Search Documents

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

A substitute for rutile can be produced by leaching natural or pre-treated ilmenite in hydrochloric acid. Ilmenite in its natural form is an extraordinarily inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite so that it can be leached with dilute hydro- chloric acid (=2O% w/w) can be enhanced by pre-treatment steps of oxidation and re- duction. The temperatures at which oxidation and reduction are carried out have an effect on both the kinetics of these steps and the leaching kinetics and optimum temperatures for oxidation and reduction are 950 and 850¦C respectively. The mechanism of leaching of iron from pretreated ilmenite and the effects of rate of agitation, temperature, acid con- centration and addition of ferrous chloride to hydrochloric acid on leaching kinetics and production of fines are discussed in the paper.

Jan 1, 1984

A number of mines in Australia have experienced premature detonations caused by bulk explosives reacting with the rock type being blasted. Premature detonations are extremely high risk events as they are unplanned, occurring at any place, at any time, potentially resulting in high loss (personnel and equipment). Many Australian mines have also experienced spontaneous combustion where spilt explosive reacts vigorously with the rock type. Premature detonation in these cases does not occur due to the lack of confinement and the volume of explosive present, but these reactions could impinge on the surface initiation system and provide an early warning of future premature detonations. The explosive ground reactivity phenomena is not restricted to Australia with similar incidents being reported in North and South America, South Africa, China and South East Asia. All reported incidents have two common denominators, being the presence of sulphide rock types and nitrate based explosives. Both premature detonation and spontaneous combustion result from the same series of reactions of partially weathered sulphides that ultimately result in the violent decomposition of the ammonium nitrate based explosive. A number of relatively easily observable indicators can be used to assess a particular minesiteÆs potential for explosive ground reactivity. The presence of two or more of these indicators means that minesite personnel should contact their explosives manufacturer for assistance in determining if a problem exists and if so then developing strategies to overcome the situation. The paper describes the indicators as well as discussing, via a case study, the holistic approach required to efficiently develop a relevant æSafe and Efficient Blasting ProcedureÆ to deal with explosive ground reactivity problems.

Jan 1, 1999

By H Austrheim, A K. Engvik, A Putnis

How aqueous fluids move through rocks and minerals is a question of possible pathways and mechanisms. Existing pathways such as fractures and grain or mineral boundaries provide obvious channels for fluid movement. We show how minerals reactive in the presence of an interfacial fluid can be replaced by new product phases through a process of interface-coupled dissolution-reprecipitation. A resulting porosity in the new phase provides a new pathway for fluid movement and therefore mass transport through the mineral, which progressively reacts at a moving interface. Eventually fluids of new and changing composition can pass through originally solid minerals and move on further, taking remobilised elements with them, to be reprecipitated whenever the chemical and/or physical conditions allow. One such example is albitisation of rocks associated with mineralisation.

Jan 1, 2008

By Voermans F. M, Hoyle M. W H

The Archean geological sequence in the West Pilbara region (Fig 1), a deformed greenstone volcano-sedimentary succession regionally intruded by layered mafic/ultramafic lopoliths, batholithic granites, granite stocks and transected by swarms of dolerite dykes, has prompted several companies to search for a variety of base metals and and platinoids (Fig 2). In the first instance, detailed aeromagnetic surveying was completed, producing patterns of marked magnetic anomalism which proved substantially successful in the demarcation of areas warranting geological reconnaissance and detailed follow-up. Revelant to this paper were the obvious magnetic features overlying outcropping and buried mafic/ultramafic bodies which ultimately were proven to be host to Ni-Cu sulphides, pgm, Ti, V, Cr and, more recently, Ag and Au mineralisation. Routine stream sediment, soil sampling and ground geophysical techniques of the day appear, in most cases, to have been adequate in the detection of mineralisation, except in the case of Radio Hill massive sulphides where the Turam E.M. (1972) signal essentially failed to detect the blind conductor (Peters, de Angelis 1987).

Jan 1, 1988

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

By R Puglisi, G McPhail, B D. Jilbert

The increased international focus on sustainable development and cost improvement, coupled with the unpredictability and adverse impact of droughts in Australia and globally, has highlighted the critical need for responsible management of water within the minerals industry. The Rio Tinto Technology Group recently initiated a priority program to examine how water management practices could be improved within the GroupÆs spheres of activity. Rio Tinto Technical Services (TS), the technical services consulting group of the Technology Group, has for many years been undertaking water management reviews and assisting group operations with the development of responsible water management strategies and plans. Rio Tinto therefore requested that Rio Tinto Technical Services develop a world-class approach to mine water management that will drive improvement in strategic assurance and operational efficiency of water at the companyÆs managed operations across the world. The initiative, known as æExcellence in Water ManagementÆ, includes the selection and use of state-of-the-art management, technical tools and methodologies to strive for best practice. The Rio Tinto Technical Services approach facilitates a consistent and objective assessment of performance across the entire spectrum of complex water management issues within a mining operation, from initial exploration through to decommissioning and close-out of the operation. Based on this rigorous assessment, detailed action plans can be developed, prioritised and scheduled for subsequent implementation. This paper presents the progress and experience gained to date in the æExcellence in Water ManagementÆ program, demonstrated by means of a pilot study conducted at Northparkes Mines in New South Wales.

