Search Documents

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

What Bottleneck? ??Resurgence of BC Mining Industry; ??Climate of heightened activity ?Increases pressure placed upon regulatory agencies; ??Current EA and permitting system, when Federal agencies are involved, remains duplicative and inefficient ?not necessarily leading to better decision making; ??Inefficiencies will impederecovery

May 1, 2006

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By C. V. Sibbald

"This paper provides a description of the Highmont copper-molybdenum concentrator from primary crushing through grinding, flotation, tailings disposal and water reclamation. The unique features of the operation will be emphasized.IntroductionThe Highmont property is located in the southern portion of the Highland Valley adjacent to and east of Lornex and about 4 miles south of Bethlehem Copper. The plantsite is at an elevation of 5100 ft.Highmont acquired the property in 1966 and in 1969 Teck Corporation entered into an exploration agreement which contained the option to finance the property to production . A detailed feasibility study of the project was completed in 1971. A positive production decision was deferred at that time because of the prevailing soft copper market and relatively low molybdenum price. The development of a strong molybdenum market in late 1978 and early 1979 led to a re-examination of project economics, and a decision to proceed to production was made in April 1979.The Highmont ore zones occur adjacent to and on either side of an east-west-trending quartz porphyry dyke. The two major zones , the east and west pits, contain 122 million tons of ore assaying 0.27070 Cu and 0.029% Mo. Chalcopyrite, bornite and molybdenite are the minerals of economic interest. Chalcopyrite is the predominant copper mineral. Mineralization occurs primarily along fractures and is zoned according to fracture density. Some pyrite is present, but for the most part it is outside the ore zone. Surface oxidation is shallow throughout the orebody.Wright Engineers Limited were responsible for the major part of the engineering design. Site construction, which began in the spring of 1979, is under the direction of Commonwealth Construction. The first concentrator line is scheduled for completion late in 1980, the other for early in 1981."

Jan 1, 1981

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By John C. Taylor

"The non-ferrous pyrometallurgical industry has been under extreme pressure since 1980 and significant changes are taking place, principally in the copper, nickel and lead industries. This paper reviews some of these changes, particularly with respect to smelter capacity, major technical trends, and the industry's response to increased energy costs and environmental constraints.The Canadian metal mineral production for 1985 has been estimated at a value of over $8 billion, of which half is derived from copper, nickel, lead and zinc production. It is in our national interest that the Canadian industry remain competitive in the world market and continue its traditional contribution to the Canadian economy. IntroductionPyrometallurgy by definition requires energy, usually in the form of fuel, and produces process gas streams which can no longer be discharged directly to atmosphere in most countries. While the industry has been under varying degrees of pressure over the past fifteen years, it is just since the early 1980s that major changes have taken place, due, to a large extent, to an oversupply on the primary metal markets and depressed prices. These factors, combined with a surge in the price of oil, have resulted in some trends developing which must be recognized by those in the industry who plan to be in operation and competitive in the next decade.Although the value of Canada's mineral production, in terms of constant dollars, has decreased by more than 35% over the period from 1980 to 1985, the bulk of this production is exported and the industry still makes a significant contribution to the Canadian economy."

Jan 1, 1988

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By Brendan Parker, Tyron Rees, Steven Hart, Abba Manesh, Ian Mcgaffin

"In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit.This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes"

Jan 1, 2012

HIGH LAKE PROPERTY --HISTORYHISTORY -19501950??s ??Kennarctic Exploration discovers Exploration sulphides (A/B & (D Zones) at High Lake during helicopter reconnaissance exploration program.- -1991 93 Aber signs agreement to earn in to the High Lake Property from Kennecott. 63 holes drilled, primarily testing the known deposits. -2001 Wolfden purchases 100% interest in High Lake from Kennecott and Aber -2002 Wolfden performs helicopter borne TEM Survey over the High Lake Greenstone Belt. -2003 West Zone was discovered following UTEM & Gravity Surveys (performed by Teck Cominco ) over an airborne anomaly approx. 1km west of the known deposits. -2004 Wolfden awarded Bill Dennis Prospector of the Year

May 1, 2006

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006