Search Documents

By J Furtney, W Fu, D Nutakor, A Brose

Rock blasting outcomes are often a shared responsibility of both the mine operations group and the mine geotechnical group. From an operational logistics and planning perspective, blasting concerns include optimal fragmentation for subsequent crushing, ensuring the blast is energetic enough to allow easy digging, and understanding the effect of muck from a previous blast on the current blast. From a geotechnical perspective, wall damage and catch bench capacity are the primary concerns. Other concerns for both teams include damage to mine infrastructure by fly rock or blast-induced vibrations, and the stability of open stopes under the pit. This work presents two blast modelling applications (or ‘apps’). The basic app instantly gives fragmentation and wall damage predictions for a given generic blast design. The advanced app loads the current pit contours, reads the blast design from a spreadsheet, and calculates the expected vibration magnitude and peak frequency. The apps have been developed specifically for the Rio Tinto Borates and Lithium Mine in California and are used to support blast design between the operations group and geotechnical group. The basic app instantly gives fragmentation and vibration predictions given a blast design by combining the Kuz-Ram fragmentation model with the scaled distance model for vibrations. The advanced app uses the signature hole method. Blasting outcomes at the mine have improved since using the apps.

Jun 22, 2022

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007

By A Purwodihardjo

Evaluation of the construction method used for the pedestrian underpass construction at Ipswich Road, Brisbane, Australia is presented in this paper. The pedestrian underpass was constructed through the existing railway embankment between Harrogate and O’Keefe Streets on the eastern side of Ipswich Road. This underpass construction is part of the CLEM7 tunnel project (formerly known as the North-South Bypass Tunnel) which is the longest toll road in Australia at a total length of 6.8 km. The jacked box construction technique was initially identified as a preferred option during the tender and concept design phases. However at the final design stage, the cut and cover technique was selected as this method can reduce the construction time and cost significantly. The design and construction teams effectively managed the challenges, complexities and risks associated with undertaking cut and cover tunnel through the existing heavily utilised rail embankment. The on-site construction time for the underpass using the cut and cover technique was reduced to less than 42 hours.

Mar 8, 2011

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By R Miller

The enrichment of magnetite to haematite and haematite-goethite leads to a coincident magnetic low and gravity high within the banded iron formation. Palaeochannel deposits of pisolitic limonite can be expected to provide a relative magnetic high and gravity low in a sinuous geometry. Detrital iron deposits of conglomerate, scree or ‘canga’ might have indistinct magnetic response but will usually have a relative gravity high.These signatures provide clear discriminators detectable by a joint gravity and magnetic survey.The combination of airborne gravity gradiometry and magnetometry is particularly powerful in detecting and discriminating targets, as well as mapping lithologies and structure, across a wide variety of iron ore deposit styles. It provides detection capabilities in a platform capable of rapid, complete coverage with minimal access issues. This approach has been used in FALCON™ airborne surveys for iron ore exploration in the Great Lakes, USA; the Middleback Ranges, South Australia; and the Hamersley Basin, Western Australia.The complex magnetic properties of iron formations (particularly remanence, anisotropy and depth of weathering) prevent this approach from being simple. The use of vector residual magnetic intensity (VRMI), calculated from the measured total magnetic intensity (TMI), assists by reducing the complexity due to the different directions of the remanent and induced magnetic fields.Estimations of the density to magnetisation ratio via the pseudo-lithology calculated from the VRMI and gravity gradients provide a useful method of capturing the discriminatory power of joint magnetic and gravity gradient data.

Jul 11, 2011

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By P Holt, M Allen

On the first of July, 2012, the Australian GovernmentÆs Clean Energy Act commenced. From this point, a price of $23/t of CO2-e will apply to facilities that trip the liability threshold. This first part of this paper concentrates on the mechanics of the Clean Energy Future legislation and how it will be applied to the mining and mineral processing industry.The second part of this paper contains analysis of the data presented for typical mine operations. Methodologies for constructing a carbon strategy are also presented. This will entail determining what the objectives of the carbon strategy are, and defining what the strategic priorities for a business should be. An action plan to address the risks identified from the Clean Energy Act is also developed as part of the strategy.Details such as the advantages and disadvantages of opting into the carbon price scheme for liquid fuels are shown. Other considerations such as the ability to acquire permits through the carbon farming initiative or through overseas clean development mechanism projects are explained.CITATION:Allen, M and Holt, P, 2012. Implications of the carbon price and developing a carbon strategy, in Proceedings International Mine Management 2012, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By S Talu, E Savage, S Howe

