Search Documents

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By H Utama, R Heryadi

The demand for environmentally friendly commercial explosives has increased globally due to concerns regarding environmentally friendly mining activities. Ammonium nitrate fuel oil (ANFO) and bulk emulsion explosives (BEE) are two kinds of civil explosives primarily used in coal and mineral mining in Indonesia. Indonesia is one of the leading countries in coal and mineral mining production and export, with abundant resources; therefore, the consumption of civil explosives such as ANFO and BEE is enormous. The selection and evaluation of commercial explosives are mostly done on the commercial and technical side, and no assessment is made based on environmental aspects. This preliminary study evaluates the economic value and environmental burden of greenhouse gas emissions produced by ANFO and BEE and determines which type of explosives is more environmentally friendly. The combination of environmental and economic indicators, eco-efficiency (E/E), was selected to investigate BEE’s economic and environmental performance compared to ANFO. The life cycle of greenhouse gas emissions of BEE and AN was determined using previously available studies and simple calculations. The cost of the product or explosives was used to represent the economic value. The E/E results showed that environmental and economic sustainability could be enhanced using BEE.

Sep 1, 2024

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

By D François-Bongarçon

The link between geostatistics and Theory of Sampling (TOS) is examined again in view of new findings made while trying to compare predicted sampling variances and estimated grades (using geostatistics) on the same material, and this provides an important consistency requirement whenever calculations are made that involve both theories in a comparative way. It also briefly explores the relationship to De Wijs fractal model of mineralisation and eventually provides new support for the use of consistency theory for calibrating TOS variance formulas.CITATION:François-Bongarçon, D, 2017. Theory of Sampling and geostatistics – the ultimate link, in Proceedings Eighth World Conference on Sampling and Blending , pp 391–394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By N LaBranche, G Callinan

There has been a reduction in overall workforce in the mining industry during the current downturn; a corresponding reduction in fatalities and high potential incidents (HPIs) has not been observed. The same contributing factors can be seen in the vast majority of these incidents. These include inadequate supervision and lack of adequate risk assessment. How management structures, trains and leads an operation can have a great impact on eliminating these factors and reducing the risk of fatalities and HPIs.Contractors now account for 41 per cent of full-time equivalent employees in the Queensland mining workforce, and are disproportionately represented in the majority of fatalities and HPIs. Having a clear strategy for how contractors are integrated into the workforce is crucial. This talk will include a discussion of the data as collected in the Department of Mines and Natural Resources department database, and offer solutions based on this data.CITATION:LaBranche, N and Callinan, G, 2016. Organisational factors in fatalities and high potential incidents, in Proceedings International Mine Management Conference, pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By L Dawson, S Carr-Cornish, N Boughen, K Moffat, S Masterson

The risk and consequences of community rejection and loss of a social licence to operate is well articulated (Moffat et al 2018), however, the means for systematically managing this risk are less established. At the local scale, a mining operation is said to have a social licence to operate (SLO) when it achieves ongoing acceptance or approval from the local community and other stakeholders who can affect its profitability (Graafland, 2002). Without this social acceptance, it is very difficult for a business to operate effectively or profitably. It is well understood that social (or community) acceptance of a mine and its associated operations is a reflection of the quality of the relationship a company has with their host community (Thomson & Boutilier, 2011; Lacey & Lamont, 2014; Parsons et al., 2014; Moffat et al., 2015). Community relations are an integral part of successful mining operations and where these interactions are effective, they tend to foster mutual understanding, trust and support between a company and the host community (Kemp et al., 2006; Holley & Mitcham, 2016). Research further demonstrates that where such interactions are perceived to be procedurally fair, the increased trust created in these company-community interactions tends to lead to higher levels of acceptance of mining operations (Moffat & Zhang, 2014; Lacey et al., 2017).The challenge, however, is how to listen systematically to communities that mining and associated operations; communities that are often located across vast geographic areas and with diverse demographics. To date, traditional methods deployed to both guide and evaluate community engagement and social investment activities have been challenged to reflect the nature of the phenomenon they seek to observe, the voice of community. For example, detailed baseline surveys of community attitudes every three years by companies, as is the requirement within the policy frameworks of most large miners, provide rich insights but do not reflect the dynamic, temporal nature of the relationships that underpins their SLO. These processes typically are largely opaque to communities and distinct from the company’s engagement activities. The CSIRO Local Voices project was developed with Rio Tinto to go some way towards meeting this challenge of how to listen to the voice of community systematically. CITATION:Moffat, K, Dawson, L, Carr-Cornish, S, Boughen, N and Masterson, S, 2018. Listening to Local Voices – a systematic approach for understanding what a social licence to operate means for Rio Tinto in the Pilbara, in Proceedings Life-of-Mine 2018, pp 8–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J A. M Luz, A T. Bernardes

