration product is possible with a higher rate of mineral liberation, and then by selective floc flotation of some sulphosalt minerals. Purpose of this work was to show that only chemical analysis is not sufficient, according to that we solved the problem by precise mineral identification and time consuming mineral liberation measurements. INTRODUCTION The polymetallic Pb-Zn-Sb-As-(Ag, Au) ore body of Dražnja, Kosovo, fairly rich in Zn (6.56%) and Pb (2.87%) was repeatedly explored and once even worked. Mineralization at Draznja was primarily represented by sphalerite, galenite and marcasite/pirite. Some sections comprise massive sulphides, and others are lower grade zones of semi-massive sphalerite/galena or marcasite/pyrite dominant sulphides. The ore body II was formed in the southern gallery in the structure Çukë – Lajthishtë (with content of 3.16% Pb and 7.31% Zn). Pb-Zn ore with increased content of As, Sb sulphosalts is not rare phenomenon in the world. While previously treated as unprofitable, economical uninteresting ore, today with development processing and new reagents (organic, ecologic), are the topic of scientific papers. The examination of Pb-Zn ore with high content of sulphosalts we find in deposits as: The hydrothermal vein deposit of Harja in the Baia Mare area, contain a wide variety of sulphosalts [Cook, N. & Damian, G., 1997]; also the deposits Fankou Mine in Guangdong Province and the Dachang Mine in Guangxi Province, where the flotation concentration of galena and jamesonite takes place [Runqing Liu et al. 2015], [Zhang Ting, Qin Wen-Qing, 2015];. On a samples from Tibet in China flotation separation test of galena and jamesonite was conducted [Sun Wei, Han Haisheng, Tao Hongbiao, Liu Runqing, 2015]. According to history of investigation, the mineralized area of Dražnja has a long history of exploration and possible exploitation activities [Slowey, Galen, 2009]. Recent workings were carried out in three stages through the 20th century."

Jan 1, 2018

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014

By X. Q. Cao

As the second largest phosphate resource in the world, Chinese phosphate ores generally grades with low of P2O5. The presentation of beneficiation test on the low grade of phosphate rock in this paper may be used for a reference for development and utilization of the similar reserves. The ore is a marine sedimentary phosphate rock containing low grade of P2O5 and high content of MgO and R2O3; The banded structure shows its suitability for heavy medium separation. The laboratory heavy liquid testing results indicate that as specific gravity of the heavy liquid is 2.85 g/cm3, a rougher concentrate assaying 28.71% P2O5 could be obtained while the rougher tailings contain only 4.47% P2O5. When the combined process with heavy liquid separation followed by direct & re-verse flotation is employed to treat the feed containing 21.15% P2O5, 3.79% MgO, 1.86% Fe2O3, 3.66% Al2O3, 23.75% A.I, and specific gravity of heavy liquid is 2.84 g/cm3, the optimum mesh of grind is 67.5% minus 200 mesh, a phosphate concentrate contained 32.51% P2O5, 0.48% MgO, 0.81% Fe2O3, 1.69% Al2O3 can be produced at a yield of 55.24%. The concentrate P2O5 recovery is 85% with which quality comply with the Class A specifications for production of phosphate fertilizer.

Jan 1, 2014

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By Liu Fan, Shang Yanbo, Wang Zhongming

"Besides valuable metals of Cu, Sn, WO3, Zn, there are S, Ag, CaF2, In and so on in a complex ore deposit in south China (which belongs to Hu Nan Shizhuyuan Non-ferrous Metal Limited Liability). Although it proved reserve amounts to 3.5×107 ton, its crystal character limits its utilization in large-scale. It features complex relationships between valuable minerals, finest crystallized particle size, low-graded valuable metals (Cu 0.30%, Zn 0.5-0.7%, Sn 0.2%, W<0.1%). If only tungsten minerals are considered, it means WO3 grade is too low (the cut-off grade of WO3 is 0.1% in China). Only Cu and Sn minerals are recovered from 2006 and Cu recovery is less than 70%, Sn 15-20%. Other valuable metals of W, Zn, S and CaF2 were lost in the tailings. To make good use of the ore, the technology of fully recovering Cu, Sn, W, Zn, CaF2 and rare metals are in urgent need. After systematic researches, the flow sheet of "bulk flotation of Cu-Zn minerals at first, then Cu-Zn separation, then recovering sulphide by flotation, then recovering iron minerals by magnetic separation, then bulk flotation of Sn-W minerals after desliming" is developed. Furthermore, specific Sn-W collectors of BK411 and BK412 are applied into the processes and better indexes are obtained. The industrial indexes are listed as followings: the content of Cu, Zn, Sn, WO3 of ROM ore is 0.31%, 0.65%, 0.13%, 0.03%; Cu and Zn recovery are 82.23% and 37.79% respectively; 63.76% of Sn and 34.34% of WO3 go into the Sn-W bulk concentrates. Economic benefits are remarkable."

Jan 1, 2014

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By G. N. Jadhav

In India, bauxite deposits are concentrated in Central India, Western Ghats and Eastern Ghats. Bauxites from various regions in Gujarat were identified during the present investigations of geochemical mapping. Different types of Bauxites samples were collected from Kachchh, Jamnagar, Porbunder, Junagarh, Bhavnagar and Amreli areas of Gujarat state and were studied in detail for their geochemical signatures to plot the data on Geochemical map. Raw bauxites were characterized by using powder XRD, XRF, ICP and optical microscopy techniques (with the help of Model microscope having both transmitted and reflected light setups) and were later examined to grade their quality. Most of the bauxites from Kachchh region were of high-grade (gibbsitic) type; while those of Sourashtra region were of low-grade (lateritic / calcitic) types. Most of these bauxites were either of ferruginous/lateritic or of calcareous/calcitic types. Based on the mineralogical composition, such as gibbsite, hematite and/or goethite, Kaolinite and calcite minerals present in particular bauxites, the deposits were graded. Finally, the Geochemical mapping of Bauxites for Gujarat region was prepared and discussed.

Sep 1, 2012

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By Kwan Ho Kim

The beneficiation study of low quality pyrophyllite is conducted to enhance the value of it by selective grinding. In mining stage, the main gangue mineral is quartz, and the content of quartz in ore has an adverse effect on the quality of pyrophyllite. Using the huge difference in hardness between quartz and pyrophyllite, the selective grinding is accomplished using stirred ball mill. As a result, a finer pyrophyllite particle can be easily separated from coarser quartz particle by simple size classification, and the content of Al2O3 of fine particle smaller than 45um increased largely. It means that the pyrophyllite particle is ground selectively compared to the quartz particle, and the quality of pyrophyllite is enhanced.

Sep 1, 2012

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003