Search Documents

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By Z Lubosik, S Prusek, M Plonka, B Syrek

"The most commonly used method of thick coal seam extraction in Polish deep mines is multislice longwall (MSL). In MSL stability of goaf in the roof as a result of previous extraction in upper slice is a major geotechnical consideration that must be managed.This paper outlines the results of a wide range of investigations carried out in three longwalls that were in operation in a multislice system using caving with additional fly ash goaf stowing. The longwalls were operated by Katowicki Holding Weglowy SA (KHWSA) in the Upper Silesian Coal Basin of Poland.Examinations were completed on the properties of goaf at the roof of longwalls ie measurements of strength parameters of the goaf material by means of a borehole hydraulic penetrometer, determination of the goaf condition by means of a borehole endoscope and laboratory testing of the caved rock. The results of underground examinations of the loading on yielding arches in the gate roads associated with these longwalls and measurements of vertical and horizontal convergence are also presented.CITATION:Prusek, S, Lubosik, Z, Plonka, M and Syrek, B, 2014. Multislice longwalling for thick seam extraction – properties of goaf in the roof and gate roads behaviour, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By S M. Arndt, D Tyler, F Reusch

Although significant advances have been made in understanding the mechanics of pit slopes, numerical modelling hasnÆt significantly impacted on the reliability of the design process. It is well known that legacy modelling approaches donÆt simulate large slopes well. In recent times, the emergence of very large finite element (FE) models with more than ten million degrees of freedom and the ability to simulate a large number of discrete structures, has allowed a step change in the simulation precision for slopes. The model size allows global and local effects to be realistically simulated in one model for the first time and the process can be better integrated into normal open pit slope engineering processes. Some examples of simulation of very large open pits are shown that demonstrate the challenges and some recent advances in modelling large slope behaviour. Significant limitations in the current measurement and observation regimes of open pits have been identified.

Jan 1, 2007

By J Bartlett, P Quigley

Historical research has played a significant role in the rebirth of the Bendigo Goldfield. The historical research undertaken by the company has been directed to specific areas such as verifying the total gold production of the field, the gold production from defined blocks on each of the major anticlines, the extent of workings of each mine which exceeded 200 m depth, the size and style of reefs mined in each shaft and also within specific domains of the field. Application of this data has assisted in the determination of possible dimensions of different reef styles and the location of mineralisation within each reef system. Description of grade variation, percentage of quartz and the amount and species of accessory sulphide minerals, as well as early geotechnical observations accompanying stoping methodologies, provides valuable analogues for reef structure being defined in the current program. Historical information on shafts on the two anticlines the company is exploring has allowed the postulation and recognition of repetition of reef development within the same stratigraphy in the hinge zones of the adjacent folds. The similarities of mineralisation styles across the field within both specific lithological units and structural setting has had important implications in respect to exploration drill targeting and the estimation of grade and tonnes.

Jan 1, 2003

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

A methodology for the fatigue life estimation of load haul dumpers, employed in underground platinum mines, has been developed and applied. This method entails the quantification of operating conditions by means of stress measurements. The measurements are then translated into a fatigue loading factor for a finite element model. The results of this analysis are then used to compare all the critical connections in the structure to detail categories in relevant fatigue codes, and predict a life in operating hours for the vehicle structure. The method was applied on a specific model and the results of this analysis were compared to actual failure occurrences with reasonable accuracy. It is intended that the methodology be embedded into performance specifications and purchasing contracts and that technology transfer to OEMs be achieved. Based on the experience of this project and other similar exercises it is estimated that structural life expectancies may be increased across a typical fleet of trackless mining vehicles (LHDs, drill rigs, utility vehicles, dump trucks) by at least 20 per cent.

Jan 1, 2005

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By M R. Davidson, M P. Schwarz

A model for column bioleaching is investigated to identify and understand aspects of bacteria in bioleaching applications, which have implications in heap bioleaching operations. The model is used to simulate scenarios that would otherwise be time consuming to perform experimentally. This study uses a model of bacterial transport and attachment/detachment to ore particles, with a bioleaching model for the depletion of a copper-sulfide, also accounting for liquid and gas flow and gas/liquid oxygen mass transfer. The model includes aspects such as oxygen and ferrous ion consumption, coupled with leaching of a copper-sulfide via the shrinking core model. The model is used to investigate how the rate of leaching is affected by the bacterial concentration in the columns, by the bacterial regeneration of the leaching oxidant ferric ions. The model is also used to assess the impact of oxygen limitation and inoculation method on the copper leaching. Some comparison of the model with experimental data will be shown.

Jan 1, 2004

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

By E Jak, M Shevchenko, D Shishin

One of the key aspects to develop sustainable metallurgical production is to ensure that the predictive power of thermodynamic tools is brought up to a new level of accuracy and reliability. Exploring new polymetallic processes, integrating primary and recycled materials, means utilising the uncharted areas within the Cu-Pb-Zn-Fe-Ca-Al-Mg-Si-O (major) – Cr-Na (slagging) – As-Sn-Sb- Bi-Ag-Au-Ni-Co (minor) slag-solids-metal-matte-speiss-sulfate system. This requires extensive integrated experimental and thermodynamic modelling study, which is underway at PyroSearch at the University of Queensland (UQ).

Aug 21, 2024

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

A mathematical model for spontaneous combustion of coal with moisture included is presented in this paper. The one-dimensional unsteady state model consists of conservation equations for oxygen, water vapour and inherent moisture of coal and energy for both gaseous and solid phases. A first order Arrhenius reaction rate for oxidation under both pore diffusion and chemically controlled reaction regime is considered. The rate of evaporation or condensation is also considered as a function of temperature of coal, water content of coal and gas streams. The equation of the model is solved numerically by the finite difference technique. Influences of different parameters on the process of spontaneous combustion can be examined by using this model. Also the model can be used to simulate full-scale storage conditions.

Jan 1, 2005

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R Benton

Since commencement of underground production in March 2006 the Kencana K1 orebody has delivered over 0.9 Mt of ore containing 1.18 Moz Au until April 2009. The Kencana deposits are part of the Gosowong goldfield located on the island of Halmahera in eastern Indonesia. The district has produced over 2.3 Moz since mining commenced in 1999 with the first two deposits extracted by open pit methods. The K1 deposit is technically challenging being a vein style deposit with poor to very poor ground conditions and a relatively low overall dip of around 45 degrees to mine grid east. It is mined under geological control by underhand cut and fill methods utilising cemented paste backfill aiming for 100 per cent extraction. With these conditions the operation was mine limited in the initial two years of production resulting in low stockpile levels for mill feed blending and hand-to-mouth mine to mill production. Mill feed rates have increased from 30 t/h to 55 t/h over this period following business improvement projects while mine production has escalated to match this increase as deeper levels of the deposit are accessed. The operation has now become mill limited. Monthly mill gold production from Kencana has ranged up to 50 000 oz with head grades ranging between 8 g/t and 122 g/t Au on a daily basis. As individual grade control assays can extend into the per cent Au range there are challenges in sampling, modelling, mining, blending and milling the Kencana orebody. At the time of commencement of ore driving in K1 the national geology team had little prior experience in underground mining and systems were in early development. The variances in feed grade and tonnages have been reduced with time as the operation evolves and business improvement initiatives are undertaken to smooth peaks and troughs in ore supply. Two such initiatives in the geology department have added over US$20 M of additional revenue per annum.

Jan 1, 2009