Search Documents

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By Barnard Foo

Topics of Discussion ?Location ?Production & Mining Operation ?Mineralization ?Mining Method ?Rock Mechanics Issues ?Ground Control Problems ?Numerical Analysis ?RockmassBehaviour ?Conclusions & Recommendations ?Discussion

Feb 1, 2008

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By Peter Radziszewski

"Typical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5% to 20% ). Cornminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and linerkharge wear (50 %). Developing the ability of predicting mill wear will allow a more accurate estimation of wear costs. However, total media wear in a given ball mill grinding process is a product of three recognized wear mechanisms those being abrasion, corrosion and impact. Further, the contribution to total media wear of each of these wear mechanisms has not been well established. In this paper, a overview of abrasive, corrosive and impact wear mechanisms is made from which an empirical wear prediction procedure is proposed. Further, future directions in wear prediction research is outlined. INTRODUCTIONTypical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5 % to 20 %). Comminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and lined-charge wear (50 %). With respect to wear, world wide steel consumption as grinding media is estimated at over 600 000 tomes per annum (Malghan, 1982). As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs.Charge media wear prediction is actually estimated using the Bond abrasion test. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2000

By M. Veiga, L. Lavkulich, R. Pakalnis, M. Ghomshei, S. Baldwin, J. A. Meech

"On July 26, 2000, the Canada Foundation for Innovation announced an award of $1.3 M dollars for The Centre for Environmental Research in Minerals, Metals and Materials, CERM3, at The University of British Columbia. Additional funding was also provided by the British Columbia Knowledge Development Fund ($1.3 M) and the UBC Stewart Blusson Fund ($0.7 M). Annual industrial grants and contracts are providing support funding for the on-going research projects. Corporate membership in CERM3 entitles each participant to a seat on the technical advisory committee (TAC) as well as access to the five laboratory facilities currently under construction. Both the federal and provincial governments will also participate in the TAC through NRCan-CANMET and the BC Ministry of Energy and Mines, respectively. CERM3’s mission is:• to develop innovative methods to deal with environmental problems created by mining activity;• to promote sustainable development as a hallmark of management decision-making; • to produce mining and processing engineers with the required environmental skills; and• to enhance the image of mining in society as a vibrant and necessary component of a modern economy and society which disturbs the environment for the benefit of mankind.CERM3 brings together a multi-disciplinary team of researchers from over 12 departments at The University of British Columbia (UBC) to work on mining-related environmental problems. These include: chemistry; soil sciences; chemical and biological engineering; earth and ocean sciences; microbiology; civil engineering; electrical engineering; metals and materials engineering; mechanical engineering; mining and mineral processing, the Westwater Research Centre; the Institute for Resources and the Environment; and the School of Occupational and Environmental Hygiene. The centre intends to interact with scientists from industry, governments and other universities across Canada and around the world. CERM3 aims to become Canada’s leading environmental research facility for the mining industry. This paper describes the evolution of CERM3 and its coordinated multi-disciplinary approach to mining and the environment. Some of CERM3’s research projects include:• developing new protocols for environmental analyses to provide consistent and reliable assays;• isolating a natural virus for Thiobacillus ferrooxidans and other bacteria responsible for acid rock drainage (ARD);• designing bio-remediation and adsorption techniques for mine effluents;• promoting and enhancing the use of hydrometallurgy to reduce environmental pollution;• examining new approaches to comminution to decrease energy consumption;• developing a magnetically levitated hoisting system to reduce the footprint of a mine operation;• building a state-of-the-art supercomputer network laboratory for mine/mill simulations; and• designing intelligent bulkheads to seal tunnels following mine closure to survive for 1000 years.This latter project involves the establishment of a research station at the Britannia mine site, 45 km north of Vancouver, which will provide a full-scale facility to design the “Millennium Plug” and contribute directly to the solution to one of North America’s worst ARD-contaminated sites."

Jan 1, 2003

By Oy Leuangthong

Red Dog mine is the world's largest Zn producer. The deposit consists of sulphide ore zones in sedimentary exhalative (sedex) deposits, and is characterized by the presence of multiple metals and multiple ore types. The objective of the case study is to characterize seven different minerals, Zn, Pb, Fe, Ba, sPb, Ag and TOC, within eight different rock types. Geostatistical models were constructed for each variable within the eight rock types, and subsequently assembled to give 40 realizations for six 25ft benches. The stepwise conditional transformation was used to account for the complex multivariate relations. In addition to reproducing the input data, histogram and variogram, the resulting models also respect multivariate relations locally and globally. This paper documents the methodology to construct these models. A thorough validation procedure was implemented. Comparisons with blasthole data show that the conditional simulations and the long-term models agree in expected value. The main advantages of the conditional simulations are (1) the explicit accounting of multivariate relations between the data in model construction, and (2) the ability to quantify variability and uncertainty at any scale. A small exercise comparing the profit from a kriged and a simulated model is also examined. Results show that the simulation approach showed a 3% increase in profit, relative to the conventional estimation approach.

