Search Documents

By E E. Hall, C D. Taylor, D S. Yantek

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

Jan 1, 2005

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By Johnson RD

The variation in coal properties and the coal seam reduced level can be analysed using partial trend-surface analysis techniques. For the area studied seam reduced level and seam thickness data from the Bulli Coal yield trend-surfaces with a high coefficient of determination, since they have relatively small systematic local and random components in their overall variation. Sulphur content appears to have no significant re.gi_onal trend, and phosphorus content has a very weak regional trend. Other analytical variables have regional trends which are of intermediate strength. The strike-directions of.the statistically significant first degree! trend-surface are similar, sug-gesting.: that the variation of the several coal properties was controlled by a set of- related causes. The relations apparent from the dip and strike of the first degree trend-surfaces are similar to- those which are apparent from the trend- surface residuals and'from the results' of canonical trend-surface analysis.'.. It is probable that differential subsidence controlled the areal

Jan 1, 1975

By Thomas W

Due to record low tin prices and an uncompetitive position in world markets, the Renison tin mine has undergone three major phases of restructuring in the last three years. This has involved substantial job losses, almost all of which have been through voluntary retrenchments. Retrenchments took place in 1988, 1990 and 1991.The last phase of restructuring was the most dramatic, as many aspects of the operation of the mine were changed. New pay structures were introduced, and the miners' contract system was scrapped. Drastic pay cuts occurred in many areas, although the opportunity was also taken to increase pay at some of the lower levels where inequities existed. Work practices were changed, as was the management structure.

Jan 1, 1992

Historically BHP Billiton Alliance Coal Operations Pty Ltd (BMA) have generated resource models from widely spaced data points (drill holes). The accuracy of these models has been influenced by the degree of local structural disturbance of the coal seams and by the choice of interpolators used in the modelling process. In some circumstances unacceptable vertical errors of up to 10 m have been observed whilst mining. New terrestrial photogrammetry or laser imaging technology now allow the 150 or so kilometres of exposed highwalls in BMA to be rapidly, accurately and safely mapped and the three-dimensional images economically incorporated into resource models, reconciliation grade control models, drill and blast designs and for pit stability analysis.

Jan 1, 2005

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By A S. M A Haseeb

Zircon is the second in abundance among the heavy minerals occurring in the beach sand along the coastal belt of Bangladesh. In this study a detailed characterisation of Bangladesh zircon extracted at the pilot plant of the Bangladesh Atomic Energy Commission at CoxÆs Bazar has been attempted using chemical analysis, X-ray diffraction and optical microscopy. From the chemical analysis it is found that Bangladesh zircon has a purity of 95.88 per cent. The main impurity in Bangladesh zircon is titanium oxide (3.01 per cent). This is followed by iron oxide (0.42 per cent). A number of other oxides are also found. Microscopic study revealed that Bangladesh zircon has an elongated, prismatic shape with pyramidal termination in about half of the grains while the rest are more or less rounded. Some fractured and irregular grains are also found. Bulk sample of Bangladesh zircon in the as-received condition shows a yellowish brown color. However, individual zircon grains are seen to be almost colourless and transparent under polarised light. XRD study confirmed good crystallinity in the sample. Under the microscope it is found that zircon grains constitute 94 per cent while total impurities amount to six per cent in Bangladesh zircon. This result agrees fairly well with the chemical analysis results. Microscopic study identifies oxides of titanium (both rutile and ilmenite) to be the main impurity, in conformity with the findings of chemical analysis. Further, monazite was also identified as an impurity under the microscope. An iron bearing coating is also found on a few zircon grains. Most of the impurities found in Bangladesh zircon exist as discrete minerals.

Jan 1, 2000

The ownership, policies, organisation, structure, market, financial considerations and communications of a large resource project vary significantly through its discovery, feasibility, development and production phases. The extent of these changes, from discovery in 1957 through to 1979, is examined for the Mt. Newman iron ore project in the Pilbara region of Western Australia and some of the factors that influenced it are detailed. This shows that only some of the influences are under the control of the mine owner/operator, despite their significant impact on the returns for the massive capital invested. The effect of the general business climate on the various phases is also examined.

