Search Documents

By Ke Yang

"Drilled shafts are typically used to support structures subjected to large moments at the shaft head. The large moment can produce push and pull forces on the two sides of a drilled shaft. Consequently, the applied moment is partially resisted by the push-pull moment resistance induced from the vertical side shears. This type of push-pull resistance has not been fully recognized in most design and analysis methods. In this paper, a 30 finite element model for a drilled shaft subjected to lateral load and moment is presented and is validated against two field lateral load tests. Based on the 30 finite element model, a parametric study is carried out. It shows that the push-pull moment can resist 18-35% of the applied moment. The parametric study also shows that the push-pull resistance varies linearly with loading eccentricity when the eccentricity is less than the shaft embedment length. A method to estimate the push-pull resistance is proposed based on the results of the parametric study. Then, a new method for lateral capacity prediction is proposed to account for the push-pull resistance. The base shear resistance is significant for short drilled shafts; therefore it is also included in the proposed method. A case study on four lateral load field tests illustrates that the new method could improve the accuracy of lateral capacity prediction when compared with the traditional Broms method.INTRODUCTIONDrilled shafts are typically used to support a variety of structures subjected to large moments. Sound walls, highway signs, traffic signals, high-rise buildings, electrical transmission towers, and bridge piers are examples of cases where lateral loads with large eccentricity would result in high overturning moments on foundations.Current analysis methods for capacity predictions (Broms, 1964a and 1964b; Brinch Hansen, 1961) or deflection predictions (Reese, et al. 197 4) of laterally loaded drilled shafts are based on the lateral resistance of soils and rocks. However, O'Neill pointed out that moments can be partially resisted through the push-pull resistance provided by the vertical side shears due to the rotation of the pile (Reese, 1997)."

Jan 1, 2005

By Charles M. Wilk

"Solidification/stabilization (S/S) treatment is used to treat hazardous wastes for disposal and in the remediation/site restoration of contaminated land . SIS is also an increasingly popular technology for Brownfield (industrial property) redevelopment, since treated wastes can often be left on-site and to improve the soil for subsequent construction. This paper discusses the applicability of the technology to various wastes, basic cement chemistry relating to SIS, tests used to design treatability studies and to verify treatment, basics on implementation of the technology in the field , and examples of SIS use at brownfield sites, including a former wood preserving site, former manufactured gas plant sites, a former electric generating station, and a shopping mall development.INTRODUCTIONSolidification/Stabilization (S/S) is a widely used treatment for the management/disposal of a broad range of contaminated media and wastes; particularly those contaminated with substances classified as hazardous in the United States. The treatment involves mixing a binding reagent into the contaminated media or waste. The treatment protects human health and the environment by immobilizing contaminants within the treated material. Immobilization within the treated material prevents migration of the contaminants to human, animal and plant receptors. SIS treatment has been used to treat radioactive wastes since the 1950s and hazardous waste since the 1970's (Conner 1990). SIS continues as a cornerstone treatment technology for the management of radioactive waste, hazardous waste, and site remediation and Brownfield redevelopment."

Jan 1, 2005

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Frank Rausche

Why testing What tests can be done Dynamic load testing Loading device Measurements Analysis Examples

Jan 1, 2001

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Edmund Cardoza

In the spring of 1993, construction began on an ambitious building project in Boston, Massachusetts. The Shriners organization committed to offer state-of-the-art adolescent burn treatment and rehabilitation in its Boston facility by expanding in a most unusual way. In short, the concept included installation of caisson foundations and perimeter slurry wall panels to enable construction of a completely independent structure around and above the existing, continually functioning, hospital. Two distinct phases of work were detailed in the Contract Documents. At the completion of the first phase, patients will be moved into the new building, above, and demolition of the old structure, beneath, will be performed. In Phase I, sections of the slurry wall and caissons, located outside the footprint of the existing building, were planned. The next phase of the work includes the installation of the remaining caissons and slurry wall. Once excavation is completed, the balance of the new hospital structure will be constructed from the bottom upward, connecting to the under side of the new structure.

Jan 1, 1994

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Jesús E. Gómez

A total of 260 micropiles were installed as part of a retrofit effort for two existing bridges. The micropiles consisted of hollow core bars installed under limited headroom conditions. Of the total number of micropiles, 180 were installed in submerged sand and 80 were installed in stiff, silty clay. The micropiles were drilled using a lean cement grout which was re-circulated for de-sanding and re-use. Final grout was injected upon completion of drilling to the design tip elevation. The micropiles were subject to a rigorous quality control that included grout quality testing and proof-testing of each production micropile. This paper presents a description of the procedure for installation and quality control of the micropiles. The successful proof-testing of all the production micropiles showed that hollow core bar micropiles can be used effectively in granular and fine-grained soils. Hollow core bar micropiles offer particular advantages when installed in submerged sand formations with respect to other traditional micropile types. The results of the proof load tests are presented in a companion paper.

Jan 1, 2007

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By K. Viking

It&apos;s well known that conventional impact hammers, usually are the method to use in order to drive precast prestressed concrete piles. However sometimes the vibratory technique might be considered as a suitable alternative due to favourable soil conditions. It is also well known that piles driven into granular soils can be installed more efficiently by the use of a vibratory driver compared with impact hammers. However, the use of the vibratory technique is seldom regarded as the first choice, since the technique is constrained by several uncertainties related to the pile capacity, and concrete piles to cope with tensile stresses. With the opportunities of having suitable subsurface conditions and a fair amount of piles to be installed, it was anticipated that the use of the vibratory method could result in a significant reduction of the installation costs. Part of the uncertainties of using a vibrator was intended to be eliminated by restriking the vibratory driven pile with an impact hammer and use a Pile Driving Analyzer? (PDA) to correlate recordings of soil resistance to driving with measured rate of penetration, and to evaluate the static capacity and load/settlement characteristics of the vibratory driven pile by conducting static load test. The conducted test study of using a vibrator to drive the precast prestressed test pile (14-in. square by 30-ft-long) did not turn out to the author&apos;s complete satisfaction. The present paper focuses mainly on a numerous practical engineering issues in relation to the use of the vibro-technique to drive precast prestressed concrete piles in granular soils. The obtained experiences of using a PDA to monitor vibro-driven piles, with its potential and limitations, is presented and discussed. Furthermore, a simple method of how to subjectively pre-estimate the soil resistance due to vibratory driving is presented and discussed. The reasons for the partly unsuccessful test study are discussed in great detail based on the obtained experiences. Suggestions of how to better approach a similar situation in the future are also provided in great detail

Jan 1, 2004

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Michael J. Garlich

Steel sheet piling has a long history of use in a variety of permanent and temporary structures. Current engineering practice uses numerous publications and standards for design guidance. U.S. design guidance is fragmented, with numerous inconsistencies between design guides. To improve current U.S. design practice, the North American Steel Sheet Piling Association has initiated a project to produce a design standard that will unify design procedures and provide specification guidance for engineers and users of steel sheet piling. The wide range of uses for sheet pile structures presents a challenge in developing such a standard. Load factors or allowable stresses acceptable for a temporary retaining wall in soil may reasonably vary from those for a river cofferdam or a dockwall located in sea water. However, it is still possible to provide consistent and rational guidance for such varying uses. The standard also can address sheet pile design aspects often neglected in U.S. publications, such as vertical load capacity and resistance to loads applied parallel to the sheeting.

Jan 1, 2008