Search Documents

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By David I. Verrelli, Peter T. L. Koh

"Recent experimental measurements of induction time made by direct observation with the ‘Milli-Timer’ indicated that angular particles were able to attach much more rapidly than spherical particles. There was around a tenfold difference in the respective induction periods for particle-bubble attachment. For industrial application, a more holistic comparison is needed, with the induction period for attachment being just one input. Over the years, CSIRO has developed a CFD-flotation model that incorporates both rigorous hydrodynamics, to simulate real industrial cell geometries, and a detailed model of the embedded flotation process, in which the induction period is an important parameter. We conducted transient modelling of batch flotation. First, spherical particles were modelled, as a ‘baseline’, for different particle sizes and levels of hydrophobicity. In the second set of results, the induction period was decreased by a factor of up to ten, simulating flotation of angular particles. Flotation recovery was found to depend upon induction period in a complex manner. For highly hydrophobic or fine particles, the induction period for spheres was already so low that recovery was limited by other factors (e.g. bubble-particle collision frequency). Further decreases in induction period, as for angular particles, did not have a significant effect on recovery in these cases. By contrast, when weakly hydrophobic or coarse particles were modelled, the recovery was predicted to be greatly enhanced for angular particles, in comparison to spheres. For these particles the induction period was limiting recovery, so that the flotation rate constant could be improved directly by reducing the induction period. This is consistent with batch flotation experiments using Ballotini reported earlier. Therefore, when dealing with weakly hydrophobic particles or relatively large particles that are to be floated, an enhancement can be expected for more angular particle shapes. In such cases, judicious specification of the grinding circuit may improve the overall efficiency."

Jan 1, 2014

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate. The technology has been tested on several different waters in pilot plant campaigns. Results obtained indicate that potable water can be produced (containing less than 200 mg/L sulphate and no heavy metals) as long as the monavalent ions (Na+, Cl-, etc.) are within limits.

Jan 1, 2003

By Gülay Bulut, Ünzile Yenial

"Water composition has a significant effect on flotation. A better understand the role of water composition in flotation is very important for process quality and performance. Based on source of process water, the concentrations of the dissolved ions, hardness, contaminants and residual composition of reagents can varied in the process water. The various water resources employed during lead and zinc flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed on the ore, whilst ions associated with gangue minerals were released into the flotation pulp.This paper includes a research for the effect of different water compositions on lead and zinc sulphide flotation. Experiments were carried out five types of water such as tap water, recycling water, tailing dam water, underground mine water and sea water. The ore sample was obtained from Esan Balikesir-Balya mine. The mineralogical study of ore sample shows that it contains mainly galena, sphalerite, pyrite, hematite, quartz, diopside, epidote, calcite, and chlorite. It is found that recycling water and tailing dam water has a positive effect on recovery of lead and zinc minerals and detrimental effect on content of both minerals. This result may explain with remaining reagents in these waters. Underground mine water and tap water gave nearly the same recoveries of zinc. Sea water affects the recovery lead and zinc negatively."

Jan 1, 2014

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By Y. Q. He

The methodology of active pulsing air separation is a new method for dry material classification. Especially, it is suitable to electronic scraps disposal and re-utilization. By studying the difference of drag coefficients of the particles moving through areas of varying Reynolds numbers, and considering the extra-mass forces acting on the particles in the active pulsing air field, models of the dynamic motion which particles follow were developed. A computer simulation was prepared that showed the traces of particles with different densities and/or diameters, but similar aerodynamic characteristics, as they moved through the turbulent flow, to modify and define the parameters of the models. The simulation was found to predict the observed results with artificial tracing spheres being separated by the laboratory equipment. The separation performance, as being affected by the particles, nature, the air velocity, the pulsing frequency and the air pattern, is discussed. In general, lower density particles are more responsive to variations in airflow velocity. In addition, an industrial scale active pulsing air separator was designed, and it provides a new and efficient method for resource re-utilization in China.

