Search Documents

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By A. M. McKim, J. S. Ambler

"The iron ore of the Scully Mine is upgraded from 36 per cent Fe to 66 per cent Fe through single-stage crushing, wet autogenous milling, sizing by vibrating screens and two-stage spiral separation, followed by a process in which the concentrate is dried and then further improved by high-tension separators. The capacity of the concentrator is 17,000 long tons of concentrate per day. Discussion of the operation will recognize the special problems encountered in handling preponderantly fine ore, relate issues of interest regarding wear and review mechanical innovations found to be advantageous at Wabush. The modern trend toward big equipment, thoroughly instrumented, has been the theme of design. Effects on availability must be a consideration in this choice, and sectionalizing of circuits to minimize these consequences is as important as streamlined maintenance."

Jan 1, 1969

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By Chris Dougherty

"This presentation will provide a demonstration of the methodology used in designing a modern shaft and hoisting plant utilizing a review of the challenges faced and solutions delivered for the Elk Creek Superalloy Materials Project (Niobium/Scandium). The development of the design required the review of complex hydrogeological conditions, mine production requirements, demanding capital expenditure (CAPEX) limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group (including Nordmin Engineering Ltd.) (Nordmin) was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. INTRODUCTION The Elk Creek Project, owned by NioCorp Developments Ltd. (NioCorp) presently, will become Nebraska’s first underground metals mine, built to access the Elk Creek Niobium/Scandium deposit. The development of the design for this facility required the review of challenging hydrogeological conditions, mine production requirements, demanding CAPEX limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. This paper will review the challenges faced, and solutions arrived at in a demonstration of a methodology used in designing a modern shaft and hoisting plant. THE CHALLENGES Nordmin became involved in the project in 2015, invited by the Feasibility Study Consultant to provide input on estimating and layouts for the new operation. Many of the fundamental decisions regarding mining methodology, water handling and production strategy had been made, and the scope of Nordmin’s involvement was very limited in this first engagement. Following submission of that study in late 2017/early 2018, Nordmin had opportunity to discuss the overall effort, and its many assumptions and challenges, with NioCorp’s project team. The dialogue quickly identified several significant opportunities to improve the project construction schedule and costs along with the mine production profile and operational approach while reducing project risk."

Jan 1, 2019

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

Although Canadian bentonite is competitive in quality for most uses, it has not been accepted for the pelletizing of iron ore concentrates. In 1962, Canada consumed about 10,000 tons of imported bentonite for this use. By the end of 1965, the planned domestic consumption for this purpose alone will probably be more than 100,000 tons a year, valued at about $3 million. Consequently, a challenge exists for the establishment of a Canadian source of high-quality bentonite for pelletizing. Such a bentonite would also be suitable for the two other major applications -well drilling and foundry use. Brief mention is made of such topics as the identification, 1noperties, occurrences, exploration, applications, technology and laboratory testing of this clay. In particular, the type of bentonite in demand, the geological horizons warranting exploration, and simple preliminary test methods are discussed.

Jan 1, 1964

By Zoltan F. Oszter

The design of belt conveyors is a well-known procedure and related formulae can be found in any handbook dealing with materials handling. Belting and conveying equipment manufacturer's catalogues and design manuals offer a wide range of detailed information which can be applied to most of our conveying problems. The aim of this paper, however, is to investigate the design of a specific type of belt conveyor, namely the long horizontal, or nearly horizontal, type. (The undulating type, with moderate lifts and drops, can also be included in this category.) Most of the long overland conveyors carrying ore from pit to processing plant, or those carrying over-burden to the disposal area, fit this description. A critical appraisal will show that reasonably accurate results can be obtained when tl1e familiar horse-power formulae are applied to this type of conveyor. The progress and new developments in the design of belt conveyors, which have resulted from the extensive research done in the past decade, will also be explored.