Jan 1, 1980

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By Yamamoto Y, Ohyama H

In case of NATM, mechanical cutting is desirable in view of the original purpose of not spoiling natural ground. As typical tunnelling machines, there are two (2) kinds available: one is "Full Face Excavator" known as TBM (tunnel boring machine), and the other is "Roadheader" known as Part Face Excavator. By the use of the former, accurate profile cut is made possible, but there is a limit in the shape of a cutting section. By the use of the latter, cutting of various sections is made possible, but in order to cut a section economically and accurately, operators are required to have a high level of skill. In this text, we introduce Automatic Controlled Profile Cutting System (hereafter "ACPC" System) developed as a roadheader.

Jan 1, 1987

By Maxwell HW

Pacific Coal Pty Limited (a wholly owned subsidiary of CRA Limited) managed the interests of six members of a joint venture formed to mine and export eight million tonnes of export quality steaming coal from a mine developed at Blair Athol in the Bowen Basin of the Central Queensland coal fields. The mine is now operated by Blair Athol Coal Pty Ltd. Crooks Michell Peacock Stewart Pty Limited (CMPS) was awarded a project management and engineering contract for the total mine portion. Following a feasibility study, CMPS carried out an Optimisation Study which produced changes to the design of the project, thus resulting in the project budget being reduced by some A$13 million. In spite of a number of late additions to the scope of work, the project was completed at a final cost of A$148 million, many millions below the reduced project budget. The project was also completed several months ahead of schedule. Total services were provided to take the project from feasibility stage through to the establishment of an operational facility and included project management, planning and control, accounting and financial control, as well as the organisation of engineering, procurement, construction, industrial plant commissioning, and technical training matters.

Jan 1, 1986

By P C. Hagan

Production scheduling is often reliant on an estimation of a mineÆs trucking capacity. While this mechanistic approach is relatively simple, it often over-estimates actual throughput resulting in under-utilisation of downstream process and a shortfall in revenue. An alternate approach has been developed that recognises the interdependency between processes in the mine production system including materials loading, haulage and crushing. This approach incorporates a heuristic model based on queuing theory that accounts for the variability in performance of individual processes and that this paper presents the results of a study comparing the conventional approach to mine scheduling with a capacity constrained model at a large open cut mine having a truck and shovel fleet. The capacity constrained model consistently predicted a lower material throughput compared to the conventional approach. Differences in throughput between the two approaches were found to increase with loading time, for example when loading time exceeded 3.9 minutes there was a shortfall of up to 40 per cent in estimated throughput. Longer travel times tended to ameliorate any differences. When applied to a mine schedule that extended over a two and a half year period, the difference was equivalent to a shortfall of nearly eight per cent in total material movement.

Jan 1, 2007

By M P. Sandy

Some Western Australian underground mines are challenged by very high stress gradients. This environment frequently results in poor induced ground conditions and damaging seismic activity. In some cases, rockbursting or squeezing ground has been observed as shallow as 250 m below surface. Very few mines operating at depths greater than 500 m experience no stress-related issues. As a general result of this difficult environment, there are a growing number of mines that are now challenged or have been closed by induced geotechnical problems. Often, the up-front savings or perceived advantage of an inappropriate mine plan may be entirely lost to the real cost of managing the hazards, or a write-down of reserves resulting from access difficulties will diminish the economic position of the mine. From an engineering perspective, it is best if stress-related hazards can be proactively minimised, because reactive measures offer less improvement in risk exposure. In this paper, some examples of sequencing techniques for managing difficult environments are contrasted with examples from mines where developing hazards have adversely affected production or the economic viability of the project.

Jan 1, 2003

By P Grouhel

In the recent years several new blasting technologies have come into use in surface mines. Electronic initiation, low-density emulsion explosives and modelling software are in regular use throughout the world. In Australia, these new technologies have achieved significant application, largely in open cut coal mines where more than 20 per cent of blasting is now conducted with electronic initiation systems. These new techniques have contributed to the vast improvement in blasting outcomes evidenced by increased recovery of saleable product and faster excavation rates. In large surface mines, OricaÆs unique combination of electronic initiation systems, bulk emulsion explosives and modelling software can be harnessed to target critical value outcomes. This includes targeting better fragmentation, increased ore uncovery rates and better wall stability û all adding to improved mining operation profitability. Orica Mining Services have combined these technologies into a set of offerings called Blast Based Services (BBSÖ). The paper describes applications of these new technologies and possible benefits in large surface mines.

