Search Documents

By D. Kao, J. Gogal, S. Humphrey, T. Byrne, M. Davoodi

"High total and dissolved uranium values were noted in the process water at the Cigar Lake Operation (CLO) during early production start-up period, whereas significant levels of dissolved uranium had not been observed previously at similar operations. The excess dissolved uranium resulted in higher demands on the water treatment plant, along with higher operating costs, environmental risks and some unrealized revenue potential. A species balance indicated that uranium was leaching into solution in the grinding, dewatering, and storage circuits under normal operating conditions. Jet boring, water recycle, ball milling, and the use of Pachuca tanks for ore storage results in a highly oxidative environment, which is favourable to leaching.This paper will outline the testwork performed to identify the conditions under which the uranium leaches into solution and to determine required conditions for uranium precipitation. Maximum uranium leaching was found to occur under normal operating conditions (pH ranging from 7.0 to 8.5); testwork indicated that both lowering and raising the pH can significantly reduce the uranium leaching. Analytical results combined with the batch scale testwork indicate that the uranium solubility is associated with carbonate species in the ore. Uranium precipitation was maximized at pH values greater than 10.5 or less than 6, corresponding well to carbonate leaching and precipitation values from literature. Higher precipitation efficiencies were noted at high pH ranges.As a result of this work, a pH control system has been implemented in the Pachuca storage vessels and thickener prior to water treatment plant on a trial basis. Caustic soda is recommended for pH control due to ease of operation, economic viability and material requirements and downstream constraints."

Jan 1, 2016

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

By W. A. Plachner, Schiller E. A., S. P. Santiago

"The Monkman Coal Property is located in the Northeast Coal Block of British Columbia. It is divided into the Duke Mountain Block on the north east and the Dip Slope on the west. Together, these areas cover 39,503 ha of coal licences.The property is underlain by Jurassic and Lower Cretaceous marine and continental sedimentary rocks. Economic coal measures are contained within the Gates Formation. Exploration of the property began in the early I970s, with drilling commencing in 1975. To date, 255 holes have been drilled and nine adits have been driven to recover unoxidized coal samples.The property has a geological resource potential of 2.8 billion tonnes of medium and high-volatile bituminous coal. Medium-volatile bituminous reserves, totalling 68.9 million ROM tonnes at an over-all strip ratio of 6.3:1, have been identified in three pit areas in the Duke Mountain Block.Construction start-up will commence when sales contracts are arranged. The clean coal will be exported via the Ridley Island Terminal at Prince Rupert.IntroductionThe Monkman Coal Property is located in the Northeast Coal Block of British Columbia in the southern port ion of the Peace River Coalfield. The coal field encompasses a strike length of 250 km of Lower Cretaceous coal-bearing strata in which 13 companies have identified several billion tonnes of resources and several hundred million tonnes of reserves. Currently, two companies with contracts are in the construction phase, and are scheduled to produce coal by early 1984. Quintette Coal Ltd. has a contract with Japanese steel mills to supply annually 5.0 million tonnes of metallurgical and 1.5 million tonnes of thermal coal. Teck Corporation (Bullmoose property) has a contract to supply 1.7 million tonnes of metallurgical coal annually."

Jan 1, 1983

By C. Desmeules

"Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976.Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen per cent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one-month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March 1980, Sidbec-Normines used coke addition as a current operation.This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port -Cattier pellet plant.IntroductionThe Sidbec-Normines pelletizing plant at Port-Cartier, Quebec, is designed to produce six million ton s per year of oxide pellet s. It is a Dravo-built two-line plant; one line to produce three million s tons per year of blast furnace grade pellets averaging 5.5 per cent silica, and another line of three million ton s to produce direct reduction grade pellets of about 2.0 percent silica.The laboratory pot-grate test program was conducted in 1977 at the British Steel Corporation Research Laboratories in England, with the assistance of J .E. Appleby, consultant to British Steel Corporation (overseas services) Limited.The purpose of that test program was to determine the optimum energy saving cycle and to study the physical and metallurgical effects on blast furnace and direct reduction pellets."

