Search Documents

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By P. B. Queneau, Peter V. Avotins, Lauch F. Farris

"The Lang Bay germanium property is a carbonaceous sandstone deposit outcropping near the Pacific coast, 100 km north of Vancouver. The germanium-bearing seams are up to 5 m thick. Where one such seam outcrops, it averages 50 to 60 g Ge/tonne. Drill core analyses have shown considerably greater concentrations of germanium at depth. Additional drilling to establish continuity and grade of the germanium-b earing strata is scheduled for 1986. The germanium occurs in association with lignite, which makes up 1 to 2% of the seam. American Cyanamid Company engineers have developed a proprietary flotation reagent effective for concentrating the germanium rich vitrain portion of the Lang Bay lignite. Ongoing laboratory studies are developing procedures for further upgrading and refining of this germanium. This paper outlines progress made by Fargo Oil Corporation on Lang Bay geology, reserve estimation, mine planning, ore dressing, refining, and economic evaluation.IntroductionIn 1871, Mendeleyev specula ted on the properties of a ""missing"" element between silico n and tin on the periodic table. The discovery of germanium fifteen years later proved the Mendeleyev predictions to be remarkably accurate. Almo half a century later, the pioneering work of McCutcheon of Eagle-Picher led to production of germanium dioxide from Oklahoma zinc smelting residues. Demand for the element surged due to development of the Ge02 diode rectifier during World War II, followed by development of the transistor in 1947. The chief commercial sources for germanium during the following two decades were the Cu-Zn mines in the Congo and the Zn-Cu-Pb mines of Tsumeb in Southwest Africa. The germanium was chemically combined in complex Cu-Fe sulphides (germanite and renierite), from which the element was recovered either by leaching the selectively roasted sulphide, or by direct fuming of GeS(I). Although these deposits have reportedly been depleted (2), new deposits of renierite have been discovered in Zaire. Alternative sources of germanium are therefore being sought worldwide for use in infrared optics, semiconductors, fibre optics, and catalysts. One such source is germanium-rich coal (2)."

Jan 1, 1986

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By Fred A. Webber

STEEL ROPE WIRE is one of the more specialized commodities among the many grades of highcarbon steel wires. In its production there are many metallurgical aspects of interest from the steelmaking on through the final stages of wire drawing. We produce rope wire in an integrated mill com prising all the operations from the blast furnaces to finished wire drawing in the wire mills. Steelmaking is carried out with close control on hot metal, selection of scrap, and fluxing materials. The basic open hearths are of 170 tons capacity. Steel is teemed into 19 1/2 in by 19 1/2 in big-end-down molds and is hot-topped with the use of clay refractory hot-tops. The weight of this ingot is 6,900 pounds. All high -carbon steel ingots are charged hot into the soaking pits and are then rolled through the blooming mill in 16 p asses to a bloom ax~ in. by 41/2 in. and approximately 65 feet long. Necessary bottom and top crops are taken on the bloom as it passes from the blooming? mill to the billet mill. The still hot bloom is continuously rolled through the billet mill in . 5 passes to a 2 3/8 in. square. Billets are cut to 32 feet in length by a flying shear and then allowed to cool on the hot bed.

Jan 1, 1957

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By H. Kim

"IntroductionThe Hat Creek coal field contains low-grade coal deposits which are the thickest in the world. The diamond drilling and geophysical surveys conducted by B.C. Hydro over the last six years have indicated in excess of 2 billion tonnes of sub-bituminous to lignitic coal. The coal field is in the Interior Plateau Dry Belt, about 240 km northeast of Vancouver, and contains two explored, nearsurface coal deposits amenable to surface mining (Fig. I). The No. I deposit contains approximately 740 million tonnes of coal at 17.71 MJ / kg, or 7,600 Btu/lb, at 34.82% ash and 24% moisture. The No. 2 deposit to the south contains appreciably more coal resources at somewhat lower grade, but it has not been explored so extensively because of its higher stripping ratio. Therefore most of the exploration activities to date have been directed toward the development of the No. I deposit. The No . I coal deposit has been selected as the source of fuel for a proposed thermal powerplant to be built about 5 km east of the deposit. The purpose of this paper is to summarize the data obtained from the diamond drilling and the geophysical logging in the No. I deposit between 1974 and 1979. An attempt is made to explain the depositional environment of the Hat Creek coal measures. Because the understanding of the depositional environment in.a particular basin is essentially an evaluation of all the geologic properties of the area, the available geological information in the No. I deposit has been compiled on the basis of consistent criteria. This includes data on the lithology of the coal measures, thickness and areal distribution of the elastic sediments, and on the changes in the megascopic stratigraphic profile based on geophysical correlation. The palynopetrographic relationship and detailed sedimentological aspects are not examined in this paper. Such studies should provide important information relating the causal vegetal and chemical responses of the coals to -environmental changes. Extensive deposition of surficial materials during de-glaciation left most of the area of the Upper Hat Creek Valley devoid of bedrock exposures. Structural and stratigraphic features are hidden beneath glacial deposits and/or post-Eocene volcanics. As a result, the geological interpretation of the Hat Creek coal basin has been based primarily on drilling and geophysical data. Because of this, any explanation of the depositional environment details is tentative until the deposits are stripped for development."

