Search Documents

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

Professional engineers of today require a wide array of experience and knowledge. It is true that commonly engineering degrees do teach the technical requirements well, but do fall short in the way of teaching other non-technical issues of professionalism to the student. Today calls for an engineer who does not only have a high standard of the technical knowledge required for their degree, but also has a broad range of experience in areas that are becoming increasingly important in engineering. The importance of social responsibility, liability and interpersonal relations is high. Through the face of the changing world, it has become clear that there is a need for a new type of engineer, who has a broad range of expertise, as well as the typical technical abilities required. This paper will outline these non-technical issues and propose ways of combining these ideas into the mainstream engineering degree.

Jan 1, 2004

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

By A Poliakov, E Donskoi, K Vining

The automated optical image analysis software Mineral4/Recognition4 (M4/R4) is capable of performing comprehensive characterisation of different materials throughout the iron ore value chain, including ore fines, lump, sinter, pellets and coke. It has been successfully used by CSIRO for industrial and research projects and has been independently licensed to several world leaders in iron ore production and ironmaking. The M4/R4 software was strongly integrated with a Zeiss microscope to make use of the company’s powerful AxioVision software. This required users to own both Zeiss microscope hardware and AxioVision software in order to be able to use M4/R4 to its full image acquisition and analysis capacity. Therefore, it was not available to the users of equipment produced by other major microscope manufacturers. In recent times however, Zeiss has indicated that the AxioVision software will no longer be supported. To overcome this limitation, CSIRO has proceeded with the next generation of this software, Mineral5/Recognition5 (M5/R5). Importantly, the M5/R5 system has been developed without any dependence on a specific microscope hardware/software platform. Furthermore, the image analysis functionality is now based on openCV open access software and has been fully rewritten using stateof- the-art software development tools to allow reading and processing of all major image formats. Although past applications have been specific to iron ore and ironmaking applications, other improvements, such as an increased number of minerals allowing better gangue segmentation, flexible mineral definitions, improved software modules behaviour and refined analysis routines enables the platform independent M5/R5 image analysis system to be used by researchers in any area of mineralogical or materials research.

Nov 8, 2021

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

By E Kasai, D Maruoka, Y Konno, T Murakami

The iron ore sintering process produces approximately three per cent of carbon dioxide emission in Japan because a large amount of coke breeze is used as the main agglomeration agent. Therefore, its suppression has been required. A promising method is to replace the coke breeze with biomass char and iron-bearing materials. In this study, the effect of the utilisation of metallic iron with coke or palm kernel shell char (PKS char) as an agglomeration agent on its oxidation behaviour was examined by a series of experiments using a sintering simulator. The use of PKS char leads to a larger decrease in the pressure drop difference of the sintering bed compared to the case using coke. Furthermore, the oxidation rate of metallic iron was larger in the case using PKS char together than that using coke. It was considered that the oxidation of metallic iron was promoted because the bed-temperature increased at a faster rate and achieved a higher temperature.

Nov 8, 2021

By C Augustin, M Hahn, K Nienhaus

Operators of mining machinery like haul trucks or excavators have very limited information about the exact distance to other equipment as well as to the natural boundaries like berms, walls and structures such as crushers. The industry is seeking solutions to provide safety and positioning. The authors have developed a solution approach which is being used in several installations. This solution consists of three parts: first robust and compact two-dimensional (2D) radar scanners that provide range and angular information of the environment especially under difficult conditions like dust, rain, snow and fog; second an intelligent data processing framework flexible enough to adopt to different machines and operation modes like speed, inclination, visibility, tire friction, GPS position, orientation and acceleration; and third a high quality and easy to use interface giving highly condensed data to the operator, not blinding the operator at night and being sunlight readable. The truth of present proximity detection sensors is that they not only have a high false alarm rate but furthermore cover only a fraction of the possible scenarios. This makes them unsuitable for stand-alone collision avoidance systems. On the other side, mine dispatch systems only deliver database and GPS information, but no information regarding the real environment. The indurad company and its Australian partner CTS (http://www.cts.com.au) addressed these aspects by developing smart productivity enhancement driver assistance tools like lane and crusher dumping assistance.An innovative driver assistance tool developed in cooperation with the coal shearer manufacturer Eickhoff and the RWTH Aachen University has been awarded with the annual research award of its customer RAG, being the largest German hard coal producer, as well as with the bauma Innovation Award in 2010.