HukkiÆs law is an empirical law, which does not take into account several events of energy loss during the fragmentation processes. Since experimental results are very difficult to obtain, for a large range of fragment sizes, the verification of the law is very difficult. The relation between fractures and fragmentation processes with fractal geometry was proposed some decades ago. Empirical laws known in this context show basic features of fractal geometry, mainly self-affinity and power law behaviour. Thus, in this work a model was developed to simulate the fragmentation process and to check the relation between energy consumption and fragment sizes. The model is represented on a regular lattice. Links can represent pathways for fracture processes. The events of fragmentation have energy given by a probability distribution function. In the model there is no mass loss. Propagation of fractures occurs as self-avoiding random walks on the regular lattice.

Sep 26, 2011

By J Rutter, S Dunham

Technological advances in sensor and material handling technology has enabled a step change in mine operations performance. Sensors capable of monitoring the grade of broken rock mass can be mounted on shovels, truck loading units or conveyors allowing highly precise ore/waste decisions to be made on small parcels of rock, increasing selectivity. This increased selectivity has the potential to remove sub-economic material from the product stream prior to incurring ore treatment costs. Bulk ore sorting is capable of intervening at <10t “pods” on Run Of Mine conveyors, or alternatively at per bucket loading (5-100t) or truck scale (30-350t) parcels of ore. This Grade Engineering technique being developed by CRCORE (Rutter, 2017) can improve mill feed grade, remove deleterious materials and ensure that the high capital intensity ore treatment facility is presented with the best ore feed strategy. While this technology can improve mine economics, estimating the performance of a bulk ore sorting system is challenging. Traditional resource estimation practices such as Ordinary Kriging and Inverse distance weighting (IDW) are based on weighted averages, a process that smooths the grade profile, reducing modelled variance and dispersion. Its purpose is to generate a globally unbiased result but is less suited to generating a model of adequate granularity to enable confidence in local grade heterogeneity. This is an essential component for bulk ore sorting success. Estimating ore sorting performance requires knowledge of the grade-tonnage curve at the scale of the sensor diversion unit (SDU). Evaluation based on an estimator that smooths the SDU distribution will not correctly predict ore/waste separation or economic performance. Alternatives to traditional linear geostatistics have been tested on a variety of mineralisation styles. Additionally, a number of heterogeneity metrics have been developed to assist with evaluation and assessment. The difference between estimation for grade (metal) and modelling for traditional mining block models, versus methods used for predicting heterogeneity and variability are explored.

Nov 10, 2020

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

By M J. Pejovic, I Miljanovic, A Milutinovic4, T Benovic, A Petrovski

The paper presents a model of a multigrade monitoring-management structure for support to decision making and management in real and extended time in mineral processing (MP). The model was created as a result of a long-lasting research, design and development of mining, computer integrated monitoring-management systems. Apart from the general explanations, the authorsÆ state in the introduction that efficiency of a system for support to decision-making and management in mineral processing is more difficult to achieve by conventional approaches, than by the fuzzy logic approach. Starting from the multiphase structure of process flows in MP, the following are process and monitoring-management oriented graphs. The graphs served as a foundation of the multigrade hierarchical fuzzy model for support to decision making and management in MP. Following the example of the monitoring-management system of the æRudnikÆ mine flotation plant, fuzzy logic implementation was shown. The key conclusions of the paper are that fuzzyfication of layers of the decision making and management model has full justification due to the complexity and dynamics of mineral processing processes, complications and often insurmountable difficulties concerning the precise description of real systems by conventional mathematical tools, variability of external influences, and the (general) non-linearity of the MP processes management criteria functions.

