Search Documents

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Aly M. Mohammad

The Howland Hook Terminal Facility located in Staten Island, New York is one of the most active container terminals in the Northeast United States. Due to the high capacity of the facility, the Port Authority of New York and New Jersey (PANYNJ) recently acquired the adjacent 37-acre Port Ivory Facility. Expansion of this Site facilitates the additional transfer of goods for rail transport, where formerly the facility was solely highway transport. Upon completion, the facility will have the ability to transfer containers directly to a freight rail line onsite by crossing from Howland Hook Site to the Port Ivory Site via a proposed bridge over Bridge Creek. The geology of the Port Ivory Site consists of shallow glacial deposits left by the leading edge of the last advance of the Wisconsin Glacier. Glacial and marine action over the millennia and the modifications of past construction combined to form a challenging site geologically. Prior to the PANYNJ acquiring the site, the Port Ivory Facility was occupied by Proctor and Gamble for nearly 100 years. Over the course of time, the site has had a variety of structures constructed and demolished at the site. The earliest structures were often supported on shallow foundations and the foundation types used progressed over the years transitioning from low capacity timber piles to various new pile types as they became available; such as Raymond tapered piles, steel piles with concrete cores, precast piles and cast in place foundations. Currently, we are designing 4-foot diameter high capacity drilled shafts to support a new bridge over Bridge Creek to connect the two sites. Drilled shafts proved to be a very economical solution from both a design and construction point of view to carry the axial load of the bridge of approximately 400 tons per shaft. The paper will present a historical evolution of the progress of deep foundation types used at the Port Ivory Site; from low capacity timber piles to high capacity large diameter drilled shafts. The paper will also present changes and modifications of geotechnical design criteria over time that affects the type of deep foundations used. For instance, utilizing new seismic design criteria requires selecting a deep foundation system that withstands seismic loading conditions and overcomes the effects of liquefaction.

Jan 1, 2004

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

Jan 1, 2017

By Mitsuhiro Shibazaki

Generally, water-soluble polymers are effective in convergence of water jet ejected from a nozzle as they add viscosity to water. However, excessive additional polymers (added to keep water viscous) could increase friction on the contrary. Therefore, we have totally modified the jetting system from every possible aspect, such as the shape and upstream conditions of a nozzle in order to keep the flow spread to the minimum as stated in my presentation.

Feb 10, 2003

By George Burke

Of the three projects, particularly the extensive Nimitz II (downtown) project, a single system, which was part of the operation, was used to control the spoil. Spoil control was continuous with the work since a vacuum truck and crew was used to suck up the spoils as they came out of the borehole. So, the whole job was kept clean both during operations and at the end of the shifts. On the Sand Island project, a double system was used. Larger spoil quantities were contained within the shaft limits during the work and the cleanup or disposal of the spoils was performed during excavation.

Feb 10, 2003

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By John Davie

We used a Remtek survey in Glenrock and had very good luck with it when we first started the initial investigation. We would have loved to have used that more but my understanding is the equipment is hard to find. It also requires a flooded mine workings. If you're in a dry mine the communication between the two holes is not quite as successful.

Feb 10, 2003

By Marcus Daubner

This paper explains how BAUER Spezialtiefbau GmbH uses digital methods on projects - starting from work preparation to completion of works. More precisely, the advantages of BIM-based planning during work preparation and the automated and structured data management - both machine production data and the manually recorded quality-relevant reports - during execution phase are displayed. In this context, the benefit of the digital twin to optimize processes, to reduce defect costs, for a more effective reporting sys-tem, and the further usage of as-built information in the BIM or GIS process is described.

Sep 1, 2022

By Dario Libano, Armando Caputo, Francisco Caputo

"UHE Peixe Angical is a 452 MW hydroelectric power plant located on the Tocantins River in Tocantins, Brazil. In 1999, geologists began feasibility studies to estimate the river’s hydroelectric potential, and the decision was made to proceed with the construction of a power plant. In 2002, after extensive investigation, the studies indicated geological homogeneity at the site for the dam, except for an anomaly detected on the left margin, and construction began on the $1.2 billion project.As the work began, the complex ground conditions presented several serious difficulties. The solution was unlike any undertaken before in Brazil— a 100-m-long secant cutoff wall, with 76 1.8-m-diameter piles of up to 78 m deep. All were placed in a six-month period.In the preparation for the detailed construction plans, further studies in the area of the anomaly better defined the geology so that a treatment program could be developed. The feasibility study had detected silicified rock with high permeability in one area, and an injection curtain was designed with five injection lines. In the other area with an anomaly, further investigation revealed a permeable marble formation that was 50 m thick. Here, a specific injection program with three injection lines was developed.The injections started in February 2005 in the marble formation area. By July of that year, only the primary and secondary holes were drilled from the three lines, resulting in a space between injections of 1.50 m. By the end of July, the drilling was halted. The contractor had identified a thick area of heterogeneous material below the transition zone that was characterized by a mixture of soil, fractured rock and hard fractured rock. The anomalies were detected while drilling, and both the general contractor and the designer concluded that the phenomenon of “piping” was taking place.Constructing a positive cutoff wall became a priority."

Jan 1, 2009

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By Gary T. Brill

In the presentation, the development and new applications of the jet grouting technique in the North America are briefly introduced at first and followed by the outline and advantages of Jet Grouting. Several recent projects for jet grouting are presented in which the applications to underpinning and excavation support, foundation, groundwater barrier and seismic stabilization are briefly discussed.

Feb 10, 2003

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005

By Franz-Werner Gerressen

New developments are required each day as our industry becomes more competitive. To improve performance, continue and to ensure future demands can be met. This requires the development of technical support systems that enable a more constant delivery and quality of installation of pile foundations and other applications. For example: assistance systems capable of relieving the machine operator of automating monotonous or repetitive operations. Real time installation control of the production process to manage quality control, or data transfer and reporting systems capable of keeping pace with the digital future. This paper will describe these new approaches and considerations required for these new developments. The paper also describes the equipment which is needed to execute the work under the various conditions and provides references herein. INTRODUCTION The success of a construction site is influenced by a number of factors. Selecting the most efficient and economic methods during the planning phase to defining the right direction. This means having multifunctional equipment available. To ease the usage of this equipment by the operator, uniform operation and control systems are essential. Systems like this can provide uniform handling procedure for more than 20 different installation techniques. Experienced operators are not always available. Therefore, to ease the start for beginners and to support training, numerous assistance systems were developed. This ranges from simple information for controls shown on the monitor avoiding misuse to systems which can partly automate the construction process. Regardless, the best equipment is not enough when the construction is not running smooth. The control system not only helps to organize and coordinate service of the equipment; moreover, it allows the operator to control the quality during the installation process reacting if needed. It allows process optimization as well as documentation which might be required for later negotiations.

Jan 1, 2019

By Jim Bruce

No answer required. From the drilling equipment suppliers, but the specifications must be tailored to be project-specific. Yes, the sonic technique is very interesting as we said, and it is not so much as an issue of the magnitude of power, it's about the efficient use of the power. The efficiency of the machine is not necessarily related to size so it is best to talk to the two contractors that supply the service about that. I think it can be scaled down but it is quite a big head, so therefore there are practical limitations on the size of the door it can walk through and also the size of the casings and rods that it can use. You might defeat the economic advantages if you were to use too short casing lengths. Boart Longyear have a low head room machine that can work within an 8 foot verical clearance.

Feb 10, 2003

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy"

Jan 1, 2017