Jan 1, 2003

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By Bilodeau M. L

The paper describes a model which has been developed to assess the economic charac- teristics of base metal investment in Canada and the effects of past, present and possible future sharing systems, particularly mining taxation systems, thereon. The model is illustrated by applying the 1976 Canadian tax system to the economic characteristics of base metal discoveries made in Canada during the 1951-1974 period.

Jan 1, 1977

Mineral resource classification is essential because it is required for public disclosure. The resources must be binned by a qualified person into measured, indicated and inferred categories using an appropriate methodology. The classification methodologies used have long been a topic of research and discussion. There are various traditional and geostatistical methods used in practice. Some are more popular than others. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for mineral resource classification. Therefore, some experts have adapted the methodologies tailored for the deposits they are working on, but many simply use the methods they and their clients understand and are comfortable with. In this paper, a new approach is presented to classify the mineral resources using a data geometry index. This index combines both traditional and geostatistical aspects of resource classification based on the data configuration around the block interpolated. It is a function of several variables such as kriging variance calculated for a block, distance from the block to the nearest sample and the average distance of all samples used to interpolate the block. Thus the approach using this index takes into account the spatial data configuration around the block being estimated, as well as the traditional distance criteria. The data geometry index and how it is calculated is explained. A case study for a gold deposit is presented to see how the classification based on this index compares to the existing methodology used in this deposit for mineral resource classification.

Sep 26, 2011

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

In recent years the use of directional drilling has become increasingly popular in several applications. These include shaft pilot holes, exploration drilling, mine service holes and drilling beneath surface structures and obstacles. The prime objectives are to increase accuracy and reduce time, cost and environmental disturbance.

Jan 1, 1992

By Gemuts I, Hudson D. R

Massive sulphide mineralisation at the Miriam prospect, near Coolgardie, Western Australia, is fracture-controlled and associated with disseminated sulphides near the basal contact of an ultramafic lens. The lens is peridotitic in composition with a pyroxenitic zone at its base, and lies within a sequence of altered high-Mg basalts and pillowed tholeiitic basalts. Recrystallisation of the ultramafic rock has resulted in the development of secondary olivine. The average composition of the sulphide fraction of massive ore is Cu = 4.4%, Co = 0.3%, Ni = 23.0%, Fe = 31.8%, S = 40.6%, consisting of the supergene assemblage violarite-pyrite to a depth of 210 m.

Jan 1, 1973

By Hart A. T, Lanigan P. G

BHP is currently undertaking research into plasma are metallurgical processing at the Central Research Laboratories (CRL), Shortland. The use of high intensity plasma arcs for melting and smelting has a number of advantages, including; the ability to control atmosphere and furnace operating conditions, total enclosure, high temperatures, versatility, and low in-process inventory in a compact system. The intensive conditions, achievable in a plasma furnace system, make it particularly useful for the smelting and melting of difficult-to-treat materials, such as ore and metallic fines and refractory ores. Two transferred arc plasma smelting furnaces have been set up at CRL; a 100kg furnace is used for small scale melting and smelting studies and a 1 tonne furnace for pilot scale plasma processing studies and equipment development. Power is supplied by a 1MW GEC thyristor DC power supply. A 220kW DC power supply is available for "off site" pilot process trials and demonstrations, and a 150kW non-transfered are plasma torch is also available for other studies. The facility has been designed to allow maximum flexibility in researching and developing applications in metallurgical processing and transferring developed technology to company operations. The objectives behind the development of the facility, details of the facility and an outline of current research areas will be Discussed.

Jan 1, 1987

The geologic settings, geochemistry of host rocks, mineralogy and metal values in modern back-arc volcanic-hosted massive sulphide (VHMS) mineralisation are very similar to those in many ancient polymetallic VHMS deposits. The geology, distribution and styles of seafloor mineralisation in modem back-arc basins, especially the eastern Manus and Lau Basins, southwest Pacific, are compared to VHMS deposits in the Mount Read and Mount Windsor districts of Australia . Based on exploration and research in modem back-arc settings, geologists are now observing the direct analogues of the polymetallic VHMS deposits currently being exploited in ancient back-arc volcanic belts throughout Australia and the world.

Jan 1, 1995

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978