Search Documents

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By T. Feldmann, G. P. Demopoulos

The adsorption of gold complexes on inorganic metal oxides has been mainly discussed in geochemical literature, but it is also of interest to the hydrometallurgical industry. This is so because it could be responsible for valuable metal losses or because it could potentially serve as alternative adsorbent material to activated carbon in certain cases such as from hot and acidic process slurries. This paper constitutes an early investigation into this subject by focusing on the effectiveness of FeOOH, Fe3O4 and Al2O3 as sorbent materials. All tests were done in a batch stirred-tank reactor under atmospheric conditions with synthetic gold(III)-chloride solutions at 23°C and 80°C, in the pH range of 1.6 to 9.0. Detailed kinetic tests were performed at different pH values (3 and 6) on FeOOH and Fe3O4 with solutions having gold concentrations from 5 mg/L to 130 mg/L. The adsorption of gold was found to be best both in terms of kinetics and loading characteristics at 80°C and pH=6. This was explained by a change in Au(III)-Cl speciation from a gold(III)-chloride complex to a gold(III)-chloride-hydroxy complex. By far, magnetite (reagent grade chemical) yielded the best gold adsorption characteristics making it an interesting sorbent material for further development considering that it can be advantageously recovered from slurry streams via magnetic separation. On the other hand, the tendency of gold(III)-chloro complexes to adsorb on metal (hydro) oxides needs to be taken into account to minimize undesirable metal losses in chloride-containing leaching media.

Jan 1, 2015

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By Ed McConaghy, P. LaRochelle

The Ambatovy Nickel Project comprises the development of mine, hydrometallurgical processing facilities and necessary infrastructure in Madagascar, positioning Ambatovy as one of the world’s largest producers of nickel and cobalt from lateritic ore. SNC-Lavalin successfully provided comprehensive Engineering, Procurement, Construction Management (EPCM) services for this major capital project which, apart from its sheer size, scope, and engineering design, represented significant location, infrastructure, labour, environmental and climatic challenges. Today, the project has reached 90% of its nameplate capacity and is in its final performance optimization stage. This paper will discuss the significant project management effort that was required to successfully address the complexity of this major project. It will cover the main project management control systems and the engineering tools and processes used during the detail engineering, procurement, and construction phases to achieve optimum project execution.

Jan 1, 2015

By J. Dennett, M. Faris, M. Antonio, M. Collins, N. Tuffrey, R. Ellenwood, V. Reddy

"In January 2012, AngloGold Ashanti Córrego do Sítio Mineração, with assistance from Sherritt International Corporation, commissioned a new autoclave for pressure oxidation of refractory gold concentrate at the Córrego do Sítio operation in Brazil. Start-up of the plant occurred in a few weeks and enhanced gold recovery was realized almost immediately, with 94% gold extraction achieved in carbon in leach (CIL), compared to less than 70% without pressure oxidation. This paper describes start-up and commissioning of the plant and provides an overview of plant performance over the last five years.INTRODUCTION In 2008, AngloGold Ashanti purchased the former São Bento property from Eldorado Gold, which, along with AngloGold Ashanti’s existing Córrego do Sítio mine, was renamed AngloGold Ashanti Córrego do Sítio Mineração (AGA Mineração). Later that year, the Sherritt Technologies division of Sherritt International Corporation (Sherritt) was contacted to begin batch and continuous pilot plant tests to determine the amenability of the AGA Mineração refractory gold concentrates to the pressure oxidation process. Based on the results of the batch and pilot plant tests, AGA Mineração requested basic and detailed engineering studies to be conducted by Sherritt, eventually leading to commissioning of the plant in January 2012. AGA Mineração’s plant is located in southeastern Brazil in the state of Minas Gerais, near the city of Belo Horizonte. AGA Mineração`s Phase 1 mine plan covers three sites in the Laranjeiras, Carvoaria Velha and Cachorro Bravo ore bodies, and is designed to process 60,000 tonnes of refractory gold concentrate per year to produce 140,000 ounces of gold per year with an 11 year life of mine (AngloGold Annual Financial Statements, 2010). Recovery of gold at AGA Mineração is based on Sherritt`s pressure oxidation technology for refractory gold concentrates (Berezowsky et al., 1991; Collins et al., 2011a; Collins et al., 2011b). This process had previously been applied to the recovery of gold at the São Bento site (Carvalho et al., 1988; de Silva et al., 1989), in a plant that was operational between 1986 and 2007 (Silva et al., 2004)."