Sep 26, 2011

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By S K. Ray

Open fire in a mine gallery causes large-scale damage to property and sometimes precious lives. Such fires produce two distinct effects, the throttle effect and the buoyancy effect. These effects disturb the ventilation system of the mine. To understand the complex dynamic phenomenon of open fire and its effect on ventilation systems, a mine fire model gallery has been designed and constructed at Central Mining Research Institute, Dhanbad. Two sets of experiments at air velocities of 1 and 1.5 m/s were conducted in the gallery using coal samples from the Dobrana seam of the Raniganj coalfields. After about an hour of development of fully-fledged fire, heavy backlash, with smoke and fumes, was observed. At the time of backlash occurring the gallery was divided into two zones. In the region of the gallery from the base up to 1.4 m the airflow was normal, in the remaining upper portion the airflow was the reverse. Air quantity reduced substantially, while pressure dropped across the fire zone, the products of combustion (POC) and temperature increased during the period of the throttle effect. It has been revealed from these studies that with an increase in airflow, pressure drops across the fire zone, POC, temperature and reduction in airflow increases. This paper addresses the important design features of the gallery, the instrumentation system, the experimental procedure and assesses the effect of open fires on mine ventilation systems.

Jan 1, 2005

The tangible effects of leakage are presented graphically, and a technique for quantifying the leakage characteristics of a ventilation column using the æSolveÆ capabilities of a common spreadsheet is demonstrated. A case study of a working decline in Western Australia is used to demonstrate the potential for more realistic design of development ventilating systems, and for more cost effective management of the condition of the duct.

Jan 1, 2002

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Lainé, M Badawi, A C. de Araujo, Y Foucaud, C Veloso

Flotation is the one of the most used techniques for the mineral separation of non-ferrous ores worldwide. However, the increase of the complexness along with the decrease of ores liberation sizes ought to become important challenges for mineral processing, including flotation. It now appears necessary to better understand the fundamentals of the flotation process, particularly the adsorption of flotation reagents at the liquid/mineral interfaces, to propose further improvements. Flotation relies on different phenomena: surfactants adsorption, on one hand, and collision, adhesion, and transport of particles with bubbles, on the other hand. For acknowledging the reagents adsorption mechanisms, molecular modelling tools borrowed from chemical and material sciences, are increasingly used. Atomistic simulations were successfully applied to study the flotation reagents interaction with various mineral surfaces, eg of two common minerals from iron ores, kaolinite, and magnetite surfaces, or with fluorite surface, a tungsten ores common gangue mineral.

Aug 24, 2022

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023

By R Rimmelin, C Vergara

Heap leach pads are composed of mined ore, usually crushed, disposed on liners to be processed with leach solutions, and the tail of the process is called “spent ore” which are then transported by conveyor belts to be disposed into dumps. It is often to observe stability problems in these dumps, that could affect the equipment working on it and the continuity of the whole mine process. These problems are related to an excess of water content at the spent ore, therefore the operational efforts are focused onto control this geotechnical parameter.This work presents the results of different geotechnical laboratory testing, using samples of spent ore of a mining operation in the north of Chile. In the last 10 years, 3 campaigns have been made to get samples. Valuable information was obtained to identify how specific operational/metallurgical factors could affect the geotechnical behaviour of the spent ore. Special attention is given to the decision to change the metallurgical process adding salt to the heap leach process and its impact to its hydraulic conductivity.Historically, the process has been based on the leaching of oxides and sulphides materials, in separate campaigns, in which it is possible to observe different geotechnical response in the spent ore generated. Recently, it was implemented a new process in which the materials are blended and salt is added, to improve metallurgical performance in terms of recovery. This change generate impacts in the dump, since the geotechnical parameters are affected; decreasing hydraulic conductivity in about one order of magnitude (explained by the salt added).Changes are shown in the geotechnical parameters of the spent ore, considering that the mining source is the same, and how the operational process and dump design are affected.CITATION:Rimmelin, R and Vergara, C, 2018. Geotechnical behaviour of spent ore – impacts of metallurgical factors, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 369–375 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018