Search Documents

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By S Vink, V Nanjappa, C J. Moran

Poor quality water resulting from interaction of surface run-off with saline mine spoil and soils can cause significant problems for water reuse on mine sites. Not only can this saline water lead to machine corrosion and increased maintenance costs, but may cause detrimental effects on the environment. Determining the geochemistry of mine spoil, and the likelihood of salt dissolution during rainfall events, may aid in more effective mine site management of water. Spoil samples were taken from three areas of the German Creek mine site, situated in the Bowen Basin coalfield, Queensland. Samples from two undisturbed areas on the lease were also collected for comparison. Analyses were performed using a variety of laboratory techniques: leaching tests, effective cation exchange capacity determination, X-ray diffraction, clay quantification, and total organic content determination. Results show that dissolution of surface (top 2 cm) salt minerals from spoil areas is an important contributor to surface run-off salinity during rainfall events. Equally, ion exchange with clay minerals appears to be a significant source of elevated ion concentrations in run-off waters. Findings from the undisturbed areas show undetectable quantities of salt mineral species, resulting in waters with low ion concentrations. More generally, monovalent cations (sodium, and to a lesser extent potassium) appear to be derived from dissolution of salt precipitated whereas divalent cations (calcium, magnesium) are more likely to be sourced from exchange reactions with clay minerals. Incorporating knowledge about the mechanism of cation mobilisation from spoil with the spatial distribution of spoil properties and understanding of the dynamics of water quality variations on the site will aid in development of integrated water quantity and quality management strategies.

Jan 1, 2009

The karst water system in Han-Xing District is charaterised by heterogeneity in karstification and permeability of the limestone aquifer, unsteady flowing of the groundwater along karst runoff zone system, periodic recharge related with the periodic precipitation, and concentrative discharge of the groundwater in the form of karstic spring groups. The basic law is that the quantity of the water is very large during waterflood period and rather small in dry period, which has brought about difficulties and contradictions in mining and water supply. The measure to bring the karst water under control must be based on the principle of comprehensive ways and on the systems engineering method. Macroscopiclly, it is the reasonable countermeasure to retain surface water in the upstream section of the karst water system and to strengthen infiltration in the midstream section and to combine exploitation and utilization of the groundwater with water protection and mine dewatering in the area in which mines are distributed.

Jan 1, 1988

By Broome A

In a technologically oriented industry, it is important to understand and apply technology very consciously to create competitive advantage. Technology is not an activity which is simply restricted to CSIRO or the research and technology department. Technology improvement is a part of everyone's role. It is a way of life - the technology facet of continuous improvement. For this reason, The AusIMM has organised this Travelling Technology Forum - a series of presentations about automation in mining. To make the message more accessible, The AusIMM had originally planned to take the Forum to four regional mining centres: Mackay/Townsville, Singleton, Burnie and Kalgoorlie, but only one seminar was held, ie at Singleton in March 1997. Seminars at other locations were cancelled because of insufficient registrants. The presentation by Andrew Logan of BHP Cannington was not available for the Singleton forum. The aims of the forum were: ò to heighten awareness of the key technologies and their impact in the minerals industry in the medium term; ò to foster creative thinking; ò to encourage people to broaden their technical and commercial skills and develop individual networks and linkages based on an interest in these key technologies; ò to share information on the application of these technologies in the industry; ò to promote an enhanced appreciation of the need for an innovative culture; and ò to encourage staff to consider post graduate courses in technology management. The AusIMM wanted to not only raise awareness about `automation in mining' issues, but also to get technology in a more general sense back onto `centre stage'. The Forum was generously supported by CSIRO, Western Mining Corporation Ltd, BHP Coal Ltd, Aberfoyle Limited, Goldfields Ltd, Novacoal Australia Pty Ltd, Pasminco Ltd, and RGC Limited. The program was endorsed by the Centre for Mining Technology and Equipment (CMTE). Copies of the full papers are available from the authors, see `References'.

