Search Documents

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By Orr T. O H, Hodkinson I. P

The Mount Leyshon breccia complex is located on an east-west trending contact between Cambrian metasediments (Puddler Creek Formation) and the Ordovician Mt. Leyshon granite, within the Lolworth-Ravenswood block. Detailed mapping of basement, breccia and igneous unit geometries, crosscutting relationships and resolution of complex chronological relation- ships indicates that the Mt. Leyshon breccia complex should be reinterpreted as a number of intrusive igneous and breccia phases. This is in contrast to a previously published account of a largely extrusive geological setting. A complex structural history dominated by strike-slip faulting is preserved within the basement units and is responsible for controlling the location and geometry of the breccia complex. The breccia complex has been divided into brecciated "basement", "main pipe breccia" and an "interactive magma/breccia sequence". Main pipe breccia (the most voluminous unit within the complex) has been re-interpreted as an intrusive breccia, rather than an extrusive or vent fill as previously proposed. This is based on the following evidence: 1. the facies characteristics of the main pipe breccia, 2. the presence of a progression from cohesive basement through to mixed breccia, 3. minor basement block rotation during breccia complex formation, and 4. the partial structural control on the main pipe breccia. No unambiguous evidence exists for pyroclastic facies, although the fine breccia variant commonly contains "accretionary structures", very similar in appearance to those formed during pyroclastic processes. In view of 1. above, they are interpreted to be the product of particle accretion during upward movement of fragmental material, although an origin due to altera- tion cannot be completely discounted. heir occurrence in the main pipe breccia indicates that their presence within a rock unit is not necessarily diagnostic of nvroclastic nroeesses.

Jan 1, 1991

By P Benjamin, H Bohannan, C Farr

Geoffrey Blainey's historical account of the mining activity on the west coast of Tasmania, æThe Peaks of LyellÆ documents the changes over 130 years of activity in the region. Commissioned by the Mount Lyell Mining and Railway Company, emphasis is placed upon the development of the Mount Lyell Mine in Queenstown. Chapter 19 æWidening HorizonsÆ details the review the Mount Lyell Company undertook in 1904/05 to ensure the future of the operation, following the pessimistic outlook regarding diminishing reserves and poor grade ore. The analogies documented between the Mount Lyell Company at that time, and Gold Mines of Australia 90 years on are remarkable, with both companies demonstrating a commitment to the Mount Lyell area through active exploration, the proactive search for alternative technology and the recognition of the valuable human resource. As Blainey writes (Blainey, 1993), æwith its expanding chemical works, its huge Tasmanian mines, its railways and smelter, its coke works and its mine crusade, Mount Lyell was probably one of the nation's five great industrial companies in 1906 or 1907. This brief phase of industrial and mining expansion had its seed in the threat of extinction . . .Æ After a number of reprieves, the Mount Lyell mine did stop production in 1994, but that only provided an impetus for a review and rebirth.