Jan 1, 1962

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation's entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"Abstract -The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and fine­ grained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. AU are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-rnassive pyrite + chalcopyrite are known.The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to host polymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit Jacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, Jess deformed volcanic­ sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By E. Godin, M. Rigaud, S. C. Panigrahy, I. Malinsky

"RésuméDes boulettes de concentres d'hématite spéculaire à basse silice ont été produites en substituant la bentonite par de la tourbe, adéquatement traitée, additionnée d'une faible quantile de soude caustique durant le boulettage. La réductibilité de telles boulettes et leur gonflement pendant la réduction ont été évacues, en utilisant quatre mélanges gazeux différents, formes de H2 - CO - N2.L'influence du pouvoir réducteur du gaz utilise, sur le gonflement des boulettes, à été mis en évidence. Quelles que soient ces conditions réductrices, les propriétés mesurées sur les boulettes liées a la tourbe sont comparables aux propriétés obtenues avec des boulettes traditionnelles liées à la bentonite.ABSTRACTAdditions of peat moss and small quantities of NaOH during balling of low silica specular hematite concentrates have eliminated the need to use bentonite as a binder. The reducibility and swelling of such pellets have been evaluated using four different gas mixtures, consisting of H2 - CO -N2. The influence of the reducing power of the gases, on the swelling behaviour of pellets has been documented. Under the different reducing conditions, this new type of pellets exhibit properties similar to the ones obtained using bentonite."

Jan 1, 1987

By J. G. Kelly

"IntroductionOver the past twenty-five years of improvements to scooptrams In the Ontario Division of Inco Ltd., records indicate that on average, an 8 yard capacity machine at 80% availability will load, haul and dump about 100TPH from an average stoping area. This, essentially, means that Inco mines are limited to 2000 TPD as an approximate maximum production cap per minute. Some of the improvements made to scooptrams over this period have been:• dry disc and oil immersed brakes on larger loaders;• to replace air over hydraulic systems;• modulated shift transmissions;• greater breakout and tramming capacities by using larger engines and buckets;• operators' compartments have been enlarged and better seats,• joystick controls and air-conditioned cabs have been utilized'• major cost savings have been realized through tire maintenance improvements; and• major savings, safety improvements and increased ore recovery by using remote controls.After reciting the improvements listed above, and the list is by no means exhaustive, it is quite obvious that scooptrams are a mature product and that major design or performance improvements will not occur in the futre. Any futher improvements will be incremental in nature. Loading, hauling, and dumping with scooptrams is a batch process and as such is limited in its total output.Continuous Load/Crush/Convey Systems:In order to improve productivity, a radical new system was required. The target was 2000 tons per shift. In 1984, to meet the goal, Inco acquired the rights to a contiunous loader from Canadian Mine Services. Inco made modifications to the original prototype machine, such as: (I) conversion from rail mounted to crawlers for increased mobility; (2) a hydraulic cooling system was added; (3) flight bars were changed from cast to forged; (4) motor horsepower increased to 200 hp from 150 hp. Emerging from these modifications came a machine known as the CL-looo Oscilloader (Fig. 1).The CL-looo Oscilloader is an electric hydraulic 35-ton machine which is crawler mounted and has a drawbar pull of 30 tons. It has an adjustable frequency, oscillating lip which simulates the digging action of a manual .shovel. This action agitates and lifts the muckpile enough to allow it to settle by gravity onto the chain and flight conveyor table which then removes the ore to the tail end for discharge into either a crusher, a conveyor, a truck, or a combination of these.Late in 1985, six oscilloaders were fabricated and put into Inco mines for field trials. At Creighton Mine some early field trials were conducted with a rail mounted continuous loader loading directly into 140 cu.ft. Granby cars. Much of the field testing was in VRM drawpoints with the Oscilloader loading into 20-ton trucks or into Teletrams . At Levack Mine, by puttmg the truck on remote control, it was possible to have the operator run the Oscilloader and load his own truck (Fig. 2). At McCreedy West Mine, Copper Cliff North Mine, and Copper Cliff South Mine, the Oscilloaders discharged directly into 26-ton trucks."

Jan 1, 1988

By S. C. Tadolini, J. M. Goris, J. L. Gallagher

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines (USBM), researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road entries in a western U.S. coal mine. With the cooperation of industry, methods were developed to install and evaluate cable supports in a tailgate area using traditional resin cartridges. The cable-bolted areas successfully maintained roof support throughout the developed entries. Cable supports have replaced wood cribbing as secondary support in the bleeder entry system and have minimized or eliminated the use of cribbing in the longwall tailgate entries. This paper describes the theory, application, and advantages of cable supports and presents some mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1999

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994