Sep 26, 2011

By M I. Pownceby, N A. S Webster, J Manuel, N Ware

The properties of iron ore sinter – commonly defined by measures of tumble strength, reduction degradation and reducibility – have a major impact on blast furnace performance. These properties are largely influenced by raw material properties, in particular the bulk ore composition. Despite this importance, there is a lack of quantitative data on the impact of ore chemical composition on iron ore sintering. This is surprising since the levels of Fe, SiO2, Al2O3, P, MgO and other elements, together with the nature of the minerals in the fine ore, play a major role in determining the abundance and type of high-temperature bonding phases that form during sintering. It is the abundance and nature of the high-temperature bonding phase(s) that directly influences sinter quality. This study combines in situ diffraction experiments in model sinter systems with laboratory-based compact sinter tests using natural ores to examine the links between iron ore composition and sintering temperature and their effects on standard metallurgical sinter quality test methods. Results help to establish the critical compositional and thermal parameters that control the bonding phase chemistry, which in turn influences the physical characteristics of the sinter matrix. This information should enable operators to predict optimum sinter operating conditions based on the initial chemistry and mineralogy of the iron ore fines and recognise the chemical modifications to the original iron ore fines required to produce high-quality iron ore sinter.CITATION:Pownceby, M I, Webster, N A S, Manuel, J and Ware, N, 2015. Iron ore geometallurgy – examining the influence of ore composition on sinter phase mineralogy and sinter strength, in Proceedings Iron Ore 2015, pp 579–586 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The Mount Isa mine in North West Queens- land produces a total of nearly 10 million t/yr from separate copper and silver lead zinc orebodies. Sampling information is mainly obtained from diamond drilling on 30 to 40 metre centers in both types of orebodies. For the copper orebodies the majority of the core is analysed for copper content using a non-destructive bulk analyser developed by the Australian Atomic Energy Commission. The diamond drill core in the silver lead zinc orebodies is usually sam- pled as sawn half core and assayed in the com- pany laboratory using a variety of methods dependent upon the level of metal content and/or the elements required. Underground development is sampled where additional information is required to improve the ore reserve estimate. The copper areas are sampled using a standard 2.0 m by 2.0 m chip sample of the wall. The chips are taken on a 250 mm spacing. Lead areas are sampled using a 100 mm wide by 4 mm deep channel over intervals determined by the area geologists. The massive, irregularly shaped copper ore bodies are mined as large sublevel open stopes and pillars. Ore reserve estimation on both a production unit and global scale is routinely carried out using a geostatistical system developed in-house and running on a Sperry 1100 mainframe computer. Copper grade, tonnes and the Kriging var- iance are estimated at points on a user defined grid. The Kriging program uses 10 m assay composites from diamond drill core and underground chip samples. One average (rela- tive) variogram is used throughout the main copper orebodies. The validity of using an average variogram was verified by the original geostatistical study undertaken in the late 1970's.