Jan 1, 1998

By M Schmid

German hard coal mining operations have decreased for more than 40 years. Current political decisions are leading to a discontinuation of subsidised black coal mining by the year 2018. This decision will, however, be reviewed once again in the year 2012. The enormous increases in productivity, which were achieved in previous years, have so far not led to an achievement of market requirements. Coal mining at depth of more than 1200 m in multiple seam environments is not yet competitive in global comparison. In 2008 the 24 faces left in eight mines produced about 20 million tonnes of usable steam coal. Management and the workforce will be reduced in parallel; from today until 2012 by more than half. The average age of personnel is increasing dramatically and nearly no new personnel are recruited. With this background in mind, increasing continuously coal mining productivity becomes more and more difficult. Above all, this goal was reached by mechanisation, then by increasing the mining machine power and then by enhanced machine control systems. The first attempts to automatically operate full face equipment from above ground were in the early 1980s. After successful automation of the face equipment, the emphasis is now on mine logistics. Autonomous monorail transport was introduced and tested in 2007. Since the development rate of machine improvements has its limits, the focus is on the full interaction of the total production system. Here information technology (IT) becomes important; the driver for more productivity. Actual developments aim for the complete and general homogeneous IT infrastructure both above ground as well as underground. The explosive environment needs high level investments in safe technology, eg access points for WLAN and fibre optics for underground use (ATEX certification). New technology availability also drives the enhancements of management and process control systems. Innovations in the mining industry often comprise technology advances through the adoption of well-known technologies. With virtual reality (VR) teaching and training systems advanced computational instruments, both in software and hardware development, were applied in the German coal mining industry for ten years. Widening lists of applications as well as the encouraging achievements show the economical benefits of investing in virtual reality technology both for teaching and training and for knowledge management. The paper discusses the actual technical achievements as well as in IT infrastructure utilisation and also in employment of virtual reality based systems. Special focus and deeper insight will be given to the fibre optics and WLAN hardware integration as well as software developments. The pocket personal computer (PC) is used to enhance underground material transport and data acquisition. The knowledge-based maintenance system (KBMS) integrates real-time virtual reality knowledge elements, such as repair process descriptions. It gives access to expert documentation by intelligent search algorithms and 3D representations of major mining machinery.

Jan 1, 2008

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Grigorescu, S Crimp, J H. Hodgkinson, P Kokic, W Jin

Mines are typically located in remote, inhospitable locations and movement of materials between site, processor and port are often at risk from extreme weather events. Mining companies have recorded multiple supply chain, production and logistics delays caused by climatic events. Recent analyses of extreme temperature and rainfall events (90th and 99th percentile values) for 1960 to 1985 and 1986 highlighted regionalised increases in the frequency and intensity of extremes. The trajectory of this change is likely to be maintained (IPCC, 2014) in regions where increases have occurred historically, suggesting that some parts of the industry may be faced with management challenges beyond current experience (Hodgkinson et al, 2010; Loechel, Hodgkinson and Moffat, 2012). Reliance on historical data to plan for extremes (such as scheduling production downtime to reduce impact) will become increasingly ineffective as the data become less representative of future conditions. Importantly, mine site remediation and closure management need to consider the future climate to ensure rehabilitation is sustainable under changing conditions.Vulnerability assessments and risk-reducing adaptation will become more common as the industry reaches to secure both a mine’s longevity and the industry’s reputation as shareholders and clients become less tolerant of repeated or prolonged interruptions (Hodgkinson, Hobday and Pinkard, 2014). Climate-resilient new mines may be planned using site planning tools combined with knowledge of future climate scenarios. Scenario tools are valuable for developing a gated risk management approach to reducing climate-risk during a mine’s life, through to the rehabilitation process and for managing care and maintenance or closed mines.CITATION:Hodgkinson, J H, Crimp, S, Jin, W, Kokic, P and Grigorescu, M, 2016. Life-of-mine planning tools for a changing climate – intuitive, interrogative, iterative, in Proceedings Life-of-Mine 2016 Conference, pp 71–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Y L. Ma, Y Yang, M Chen, W Bruckard

To improve the understanding of the reactions and mechanisms occurring during the leaching of sulfide ores at high temperatures a range of advanced characterisation and sensing tools have been combined to provide a sophisticated and powerful methodology to examine sulfide leaching systems. These include advanced electrochemical methods, surface chemistry and materials characterisation techniques such as synchrotron X-Ray Absorption Spectroscopy (XAS), X-Ray Photoelectron Spectroscopy (XPS), Scanning Electrochemical Microscopy (SECM), and in situ X-ray diffraction (XRD), together with new robust solid state chemical sensors for in situ real time monitoring of key aqueous chemical parameters. The methodology was employed to investigate various sulfide mineral leaching processes. For example, oxidation of arsenopyrite at elevated temperature involves complicated multiple reactions and the process is strongly influenced by the solution conditions, component speciation and mineralogy. The methodology was used to study this system both ex situ and in situ to gain a detailed understanding of the complex chemical reaction mechanisms operating. These mechanisms are discussed in terms of the observed leaching efficiency. The application of this methodology enables complex sulfide leaching systems to be understood more fully such that process efficiency can be improved.