Jan 1, 1983

By Philippe Ribagnac, Bruno Courtaud, Jean-Marie Lambert, Valérie Weigel

Mabounié is a polymetallic deposit in Gabon containing niobium (1.2 wt.%), tantalum (0.03 wt.%), rare earth elements (REE) (1.4 wt.%) and uranium (0.03 wt.%) that are mostly carried by pyrochlore minerals. The classical route for niobium recovery is a pyrometallurgical process that consists of pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF. ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore (Donati, Courtaud, & Weigel, 2014). As for most of the oxidized ore processes, the major impurity is iron (~30 wt.%). Thus, in this hydrometallurgical process, the question arises of the elimination and stabilization of the iron as residue. The iron in solution is ferrous; goethite precipitation seems the most adapted crystalline form. Lab and pilot tests have shown kinetics of precipitation of 6 g.L-1.h-1 at pH 4.5. To reduce the salt discharge, sodium-jarosite form is more adapted, but at pH 2, 95°C only 30% of iron is precipitated in 5 hours, compared to 100% in goethite form at the same time and pH 2, 80°C. Different ways of oxidation were tested, air, pure O2, activated carbon, without drastic effect. The more efficient was ozone use, at room temperature; the kinetics of oxidation is five time faster than the other ways with 30% of sodium removed from the solution.

Jan 1, 2016

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By R. P. Zahn

The need for quantitative mineralogical data to characterize ore types before they are processed is becoming increasingly necessary. Mineralogical data (modal abundances, grain size, liberation/locking characteristics, mineral textures and associations) can provide invaluable information to facilitate the identification of metallurgical issues that may arise during processing of a particular ore. This paper will discuss the use of QEMSCAN analysis in conjunction with bench scale flotation test work to determine metallurgical characteristics for several ore types that will be fed to the Morenci concentrator upon commencement.

Jan 1, 2007

By R. Lepsoe

THE basic products of the Company are lead and zinc. Around 950 tons of these metals are produced each day. In the last decade, the production of by-products has increased to such an extent that they are now nearly as large an operation as that of the base-metals. Of the many by-products, the most objectionable, and up to a few years ago the most useless, was the sulphur. The sulphur comes in the ore from the Sullivan mine. It is in the ore chiefly as lead, zinc, and iron sulphide. By selective flotation, these three sulphides are separated into the lead concentrates, the zinc concentrates, and the mill tailings. These mill tailings contain the bulk of the iron and the sulphur. Of the 6,5CO tons of ore treated per day, about 5,000 tons are wasted to the mill tailings dump, and, while now valueless, will in future years undoubtedly be used as a source of iron and sulphur. There are about 1,500 tons of sulphur and 2,200 tons of iron per day in the tailings, and about 400 tons of sulphur left in the total concentrates. In the recovery of lead and zinc in the pure form, the first step is the roasting operation. Here, most of the sulphur is driven off as sulphur dioxide in the gases. It has always been apparent that this sulphur should be. recovered and utilized if possible. At the same time, this would cure the smoke nuisance. Because, in spite of the low concentration of sulphur dioxide and the fact that it was discharged from stacks at an elevation of 400 feet above the plant, some damage to vegetation close to the plant had been experienced.

Jan 1, 1937

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By A. F. Matheson

"Bankfield Consolidated Mines, Limited, and Tombill Gold Mines, Limited, in the Little Long Lac area, Ontario, mined an orebody that was common to both. The discovery' of this orebody was made by surface prospecting in May, 1932, on Bankfield ground, following an original discovery made in the same manner on the same property on a small reef in Magnet lake in October, 1931. The production from the two mines between 1937 and 1942 was approximately 135,000 oz. gold from about 420,000 tons of ore, an average grade of 0.32 oz. a ton. Production was nearly equally divided between the two properties. Both mines are now closed, the ore exhausted.""The ore is mainly sheared and fractured greywacke and porphyry impregnated by silica and small amounts of metallic minerals. To a lesser extent there are definite quartz veins in the ore zone""(l). The metallic minerals present were principally pyrite, arsenopyrite, pyrrhotite, and native gold .As at other mines in the Little Long Lac area, an elongated, broad, deep trough of folded, steeply dipping volcanic and sedimentary rocks, striking roughly east-west and surrounded by younger granite, is host to the orebodies of the Bankfield and Tombill. In the immediate area of the two mines iron formation and conglomerate bands occur nearby both north and south of an intrusion of porphyry-Cliorite, suggesting repetition of beds and folding. Although considerable drag folding is in evidence, folding on the above scale has neither been proved nor disproved."

Jan 1, 1954

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By R. J. Fruehan

Oxygen steelmaking (OSM) is not only the dominant steelmaking process but defines the structure of the industry. There are a number of myths regarding the future of OSM, which are false. These myths include that the EAF will become the dominant process in the near future, it is less costly to produce steel in an EAF and OSM is a mature technology and no new developments are occurring. These myths are shown to be false. Selected new developments are discussed such as post combustion, recycling of waste oxides, slag splashing and sensors.

Jan 1, 2004