Search Documents

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By P. Dupeuble

Diaphragm walls, owing to their method of construction are discontinuous structures. A new technology for the construction of joints between panels has been developed. This new process allows for the construction of diaphragm walls with mechanical and watertight continuity.

Jan 1, 2010

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By Jon H. Gould

This paper describes the following at the new Advanced Solid Rocket Motor (ASRM) nozzle manufacturing facility, which is being constructed inside an existing manufacturing facility: 1) generalized subsurface conditions, 2) pile load test program and evaluation, 3) pile selection, 4) problems associated with pile driving operations, and 5) production pile installation. The poor subsurface conditions, known and unknown underground obstructions, and work environment inside the existing building, used to manufacture the Space Shuttle external fuel tanks, required special pile installation equipment, procedures, and work schedules to install the economical pile foundation system ahead of schedule and without a lost time accident. GEOTECHNICAL STUDIES In April and May 1990, 16 soil test borings were drilled inside the existing building with a truck-mounted drill rig. The borings extended to depths ranging from 60 to 65 ft (18.3 to 19.8 m) below the floor slab. Typically, the silty and clayey soils were sampled by pushing "undisturbed" Shelby tubes, and the more sandy soils were sampled by driving a Standard Penetration Test (SPT) split-spoon sampler. The unconfined compressive strength, water content, and unit weight of the Shelby tube samples were measured in the laboratory. A geotechnical report was issued in May 1990 presenting the results of the field and laboratory testing and foundation recommendations (Gilbert, 1990).

Jan 1, 1992

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By D. V. Roberts

Approximately 800 private consulting engineering firms in America specialize in geotechnical engineering. The gross income from these firms totals about $500 to $600 million per year. Sixty-five to seventy-five percent of this geotechnical work is per­formed by consulting engineers that belong to the Association of Soil and Foundation Engineers (ASFE). This paper presents statistics concerning the business activities and functions provided by ASFE member firms. The procedures used in typical projects are described. The paper concludes with a summary of major trends which are impacting the American geotechnical practice today.

Jan 1, 2010

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000