Jan 1, 1997

By Boehme PW, Gregory OR

The results presented here show quite definitely that in the system investigated the intensity of dispersion is enhanced by switching the flow entry from bottom to sides of the packed trough. Since there is no reason to suppose that this would not be true generally then it is not surprising that the blast furnace dispersion data of Standish and Polthier lie above the data for packed columns with bottom fluid entry. In fact, on the basis of the present results, blast furnace dispersion results can never equal standard packed column behaviour but must always be above these. The result that the intensity of dispersion in the trough model is higher closer to the side ports than away from them is at variance with that of Standish and Polthier blast furnace results. Aside from the obvious structural differences between these two systems, it is thought that the presence of raceways and the tortuous path of the gas flow in the furnace may provide an answer. Clearly this is an important difference in the behaviour of the two systems and further investigations designed to clarify the position would have significant practical value. This would also give an indication of how the furnace D/ud values may be decreased along the whole height - assuming of course that this result gives the best overall performance of the furnace. However, there is to date no knowledge whatsoever about this aspect of blast furnace Technology.

Jan 1, 1975

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

In presenting size analysis data, one has the choice of various graphical techniques; each no doubt has been developed to highlight a particular aspect of the data. A frequency size distribution plot is used quite extensively to illustrate the importance of the finer size particles in iron ore granulation. However, the basis for such a plot is often not appreciated. As a result, cases of incorrect use can be cited. The aim of this paper is to extend the work of Alien (1981) and to provide, using examples and figures, a basic understanding of the implications of the various size distributions. A simplified method of presenting sizing data on a linear scale graph paper is presented and recommended. This involves a simple construction of a histogram of mass fraction versus particle size (in geometric progression).

Jan 1, 1992

North Broken Hill Limited came into prominence as a producing mine at· the commencement of the present century, when a great many of the disabilities experienced in earlier mining operations th:rough lack of adequate stope filling had been overcome.The northern or narrower ore-body was first mined in the upper levels and, in the early stages, no great difficulty in mining was experienced. In depth, under the influence of its northerly pitch,. the wide southern ore-body entered the North mine between the 400 and 500-ft. levels. Owing to its flat dip and the relatively weak nature of the hanging wall and footwall, the value of close filling was recognized and this policy has been followed throughout the life of the mine. This feature undoubtedly contributed to the freedomfrom "creep" action to which some of the older mines had been subjected.The Broken Hill lead-zinc-silver ore-bodies occur as well defined replacements of favou:rable horizons, in intensely folded Pre-Cambrian sedimentaries. In the North mine two main replacement zones occur, the Gre being found where the beds are involved in a certain set of minor folds. The resulting ore-bodies are roughly elliptical in cross-section, the long axis of one being north-east of, and somewhat offset from the long axis of the other. The ore-bodies pitch eastwards at 40° and dip northwards at 60° in a fairly regularmanner. The southern Ore-body has an average length of 700 feet and an average width of 90 feet with a maximum width of 230 feet, whilst the nonhern ore-body on the lower levels averages 500 feet long and 40 feet wide.

Jan 1, 1940

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

The use of the heavy media cyclone (HMC) Separation process for the treatment of ores in a particular size range is comparatively new to Australia. The paper describes briefly the principles of HMC operation. Reference is made to early development work, the pilot plant trials and the acceptance of the technique as a mineral dressing process. The Mitchell Cotts pilot plant at Amdel is described briefly and the results of test work on this unit for the processing of a wide variety of ores and ore types are given. Comments are made on the ob- jectives aimed at in the investigation and results are discussed with particular reference to behaviourial differences between ore types. The process is easy to operate, possesses a high capacity-to-unit-size rating and is capable of a high degree of flexibility. Further developments such as specially prepared and graded media for specific applications, automatic media density control and regulation of media consistency by the use of surface ac- tive agents and polymers have increased versa- tility and sensitivity of control to the point where products differing by as little as 0.02 of a specific gravity unit can now be separated with ease.

Jan 1, 1973

By Thompson D, Burgess G. C

Subsequent to large scale trials in 1987, the installation of a submerged lance Sirosmelt furnace system was approved in late-1988 for the cupellation of retort bullion to dore silver. Commissioning work commenced in June 1990. During the process air is lanced into a molten slag bath contained in a cylindrical vessel to rapidly oxidise the granulated feed bullion from 15 - 25 per cent silver to rough dore grade. The process is now an integral part of the Precious Metals operation replacing the first stage reverberatory cupellation furnaces to achieve productivity improvements, lower silver inventory and increased silver Recovery.