Jan 1, 2007

By Armstrong ME

The gas bubble energy generated by an explosive plays a major part. in the fragmentation, muckpile movement and damage produced. Previously, the interaction between gas pressure and the rock has been interpreted from a theoretical basis or a qualitative study of breakage mechanisms. A method to measure the fluctuations in gas pressure in rock adjacent to the blast has been developed. This peak pressure will vary with structure, as well as with distance and explosive type. The technique is simple to apply and can be used to observe the flow rate of gas at. varying distances. The apparent velocity of penetration is an indication of whether gas has travelled through pre-existing or blast induced cracks. The technique provides a ?n:eans of determining the suitability of an explosive for a given rock type, depending on the amount of displacement desired. The technique has application in optimir.irig throw blasting and predicting and controlling damage, particularly in highly structured rock masses.

Jan 1, 1986

By Moxon NT, Torrace AC

The detonation pressure of an explosive is a function of its density and its velocity of detonation (VOD) and relates directly to the degree and manner in which the explosive loads the surrounding rock. The suitabil- ity of an explosive to any particular situation is determined not so much by the total energy released but more by the rate at which it is released. As the science of rock blasting advances it is becoming economically more important to quantify explosive performance, particularly with respect to quality control and fragmentation. As part of a major explosive user, BHP Central Research Laboratories have developed a number of tech- niques to determine the detonation characteristics of explosives. These include a method of continuous velocity of detonation measurement based on the SLIFER principle. This not only enables the VOD of the explo- sive to be determined, but also has the versatility to allow factors such as under priming, slow run up, the effect of water, variable energy load- ing and the velocity of the shock wave in the stemming to be assessed. Multi point VOD systems have also been developed for more routine appli- cations. With a minor modification they can be used to determine the absolute delay of detonators accurately and economically. Direct deto- nation pressure measurement methods have also been developed based on piezoresistive techniques. Future developments include the incorpo- ration of all the above techniques into a single, portable package, allow- ing easy use on the mine site.

Jan 1, 1988

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

By Mirabediny H, Whitchurch K

A computerised simulation model has been developed to select the most suitable digging method of a dragline operation for a given geological condition. The developed procedure uses a geological ore body model as the basis for the geologic database. The simulation selects the most cost effective dragline digging method from a database of various dragline digging methods The database consists of common and innovative dragline methods currently used in Australian open cut mines. A generalised computer package, DSLX, was extensively used to simulate various dragline digging methods. The DSLX software uses predefined functions to build strip geometry, working benches, blast profiles and spoil piles. The outputs from DSLX in form of volumetric, swing angles and hoist distances data are then aggregated with dragline specifications and site time study data to compare productivity of selected digging methods. The result of a case study showed that this procedure lends itself to the 'optimum' selection a dragline digging method for a given coal deposit.

Jan 1, 1995

By Rajan S, Mainwaring P, Gould WD, Beaulne M

Polished discs of a complex sulphide ore were leached with three lixiviants; a mixed culture of Thiobacillus ferrooxidans and Thiobacillus thiooxidans, Thiobacillus ferrooxidanalone, and ferric sulphate. At either one or two week intervals the discs were examined by scanning electron microscopy, and the amount of soluble metals released from the discs were determined. The mixed culture solubilized more Cu, Zn and Pb than did either ferric sulphate or T. ferrooxidans alone. However, no differ-ences were observed between the three treat-ments by scanning electron microscopy during the first 44 weeks. The minerals were attacked in the following order: pyrrhotite, cubanite, sphalerite, pyrite and chalcopyrite.

Jan 1, 1990

By N Harries

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The æslope stability radarÆ (SSR) has been developed to better manage those risks. The SSR can remotely scan a rock slope to continuously measure any movement of the face. The system can detect and alert users of wall movements with submillimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, Africa, Chile and the United States. Greater than 100 rock falls and waste dump failures (from several tonnes to millions of tonnes) have been monitored, and on every occasion precursor æwarningÆ movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper presents recent case studies of how the SSR technology has provided safety and productivity benefits to large open cut metalliferous mines.

Jan 1, 2007