Jan 1, 1985

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By Harry V. Warren

THE Dolly Varden Mine is situated in the Kitsault River valley, eighteen miles from the head of Alice arm, in the Nass River mining division of British Columbia. During the years 1919-21 it was operated by the Taylor Engineering Company, Limited, and produced 1,300,000 oz. silver from about 36,000 tons of ore. The ore was transported by narrow-gauge railway to Alice arm, and shipped to the smelter at Anyox for treatment. During recent years, a small quantity of high-grade ore has been extracted by leasers and shipped to the smelter at Tacoma, Wash. Unfortunately, the bonanza ores which occurred near the surface did nor persist to depth, and two hundred feet below the exposures only rare and unimportant patches of ridi ore have been found. Two opinions exist as to the origin of this rich silver ore. One, advanced by V. Delmage (1, 2), is that the ores are hypogene, and the other, by G. Hanson(3, 4, S), is that the ores are the result of supergene enrichment. It is true that Dolmage first advanced his view that the ores are primary because they appeared to be analagous to Premier ore, which he had studied in detail and which he considered to be primary. The present authors have had access to excellent suites of material from both mines and consider the comparison well taken, the only essential mineralogical difference being the presence at the Premier mine, in addition to the silver minerals, of gold and electrum. Although the arguments put forward by Delmage have, in the opinion of the authors, never been refuted, nevertheless R. P. D. Graham(6), in a reference to the mine published in 1924, describes the ore as of supergene origin, and since then nobody appears to have challenged this statement. Indeed, in 1935, Hanson re-affirmed his earlier conclusion(5).

Jan 1, 1942

By J. D. Christian

WHEN mining development began in the Kirkland Lake camp, twenty-five years ago, there was very little information obtainable from surface showings as to the nature of the ore deposits. A length of almost a mile of the main 'break' lay under the south arm of the lake, and elsewhere most of the outcrops were covered with glacial drift. Shafts were sunk on ore-bodies of uncertain value, either on the outcrop of the veins or-because of the lake to the north-in the south or hanging-wall. In the second year of the camp's development, the Great War broke out and retarded progress for its duration. He would have been a real optimist who, in those early years, could have foreseen mining at depths of more than a mile.

Jan 1, 1939

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By R. C. Rowe

THIS paper is an endeavour to analyse the ideal and practical functions of government technical mining services, and their relationship to the National Domain, as well as to one another. its spirit is not critical, even though at times it may appear to besoin fact. It is a serious effort to divert a trend in public thought which delights in calling itself practical whereas it is really merely short-sighted. The author refers particularly to the idea that governmental research is a luxury which should be curtailed in the interests of economy, and turned over to private enterprise or the provinces. In order that we obtain the proper perspective of the question, it is advisable to indulge in a little history. In the year 1842, the Geological Survey of Canada was formed under the guidance of William (later Sir William) Edmund Logan. The literature on the founding and history of the Geological Survey of Canada is extensive, and therefore it is unnecessary to go into detail here regarding it. It might be mentioned, however, that the Geological Survey of Canada is only seven years younger than the Geological Survey of Great Britain (founded in 1835), and is only exceeded in age on the American continent by the State Geological Surveys of New York, Pennsylvania, Massachusetts, and Michigan, which were founded between 1833 and 1836. In 1877, the Geological Survey became a permanent government institution as a branch of the Department of the Interior. It should be noted, however, that the Director of the Survey ranked as a Deputy Minister and reported direct to the Minister. This continued until 1907. In 1886, the Mineral Resources and Statistics Division of the Geological Survey was formed. Some years later, the Canadian Institute of Mining and Metallurgy (then the Canadian Mining Institute), backed by the mining press, began to agitate for the establishment of a Dominion Department of Mines, and in 1907 such a department was founded by the Geology and Mines Act of that year, with a separate Cabinet portfolio for the position of Minister of Mines.

Jan 1, 1939