Jan 1, 1992

Simple quotation of quantities of coal reserves neglects the relationship between qualities of coals and their efficient use. If exploitation of a deposit is contemplated, its life expectancy can be deduced only if its reserves are estimated according to the coal user's technological standards. A wide range in properties will satisfy a steaming coal, whereas a high vitrinite high rank coal would be preferred for coking and a low inertinite low rank coal for conversion. In competitive trading the buyer's commercial specification may require weighing against the producer's practical ideals, especially when beneficiation is critical. Differentiation of grades in quality of a deposit provides an intelligent understanding of the economic importance of the deposit. The Wongawilli seam of the New South Wales Southern Coalfield exemplifies the effect of quality criteria upon the extent of in situ, recoverable and marketable classes of economic reserves. Effective management of a deposit will result from simultaneous quotation of coal qualities and quantities in a statement of its reserves.

Jan 1, 1979

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

Having worked as a consultant for most of his 40-year working life, mostly as a mineral property valuer, the author has seen many poor valuations. Most were valuations of exploration tenements where the selection of the rather subjective, but necessary, geological inputs raised the main concerns. Those valuations involving iron ore prospects raise particular problems due to the special characteristics of such deposits. Iron ore is more like an industrial mineral rather than precious or base metals and Reserves are determined not by a traditional cut-off grade but by customer specifications. This is intended to be an overview/keynote paper on the current state of the growing (yet consolidating) Australian Iron Ore industry. It has now moved beyond Western AustraliaÆs æPilbara Big TwoÆ of Rio/BHPB (with the emergence of the irrepressible FMG and Hancock Prospecting) to include the YilgarnÆs æMidwest ManyÆ (including US re-entrant Cleveland Cliffs through Portman) and projects in other States. Ore types have moved from haematite Brockman to martite-goethite Marra Mamba (including the RobeÆs mesas and below water table Yandicoogina CIDs) and magnetite ore types. There are DSOs and secondary process feed. Mineral valuers have to reflect today upon these and many other determinants of value when choosing the most appropriate methodologies to adopt when technically assessing and valuing exploration tenements containing iron ore. Set against a frame work of the JORC Code (2004) and VALMIN Code (2005), the general valuation issues involved in using the cost methods (eg multiple of exploration expenditure), market methods (eg comparable sales, rules-of-thumb and joint venture terms) and income methods (eg synthetic discounted cash flow (DCF)/net present value (NPV) modelling) are discussed. Relevant factors when valuing iron ore properties are discussed, eg ore type, lump/fines ratio, stripping ratio, water table, impurities and grade, particularly the JORC confidence category of the identified mineralisation. Remoteness and access to existing rail infrastructure is a key consideration.

Jan 1, 2007

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

By Giannini L. M

Optimisation techniques, based on the block model, for solving the optimum pit limit problem were discussed in an earlier paper. Of the available techniques the one based on graph theory proved to be the most attractive. In the graph theory model the vertices represent blocks and the arcs represent the mining restrictions. For large ore-bodies direct application of the graph theory method poses considerable computational and storage problems. Techniques for easing the computational effort by reducingthe problem size were introduced in an earlier paper. Further, significant computational savings can be made by exploiting the structure of the graph. This is done by building the graph up level by level and successively applying the graph theory algorithm to reduce the number of blocks. In building up the graph in this way one needs what is called a "search pattern" to indicate which arcs are to be added as new vertices are introduced. Moreover, as it is essential to keep the number of arcs to a minimum it is necessary to establish a "minimum search pattern".The problem of determining minimum search patterns for any block model and for any wall slope restrictions has not been considered in the literature.The objective of this paper is to present a complete solution to this problem and to discuss, through typical case studies, the application of the associated software developed.

Jan 1, 1988

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

By B R. Bittencourt, D A. B Pasin, D Pi

Three main genetic types of hematite can be recognised at Quadrilßtero Ferrffero (QF): Micaceous or schistose hematite derived by metamorphic/metasomatic process during regional metamorphism, increasing eastward, formed under temperatures ranging from 250¦C to 500¦C in CO2-rich aqueous carbonic, high- to medium-salinity fluids. Hematite in shear and mylonite zones, showing a wide variation of fluid and temperature conditions, between metamorphic and hydrothermal conditions. Deformed quartz-specular hematite veins formed during the late phases. Hydrothermal, compact and isotropic hematite developed during a brittle-ductile regime, forming the cement of the boudinage-kink breccia and jacutinga-type of gold mineralisation, under temperatures ranging from 80¦C to 140¦C in aqueous, low- to medium salinity, oxidant fluids, resulting from the interaction of meteoric and metamorphic/metasomatic fluids. Quartz-carbonate-sulfide veins were formed slightly later, through reducing fluids.

Jan 1, 2005