Aug 24, 2022

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

By M J. Cole, J Zhou, D J. Borrow, S M. Iveson, K P. Galvin, J L. Sutherland

New technologies can easily take around ten years to commercialise. Strong research support is needed in parallel with the process of innovation and commercialisation, in building a deeper understanding of the underpinning physicochemical and hydrodynamic forces that deliver the separations, in achieving improvements, in the deployment of a new technology, and in expanding the innovation platform to create new IP. External investment beyond the research, derived from the genuine value proposition of transformational change, funds the pathway for traversing the so-called Valley of Death.

Aug 24, 2022

By C Antonio, R Narayan, A Scheuermann, S Quintero, M Edraki, M Ziemski

Tailings are mostly loose material and can be classed as non-plastic sandy silts. They also tend to have low permeability, resulting in slow consolidation (settling) rates and low shear strength, even after consolidation. These qualities make them prone to liquefaction and, therefore, physical instability. In contrast, coarse waste rocks possess high shear strength and permeability when stacked in dumps. However, air and water flow-through the voids can cause acid mine drainage (AMD) with significant undesirable environmental implications. Combining the two waste streams before disposal by mixing presents a potential opportunity to harness the desirable properties of both waste streams. This practice is termed co-mingling and is prevalent within the coal processing industry. Co-mingling of metalliferous mine tailings is, however, a relatively new concept. By combining the coarse waste rocks and fine-grained tailings streams, the fine tailings tend to fill the voids between the waste rocks, reducing hydraulic conductivity and advective air (oxygen) flow into the rocks, thus possibly reducing acid mine drainage (AMD). Conversely, tailings are introduced to large frictional particles from waste rocks, providing reinforcement, stability, and possibly improved drainage. New separation methods are being introduced to the mining sector, which have the capacity to extract waste with significantly larger particle sizes. High Voltage Pulse (HVP) is a technology in which relatively coarse particles ranging in size from 30 to 100 mm are exposed to an electric pulse discharge. This pulse preferentially fractures mineralised particles while leaving unmineralised rock (gangue) intact. The stream can then be passed via a screen, with smaller mineralised particles reporting to the undersize and removing coarser unbroken barren particles, thereby eliminating waste. Coarse particle flotation (CPF) is another emerging new technology in metalliferous mining that applies flotation separation to coarser particles than conventional flotation. These new technologies produce different tailings (waste) streams with varying physical characteristics and possibly surface chemistries. This research aims to test new tailings mixtures by applying the co-mingling concept to blend the reject streams generated by these two technologies (HVP and CPF) with the tailings produced by conventional flotation. Combining different waste streams before disposal can improve stability and potentially reduce the acid mine drainage (AMD) rate, thus enabling early access to the tailings storage facility for rehabilitation and closure.

Aug 2, 2023

By J Pearse, N Acosta, N McIntyre, M Angarita, L Camacho, C Huguet, D Arbelaez-Ruiz, J Ossa-Moreno, O Restrepo