Jan 1, 2014

By Kaioeng Wang, Qi Liu, Yahui Xiang

"In the differential metal sulfide ore flotation it is desirable to replace the toxic inorganic depressants with environmentally benign chemicals. Chitosan, as a natural and non-toxic polymer, has been proven to be an efficient depressant for chalcopyrite while allowing galena to be floated by xanthate collectors. However, the poor solubility of chitosan limits its potential applications as the flotation could only be carried out at about pH 4 where chitosan is soluble. A carboxymethyl derivative of chitosan, named N-carboxymethyl chitosan (N-CMC), was synthesized by substituting the amino groups of chitosan with carboxymethyl groups. The substitution significantly improved the solubility of chitosan. The structure of N-CMC was studied and compared with chitosan via Fourier transform infrared spectroscopy (FTIR). Flotation tests were performed on single minerals and mineral mixtures (with weight ratio of 1:1) with the addition of appropriate amount of potassium ethyl xanthate (KEX) and N-CMC. The solution pH was varied from neutral to alkaline. The flotation concentrates and tailings were collected and analysed for the contents of copper and lead. FTIR measurements showed that new peaks of C=O stretching of -COOH and N-H deformation of -NH- appeared in N-CMC, which indicated that the carboxymethyl groups were introduced and the amino groups were the sites for the substitution. Flotation results indicated that N-CMC could depress either chalcopyrite or galena depending on the pH. The results were not affected by the sequence of KEX and N-CMC addition. Therefore, N-CMC is potentially useful in Cu-Pb sulfide separation following a bulk Cu-Pb flotation. The N-CMC was also found to have surface cleaning functions, and was able to remove contaminating copper ions from galena surfaces. Therefore, its application in sulfide ore flotation is expected to be more robust than the original chitosan."

Jan 1, 2014

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By Gábor Mucsi, Barnabás Csoke, Viktor Mádai, Zoltán Molnár, Viktor Török, Ádám Rácz

The application of the stirred media mill in dry mode came to the front only in recent years, but at the same time several questions arise, such as aggregation, agglomeration, sticking on the liners and the grinding media. During high energy milling, not only the particle size reduces, but among others, in numerous cases the crystal structure and the amorphous state of the material also change due to the mechanical activation taking place. The present paper deals with experiments carried out on the ultrafine fly ash grinding in dry mode at various grinding conditions in a stirred media mill to investigate the mechanochemical effect and the energy efficiency of the mill. During the experiments the particle size distribution, particle shape, specific surface area, amorphity and crystal structure of the products were examined. The product related stress model was used for the evaluation of the effect of milling parameters on the mechanical activation. It was found, based on the experimental results, that there is mechanochemical effect on crystal structure of fly ash in the stirred media mill, as it was revealed by X-ray diffraction and FTIR measurements. The experimental results made it possible to determine the effect of the rotor circumferential speed and so the stress intensity on the mechanical activation of fly ash could be revealed.

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Saveliy F. Kaplan, Valeriy N. Tsyplakov, Vasily N. Kovalev, Igor A. Agapov, Nikolai V. Vorob’ev-Desyatovskii

"Based on the experiments, a possibility of successful processing of double-refractory gold sulphide concentrates with a high content of natural organic carbon, which has a high sorption capacity toward gold chloride complexes, has been demonstrated. The proposed approach involves deep burnout of sorption-active organic carbon in an autoclave at a higher temperature and a longer retention time. INTRODUCTION It is known that one of the reasons why gold-bearing ores and concentrates are refractory is the occurrence of fine gold in sulphides (usually in pyrite and arsenopyrite) in ores and concentrates. In addition, refractory gold-bearing ores and concentrates also contain an organic carbonaceous material, which has a sorption capacity towards gold chloride complex, making the ore or concentrate even more refractory. In pressure oxidation, metallic gold is oxidized by Fe (III) aqua-ions and complex Au(Cl)4- ions are formed at temperatures over 180°C, in the presence of chlorides contained in ores. Complex gold anion is adsorbed on the organic carbon surface and then reduced to Au0; the chloride ion is regenerated and gold, adsorbed on organic carbon microparticles, is ultimately transferred to tailings (preg-robbing). Currently, there are several suggestions how to suppress preg-robbing (Simmons, 1998, Pyke, 1999, Rees, van Deventer, 2000, Zhao Jun-wei, 2008). It can be done by reducing the organic carbon content by processing (flotation, etc.),reducing chloride ion concentration by preliminary washing of concentrates in thickeners, reducing the adsorption capacity of organic carbonaceous material by introducing some organic substances that are strongly adsorbed on its surface (blanking agents), and reducing the redox potential of the slurry liquids by introducing neutralizing agents (limestone)."

Jan 1, 2018

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003