May 1, 2004

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By A. Rajan

"Drawing upon the experiences of a gold extraction plant startup in the Southern Pacific, this paper will describe the importance of the commissioning phases to the project outcomes to achieve early target production despite an overall time compression to attain full plant production. Some of the highlights of the paper include: impact of roles played by the Owner’s construction and operations representatives during project commissioning, the formation of a capable and competent “Mod Squad,” availability of trained operating personnel, control over work priorities and the scope of work needed to bring the plant to safe initial operations. The commissioning team comprised subject matter experts skilled in process technology supported by “generalists” thoroughly conversant in overall plant operations. The merits of a structured team approach to brainstorm and resolve commissioning challenges as opposed to direction from individual subject matter experts is discussed. IntroductionStartup or commissioning is a unique period in the life of a project. Each stage of a project-exploration, feasibility, design, construction, commissioning, initial operations and continuing operations-requires special talents, know-how, and practices. Each stage makes particular demands of the people involved. Initial operations are no exception.Having experienced the 1997 startup phases of oxide and sulfide facilities for a gold extraction plant at a remote island in the Southern Pacific, I can attest to the many challenges and rewards. Commissioning for both facilities was extremely successful and brought the entire project on line well ahead of the targeted completion dates. Using this specific project as an example, this paper will highlight some of the key features of project commissioning. In this paper, the term “pre-commissioning” denotes all activities that lead to mechanical completion; “commissioning” occurs when feed is introduced; and “initial operations” are defined as the duration when operations accepts the system/facility and takes over."

Jan 1, 2000

By Donald E. Wakefeld

"The pace at which mining will occur in Northern regions and Arctic lands will depend on the answers to a number of questions. Who are the local aboriginal participants? What land uses are they pursuing? What are their objectives? What is their understanding of the process of mining development? This paper will focus on the last question, communicating the process of mineral development to local aboriginal communities.IntroductionIn the environmental impact hearings for the BHP-DiaMet diamond mine, the smaller Dene Treaty 8 Nation argued for the settlement of its Land Claims as a pre-condition to development. However, the larger Dene Treaty 11 Nation were prepared to permit the mine to proceed on the basis that their people would receive benefits during the construction and operation of the mine.Wherever mining is the significant basis for tax revenues and economic development expectations may be encouraged beyond the realities of the situation. Izok Lake has been known for several decades as a significant mineral deposit but because of its size and the transportation costs involved, it is now a “frozen” ore body. The extent of its mineralization at current metal prices will not support the mining and processing costs without substantial government support for infrastructure and roads. At the opposite side of Canada, Voisey’s Bay clearly satisfies all technical criteria but, nonetheless, two Inuit groups, the Innu, and Métis, have all made LandClaims relating to the mine area.Contrasting the mineral deposits at Voisey’s Bay and Izok Lake emphasizes that the timing of production is dependent on factors such as the grade and amount of reserves, their market price, location and availability of government support. Nonetheless, it is this author’s thesis that given an economic orebody the next most important factor is good communications. It is his view that Arctic mineral development will occur quickly only where good communication has resulted in the trust and mutual respect necessary to implement the mammoth cultural changes required."

Jan 1, 1996

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By R. Agius, A. Nacu

"Adoption of the International Cyanide Management Code, regulatory requirements and community concerns have increased the need to implement suitable cyanide destruction processes at gold operations to meet ever more stringent discharge limits. As standards set for the allowable concentrations of cyanide, cyanide compounds and other contaminants may vary from country to country, jurisdiction to jurisdiction, and even from site to site, there is no “one size fits all” technological solution. Currently the most common cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide and Caro’s acid. Regardless of the process used, cyanide destruction plants must be reliable and achieve permit guidelines at all times. The selection of the most appropriate cyanide destruction process for an operation depends on several factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Only after considering all these factors together can the most effective approach be selected to achieve the permit guidelines economically and technically feasible. Finally performing the correct test work program is the most important step to ensure that the correct process design criteria can be determined to accurately calculate capital and operating costs.IntroductionThe adoption of the International Cyanide Management Code in 2005, stricter regulatory requirements and community concerns prompted by environmental incidents involving cyanide have increased the need to implement cyanide destruction processes at gold and silver operations.Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values are comprised of both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution, with the exception of cobalt complexes. Total cyanide levels in solutions are in most cases higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically, in Canada CNTOTAL levels cannot exceed 1 mg/L in solutions."

Jan 1, 2017