Jan 1, 1987

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By D A. Kepert, I J. Tehnas, M A. Pudovsk

BHP Billiton (BHPB) was the first company to start iron ore mining in the Pilbara at Mt Goldsworthy in 1966 through Goldsworthy Mining Limited (GML - then Consolidated Goldfields Australia, Cyprus Mines and Utah). Operations later started at Newman on Mt Whaleback in 1969 with the Mt Newman Mining Joint Venture (MNM û then comprising American Metals Climax û AMAX, Colonial Sugar Refineries û CSR and BHP). In 1986 it acquired majority ownership of MNM, and at the same time the previously 100 per cent BHPB owned but undeveloped Yandi property came on board. Purchase of Jimblebar (formerly McCameyÆs Monster) occurred in 1990 and full ownership of Goldsworthy followed in 1991. With the exception of Jimblebar (100 per cent owned), all mines are now 85 per cent BHPB and the balance with Itochu and Mitsui. This evolution of the company resulted in an eclectic mix of mines/ores, each with their varied exploration and evaluation histories. Discussion of some aspects of these histories, and reflections on changes in exploration-related activities with particular reference to discussion of advances in geological understanding since the 1960s forms the basis of this paper. BHPB presently has open cut mines at four main centres û Newman, Jimblebar, Marillana Creek (Yandi) and Yarrie û and is currently developing the former GML Area C near Yandi. With the exception of NewmanÆs Mt Whaleback mine and immediate satellites, all are contract operated. Ore is carried on BHPB railroads (696 km total) for export through the companyÆs Nelson Point or Finucane Island shipping facilities at Port Hedland. Some is directed to the BHPB Boodarie Iron hot briquetted iron plant near Finucane Island. Over 73 Mt of ore was produced by BHPB in calendar 2001, and the company has now mined over 1500 Mt in Western Australia since their operations at Yampi Sound first started in 1956.

Jan 1, 2002

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

A Kellogg type computer model of the slag fuming process is applied in reverse to derive some thermodynamic properties of components in lead blast furnace slag. At 1200¦C, the average activity coefficients calculated were 3.40 (S.D. 0.50) for ZnO referred to the pure solid; 0.657 (S.D. 0.022) for PbO referred to the pure liquid; for the ratios y 3.175 y (referred to the Feo.9450, Fe304 pure solids) 4.19 (S.D. 1.15), and for yCaS/ 1CaO (referred to the pure solids) 5.10 (S.D. 2.96). Statistical relationships were derived for these activity coefficients and ratios as functions of the composition of slag, which contained in molar percentages 1.9 - 12.6% ZnO, 19.8 - 24.9% Fe0.9450, 0.9 - 1.6% Fe304, 0.002 - 1.9% PbO, 16.1 - 18.6% CaO, 25.9 - 31.0% SiO2, 4.8 - 5.5% MnO, 9.2 - 10.3% A101.5, 1.2 - 1.4% CaS, and 5.1 - 9.6% "Mgo" (the balance).

Jan 1, 1980

By Walton S, Wheeler D. J, Sargent D. M, Ting L. Y

Goonyella-Riverside mine is an open cut coal mine in Central Queensland. One component of the mining operations at this site is an uncompacted spoil dump some 50 m above the natural ground surface and over 300 ha in extent formed as a result of bucket wheel excavator operations. Plateau area slopes are 0.5¦ to 1.5¦ with irregular outer dump slopes of 9.5¦ - 17¦Investigation was undertaken and a series of trials planned to assess the suitability of a variety of stabilisation proposals to meet the client's requirements and to conform with Department of Resource Industrystabilisation guidelines.

Jan 1, 1992

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989

The Oregon-Idaho graben evolved after widespread Uwleiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17-16 Ma. The north- to north- northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1,100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcano- tectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma.