Major falls of ground, strainbursts, airblast and mudrush events are the major hazards in block caving environments, resulting in both safety and financial consequences and losses. Rio Tinto mines have developed strategies to reduce the likelihood of these events occurring. However, until recently, there have been no tools available to monitor and manage these hazards in real time.Mira Geoscience and Rio Tinto have collaborated to develop real-time geohazmaps to monitor and manage major cave hazards. These geohazmaps are used by mine planners to integrate multiple hazard parameters that contribute to form a combined hazard rating.The benefits of implementing geohazmaps include safety and cost improvements through the early identification of potential locations for major events. These cost savings are realised in the design phase, where development and critical infrastructure is located in areas of lower hazard rating. Additional improvements can be achieved by taking the hazard level into consideration when planning the production and development schedules and ground support design.CITATION:Talu, S, Savage, E and Howe, S, 2016. Geohazmap implementation in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 817–822 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By H Arvidson, A Walker, N Pollock

Following the recent tailings tragedy in Brumadinho, the Investor Mining and Tailings Safety Initiative was formed representing institutional investors in the mining industry. This Initiative, led by The Church of England (CoE), requested data from 726 mining companies on each of their Tailings Storage Facilities (TSFs). What this exercise confirmed was that there was no public database of TSFs, and that there was a clear gap in tailings management systems within the disclosing companies. We present an approach using technology to support best practice TSF management, governance and disclosure which was originally submitted as part of University of Cambridge Post-graduate studies in Sustainability Leadership in January 2020. The aim of the paper is to discuss how technology could be used to deliver a Tailings Management Solution (TMS) that is aligned with the Global Industry Standard on Tailings Management (GISTM), and supports rigorous governance leading to disclosure. Subsequently the goals of the plan are aligned with that of the co-conveners of the GISTM (the International Council on Mining and Metals (ICMM), Principles for Responsible Investment (PRI) and United Nations Environment Program (UNEP)) which is to facilitate operators’ trajectory towards zero harm to people and the environment. Most of the focus to date around tailings management post Brumadinho has been on monitoring technologies, of which there are many. It is obviously important to acknowledge the critical role of monitoring technologies; however, our approach is agnostic to monitoring technologies and assumes that all of them are relevant. Our focus is on the data management, reporting and governance leading to disclosure of the information. Critical components of developing the TMS include adapting existing software products and solutions, recognising a system thinking approach is needed, strategic partnerships to deliver an accessible solution faster and more cost effectively, and, new ways of collaborating. The TMS should also accommodate relevant regional geotechnical codes and standards. The industry need for a TMS is well established and urgent, with significant pressure from regulators and civil society for the industry to address this significant issue.

Jul 1, 2021

By A Li, H Jinto, M Laxman

The behaviour of tailings under cyclic loading has an impact on the stability and deformation of tailings dams and a good understanding of the cyclic behaviour of the tailings under earthquakes is important for tailings engineers and tailings operators for the design and safe operation of tailings dams. This paper presents an investigation into the cyclic behaviour of tailings using both laboratory cyclic direct simple shear (DSS) testing and numerical modelling. The laboratory testing involved cyclic DSS tests on gold tailings and zinc-copper tailings under different loadings and loading frequencies. The gold tailings specimen tested at a higher loading frequency and a higher cyclic stress ratio experienced spontaneous liquefaction during cyclic shearing and the zinc-copper tailings specimen tested at a lower loading frequency and a similar cyclic stress ratio exhibited ductile behaviour and liquefied due to cyclic mobility. The liquefaction behaviour of the tailings was modelled using an advanced constitutive model (UBCSAND), which was developed specifically to model soil liquefaction and strain softening under cyclic loading. The constitutive soil model presents the nonlinear soil behaviour under dynamic loading using a hyperbolic stress-strain relation. Dynamic analyses were carried out using a finite difference program FLAC. The cyclic stress-induced excess pore water pressures measured in the laboratory were modelled using numerical simulations of the laboratory tests under different loading conditions. The results of the non-linear dynamic analyses demonstrated the capability of numerical modelling of cyclic shearing induced excess pore water pressure and the onset of the spontaneous liquefaction. The laboratory investigation and numerical modelling technique provided the key properties and parameters for the dynamic analyses to assess the stability and deformation of tailings dams under design earthquake events. More importantly, the laboratory tests and numerical modelling provided some insights into liquefaction behaviour of the tailings during earthquakes. CITATION:Li, A, Laxman, M and Jinto, H, 2018. Liquefaction behaviour of tailings under cyclic simple shear testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 250–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018