Search Documents

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By J. Oliver, B. Wilson, 10

"Red Dog is one of the world’s largest zinc producing mines and a significant producer of lead and silver. While some of the operational challenges relate to the mine’s location in a remote part of Alaska, there are also challenges in the mineral separation process. Recent processing upgrades have included the installation of two M5000 IsaMills to improve the zinc regrind circuit and of one Jameson Cell to improve the pre-flotation circuit. Relatively fine grinding is required to achieve efficient mineral separation at Red Dog, but while fine grinding aids in the production of high grade concentrates, it also creates challenges in the efficient recovery of fine minerals. Over half of the lead lost to the lead circuit tailings, as well as almost half of the zinc lost to the final tailings, is in the finer size fractions (<10 µm). The high pulp density experienced in the pre-flotation and lead rougher circuits also causes significant entrainment loss of lead and zinc to the pre-flotation concentrate and of zinc to the lead concentrate. To help improve fine mineral recovery, Red Dog has recently plant tested and installed magnetic conditioning technology in the flotation circuits. The equipment aggregates fine paramagnetic sulphides and selectively increases their flotation recovery. This paper outlines the testing and positive results at Red Dog.INTRODUCTIONRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine. Red Dog Ore and Mineralogy The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The main minerals present in order of abundance are: quartz, sphalerite, pyrite, barite and galena. Production began in 1989 with mining of the Main deposit. Between 1989 and 2012, approximately 55.6 million tonnes of ore with an average grade of 20.5% Zn, 5.6% Pb, and 97 g/t Ag was mined from the Main deposit. Subsequent to the development of the Main pit reserve, two additional open pit deposits were discovered: Aqqaluk and Qanaiyaq. The first blast in Aqqaluk occurred on June 4, 2010. As of December 31, 2014, the Aqqaluk deposit reserve is an estimated 45.7 million tonnes of ore with an average grade of 15.1% Zn, 3.9% Pb and 71 g/t Ag."

Jan 1, 2016

By T. I. . I. Sibbald, D. E. Jiricka

The Goldfields area on the north shore of Lake Athabasca , was active in the thirties and early fortie . In 1934, Tom Box discovered gold mineralization in quartz veins in pyritized 'granite' at the ite of what wa to become the Box Mine of the Consolidated Mining and Smelting Company of Canada Ltd . In the rush of activity that followed numerou other gold occurrences were found. the most significant of the e being the Athona and Frontier prospects which underwent underground development bur did not reach production. Probable reserve identified to date in the Box and Athona deposits amount to some 3.5 million ton grading an average 0.ITT oz gold/ton . Some 10 to 15 million tons of lower grade, po ible reserve are also reported at the Box. From 1939 to 1942, the mine produced, from underground , 64,066 ounces of gold from ore grading 0.0452 oz gold/ton at a cost of between $1.5 and $2.0 a ton. The Goldfield area is underlain by upracrustal rock intruded by mafic bodies and invaded by ·granite'. The upracru tal . thought to be of Lower Proterozoic age are characterized by a helf-type ucce ion metamorpho ed under lowermiddle amphibolire facie conditions into quartzites, quartz-mica chi ts. dolomitic marbles, diop idic calc-silicates and cordierite-anthophyllite-biotite schi t . Amphibolites of presumed igneou origin form concordant to subconcordant units up to a few ten of metre thick in the upracrustals and occur as le regular masses in the 'g ranite·. Compositionally they vary from gabbroic to granodioritic. with the more mafic varieties being most common. Granitic rocks exhibiting a variety of textural , structural and compositional characteristics underlie most of the area. Four main units are recognized: foliated (older) 'granite', 'leucogranite', feldspar augen 'granite· and pyritic mine 'granite', however, in geological mapping the e are somewhat arbitrarily differentiated due to transitional relationships and admixture of types. Although there is no unambiguous age data available for the e 'granite ' adjacent northshore 'granite' of geologically similar age yield Rb-Sr isochron dates around 2000 Ma. The area is characterized by two major deformation events of which the earliest gave rise to the dominant regional foliation and to rare minor and outcrop scale folds. This foliation which in general parallels compositional layering is folded into the major Goldfields syncline, whose axis plunges weakly to moderately outh. Related open minor folds have subvertical axial surfaces which are locally paralleled by a weakly defined schistosity. Most rock display a pronounced rodding fabric, coaxial with second fold axes and apparently the product of this deformation event. However, a note of caution is introduced into this interpretation, as the rodding fabric is also parallel to first fold axe .

Jan 1, 1986

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By T. Sugawara, H. Sekimoto

Electrorefining of low-grade copper alloys containing various amounts of nickel, lead, antimony, bismuth, arsenic, selenium, silver, and gold in sulfamic acid media was demonstrated. The copper concentration of the alloys used as an anode was 70–90 wt%. The electrolyte contained 100 g L-1 of free sulfamic acid and 40 g L-1 of cupric ion. Galvanostatic electrolysis was conducted at 200–300 A m-2 in the electrolyte using a low-grade copper alloy anode and a stainless steel cathode at 25C. The terminal voltage was approximately 0.8 V at the start of the electrolysis, although it increased periodically to approximately 2.0 V and then shortly returned to its initial value. Nickel, lead, and arsenic from the anode dissolved in the electrolyte and were removed. Antimony, bismuth, selenium, and silver were removed as solids. Consequently, a dense copper cathode was obtained, and the concentration of copper was evaluated by inductively coupled plasma – optical emission spectrometry to be 99.82–99.99 wt%. INTRODUCTION Electrorefining of copper is conventionally carried out in a sulfuric acid electrolyte using crude copper assaying at 99.5 wt% Cu as the anode (Biswas & Davenport, 1994). Elements more noble than copper do not react anodically, and consequently, they are distributed in anode slimes. Elements less noble than copper dissolve from the anode. Nickel and arsenic are stabilized as aqueous species. Lead, antimony, and bismuth react with water, sulfuric acid, or arsenic acid to form barely soluble compounds; thus, they are distributed in anode slimes. An emerging issue in the electrolytic refining of copper is an increase of impurities in crude copper used as the anode (Moats et al., 2013). This is due to an increase in the content of impurities in copper concentrates as well as an increase in the types of secondary copper feedstocks (e.g., E-Scraps, automotive shredder residues, and smelting residues) treated in the copper pyrometallurgical process. An extreme case is a copper smelter that does not use copper concentrates as feedstocks. In such a process, copper-bearing feedstocks are smelted in a top submerged lance furnace to prepare low-grade copper alloys assaying at 80– 90 wt% Cu (Sekimoto et al., 2013). Such low-grade copper is not acceptable as an anode in the conventional copper electrolytic refining process because it is easily passivated during electrolysis. Consequently, electrolytic copper is produced by leaching the atomized low-grade copper in a sulfuric acid solution with oxygen, followed by electrowinning. However, electrowinning should be avoided whenever possible because the electrical energy consumed in electrowinning is 5–10 times higher than that consumed in electrorefining. Therefore, the development of technologies for electrorefining of low-grade copper alloys is desirabl.

Jan 1, 2019

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment&apos;s usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931