Jan 1, 2017

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By Iain Sommerville, Hugh Mountford, Dawid D. Smith, Claude Dube, Brett Hixson

JW Aluminum use lean and Six Sigma techniques to continuously improve their target of reliable, repeatable and reproducible (3R) manufacturing. Six Sigma’s second stage gate, known as "Measure" involves identification and qualifying appropriate measuring systems. Metal quality (inclusions) are known in the industry to be an important element in 3R casting. The measurement of inclusions at JW Aluminum historically depended on outside vendors. In order to establish real time inclusion measurement ability within JW Aluminum, inclusion measurement systems in the marketplace were investigated. The qualification of a MetalVision MV20/20 ultrasonic inclusion analyzer are discussed as well as the subsequent application of the system in melting and casting improvement projects.

Jan 1, 2015

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By J. M. Bowen, P. Wemyss

"Gold losses to natural carbonaceous matter during cyanide leaching have been investigated for over a century. The variation in the severity of the problem from one ore to another has led to a range of different processes being implemented at different mine sites. Most commercial options utilise one or more of the following processes: roasting, carbon pre-flotation, organic blinding, CIL, chlorine passivation, pressure oxidation, biological passivation, elevated temperature CIL, RIL and thiosulfate. This paper provides a background to identify the most appropriate process or combination of processes for a particular ore. It also presents information on how these processes may be implemented, drawing on information in the literature and from current or recent applications at operations such as the following: Stawell, Kumtor, Penjom, Twin Creeks, Macraes Flat, Kittilä, Fosterville, Inata, Carlin, Goldstrike, and Jerritt Canyon. Various process options have been dismissed, or deemed unsuccessful due to limited knowledge available on the strengths and weaknesses of the different options and their implementation. The authors have collectively been involved in flowsheet development and project implementation in four commercial plants that have treated preg-robbing ores.INTRODUCTION Cyanide processing has been the mainstay of gold recovery for well over a century. It is generally a very effective process with over 90% recovery on free milling ores, but complex and refractory ores may only give 0–50% recovery with conventional processing (La Brooy et al., 1994). People have written about gold losses to natural carbonaceous matter during cyanidation for over a century e.g. Feldtmann, (1915). The earliest reports related to African operations, but the issue has since been reported in Canada, North and South America, Australia, Russia and China. The phenomenon is usually referred to as ‘preg-robbing’ dating from the times before the use of granular activated carbon for gold recovery, when gold was lost from the pregnant solution before it could be separated from the leach solids and recovered by cementation. Many excellent reviews have been published e.g. Dunn et al. (2013), summarising the options considered and where they have been applied commercially."

Jan 1, 2017

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By R. L. Bruening, R. M. Izatt, N. E. Izatt, K. E. Krakowiak, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and the demand for higher performance end products expands. Molecular Recognition Technology (MRT) is a green chemistry process that involves use of SuperLig® resins to selectively remove desired metals from a variety of solutions in mining and metals processing industries. Recoverable metal concentrations can range from multiple g/L to mg/L or less. The MRT separation process is based on green chemistry principles and can efficiently produce high purity metal products with minimal waste generation and energy usage. In this paper, applications of MRT to metal recovery and purification in the minor and specialty metals industry will be presented and discussed. Examples will be described involving cobalt, nickel, zinc, rhenium, iridium, indium, germanium, bismuth, and cadmium, as well as removal of lead and iron from process streams.

Jan 1, 2015

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By Jennifer Abols

In July of 2013, Lundin Mining acquired the 2,000 tpd Eagle nickel and copper project from Rio Tinto. The project had been put on hold earlier in the year and construction was approximately 50% complete. Lundin immediately accelerated project activities and by September of 2014 the project was constructed, commissioned and ramping up. The newly commissioned facilities went on to reach design throughput, recovery and product quality targets by the end of the year. This was accomplished ahead of schedule and below budget despite numerous obstacles including the worst winter on record in the past 50 years for the area. What led to the success of the project, and in particular the commissioning phase of the project? This paper takes a high level look back and provides an overview of the methodology used, key issues encountered and lessons learned to answer this question.

Jan 1, 2015

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By L. Lorio, B. Hilscher, P. Nayak, N. Yoon

"Mining has been a staple to technological advancement ever since the dawn of time. By harnessing the different physical and chemical properties that each mining commodity brings to the table, more and more innovation is developed and manufactured. As these non-renewable resources continue to be extracted, the industry as a whole faces a challenge in finding the next economical deposit as well as declining grade at the current operations. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed. This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include one underground and three open pit mines that are precious metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed. The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are also reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS)."

Jan 1, 2017

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015