Colombia is an example of a nation where mining makes a significant contribution to local and national economies. Due to the abundant resources present in the ground, there are good prospects for further development. However, the impacts of mining projects can include reduced access to good quality freshwater for other economic activities and/or biodiversity preservation (Ossa et al., 2018). As well as the water management challenges common to all mining regions globally, Colombia has particular challenges associated with its biophysical and socio-political traits. Land use change in many regions is dynamic including rapid development of agriculture and the development and abandonment of small scale mines. The value of ecosystem services provided by prospective mining regions also creates challenges in particular with regard to the páramos, the headwater wetlands from which about 70% of Colombia’s water supply has originated (Cleef 1981). Colombia also has particular challenges related to strong preconceptions about mining and its impacts on water. On the one hand, there is recognition that new large-scale mines are important for Colombia’s economy; on the other, there is deep distrust of the sector’s ability to operate with minimal adverse impacts (Gutiérrez-Gómez, 2017). Hence, any impact assessment is likely to face high levels of scepticism and scrutiny. Summarising the work of McIntyre et al. (2018), this abstract proposes a framework for assessing and communicating risks to regional water resources arising from the impacts of mines. The framework outputs aim to provide government and other stakeholder groups the scientific evidence needed to inform their viewpoints about mining development in the selected region, and a baseline from which to design a program of priority scientific research. CITATION:McIntyre, N, Angarita, M, Acosta, N, Camacho, L, Pearse, J, Huguet, C, Restrepo, O, Ossa-Moreno, J and Arbelaez-Ruiz, D, 2018. A framework for assessing and communicating water risks in prospective mining regions of Colombia, in Proceedings Life-of-Mine 2018, pp 49–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M W Kearns

The ERA - Ranger Mine ore processing operation consists of a sulphuric acid leach followed by counter current decantation and solvent extraction circuits. The most expensive unit processing operation at Ranger is the sulphuric acid leach. In 1992 and 1993 changes were made to the operation of the leach circuit. These changes have reduced power and reagent consumption in leach by 30 per cent and 20 per cent respectively with minimal effect on extraction efficiency. The first change was to operate the leach circuits at higher pHs than previously attempted. In addition a cap was placed on the amount of acid added to the leach circuit. Secondly, an on-line pH measurement system was installed and has reduced the variation with time of the leach circuit pHs. Finally, the number of leach vessels used was reduced from ten to seven. This action was undertaken after an examination of the uranium profile and the residence time in the leach circuit from previous years. This paper examines the above changes and assesses their effectiveness on plant performance and costs.

Jan 1, 1994

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D J Rawlings

The Palaeo- to Mesoproterozoic McArthur Basin contains a thick (-10 km) intracratonic platform cover sequence of unmetamorphosed and relatively undeformed sedimentary and volcanic rocks (Pietsch et al, 1991). It covers an area exceeding 180 000 km2 of the North Australian Craton (Figure 1), overlying segments of the older deformed basement and transitional igneous units. Volcanism in the basin (including transitional domain) followed a four-phase pattern. These phases are geologically distinct and widely distributed, and are also recognised beyond the McArthur Basin in many similar-aged tectonic provinces in northern Australia. The four phases are described briefly below. Regional and structural nomenclature used refers to Figure 1. A stratigraphic correlation diagram is presented in Figure 2.

Jan 1, 1994

By J M. Menacho, L Zhang, A Hoadley, L Verdugo, B Etschmann, W Bruckard

Since the introduction of Lithium-Ion Batteries (LIBs) in 1991, the market for lithium-ion cells has been driven by the high demand for portable electronic devices and more recently for batteries for the electric car industry. It is expected to grow rapidly to reach 2600 GWh globally by 2030 (US Government, Office of Energy Efficiency and Renewable Energy, 2021). However, there is a desperate need to recycle LIBs to recover valuable cathode materials and graphite. For this reason, several physical and chemical recycling technologies have been proposed to recover these materials from spent batteries. Amongst these, froth flotation technology is a potential cost-effective technology for separation of the graphite fraction from the lithium oxide components due to the natural hydrophobicity of graphite and density difference between graphite and cathode materials (Folayan et al, 2021).

Aug 24, 2022

By A Roudnev, P Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for both the end users and pump manufacturers. The traditional approach has been to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve froth pumping capability of mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance.CITATION:Loderer, P and Roudnev, A, 2018. A reliable solution for pumping mineral froth with challenging froth volume, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018