Jan 1, 1995

By P B. Card

"The website www.economicevaluation.com.au, which had its origins at the Project Evaluation Conference 2009, provides a free way for industry professionals to teach themselves economic evaluation. At its core is a set of fast-moving modules and three worked examples.The website recognises that economic evaluation is a discipline with a hierarchy of three levels:decision-makingevaluating the project/businesshands-on modelling.There are a set of modules for each level that describe the concepts and activities in detail. These emphasise that the most important and rewarding work is the evaluation of Level 2. The economic model created in Level 3 is merely a working tool and should not become a sophisticated ‘trophy’ in Excel that only one or two people can comfortably use.Hands-on modelling contains three sets of practices designed to make any model rigorous and intuitive so that it can be easily understood and used by others in the project team. Even if the model develops into a long, detailed and complex workbook, it should remain easy to follow and be intuitive. The website advocates freedom to devise any architecture that best suits the project under study, but promotes rigour through the following practices:four cash streams and graphsthree architectures – concept, prefeasibility and feasibilitysix principles.The modules in the Level 2 evaluation use conversational language to describe in detail the broad range of activities needed to properly understand and characterise a project/business. It stresses that net present value is nothing more than the mathematical treatment of a whole set of opinions, is not an absolute truth and is only a fraction of the evaluation process. The modules describe in detail the range of economic metrics that should be computed and the full spectrum of equally important characterisations required to make the decision in Level 3.CITATION:Card, P B, 2016. Teach yourself economic evaluation, in Proceedings Project Evaluation 2016, pp 160–171 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

The mining of Australia's rich and diverse mineral resources has been central to the development of the continent by "Europeans" over the past two hundred years. Mining has historically been encouraged (to varying degrees) by development-orientated state governments (the. managers of largely Crown-owned resources) and since Federation, by successive Com- monwealth governments (which have seen mineral development as a means of generating export revenue to fund predominantly social-welfare orien- tated budgets). This marriage of convenience between governments and the mining industry has to date served all parties well. However, Australia's entry to a new world economic environment at a time that community percep- tions are changing (owing to an education-inspired challenge to "old" values) is challenging the hitherto held assumption that mining develop- ment is always aligned with the well-being of the State and community. Issues such as the type and extent of State/Commonwealth government taxation, resource ownership and control, the environment, land use con- flict, the extent and desirability of secondary processing and infrastruc- ture funding are being debated in the public arena. Opponents of mining in the community are well-organised and are well funded, articulate and more importantly, they have effective communication channels with most governments, irrespective of political complexion. Apart from some television-orientated corporate image building and recent efforts by AMIC, the industry's response to this challenge has been unco-ordinated, poorly directed and arguably ineffective. Professionals working in the industry are concerned about the community's perception of themselves and their industry. Recognizing that the Australian democratic system ensures that, in the large, government at its various levels, is reflective of and responsive to the views and aspirations of people, the industry's response must be wide- ranging, equally articulate and couched in a form which is politically acceptable. New objectives in providing information to the public and its educators must be formulated. Moreover, professionals are looking for new directions from industry leaders. The Institute is well placed to facilitate this process.

Jan 1, 1988

Nordberg has conducted extensive research, during 1982-85, on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Nordberg's engineers have developed advanced design and testing techniques that ensure efficient and reliable crusher designs. Combination of this knowledge has resulted in a design of the MPI000 (1000 hp) crusher which fits on the existing 7ft Symons foundation and yet is capable of producing twice the ton- nage of the 7ft. In this paper the development of the MP1000 crusher and its performance compared to the 7ft heavy duty and super heavy duty crushers will be discussed. Also, substantial cost savings resulting from the application of such a high performance machine will be presented.

Jan 1, 1988

HISTORIC SIGNIFICANCE OF EXPLOSIVES TO MINERAL PRODUCTION The ancient method of breaking rock was to build a wood fire against the face, heat the rock through and then pour water on the heated ore-bearing rock to cause it to break by tension. It was too slow and costly as the forests around the mines were cleared and transport of wood became difficult. Black powder had been used for 300 years as a gun propel- lant. ('Black' after Berthold Schwartz, a German monk, Figure 1, and the inventor of the gun who was given the epitaph `Here lies Berthold the Black, the most abominable of inhumans who by his invention has brought misery to the rest of humanity'). Only at the beginning of the 17th Century, black powder was introduced for loosening rock in European mines. In 1802 Dupont started black powder manufacture on the Brandywine Creek. The ignition train of powder was enclosed in goose quills, straws, rushes, paper or wooden tubes. The time interval between igni- tion and blast was pure speculation.

Jan 1, 1988