Search Documents

By A Patwardhan, M M. Alam, K K. Thatavar

A commercial wet scrubber was used in the SIU-Joy dust control laboratory to test several concepts for improving the dust control efficiency of a wet scrubber. The concepts tested included two filter-two-spray systems, hollow and full-cone sprays, horizontal and vertical sprays, different layer filters and addition of surfactant. The optimised scrubber configuration had water-only vertical sprays for pre-wetting coarse dust, and vertical surfactant-laden water sprays for wetting ultrafine particles. This scrubber configuration reduced dust concentrations from 250 mg/m3 to 1.8 mg/m3. In comparison, the conventional scrubber configuration in the feed provides an outlet dust concentration of 3 - 4 mg/m3 in field operation. Upon successful testing and optimisation of parameters in the laboratory, field demonstration of the concepts was conducted at an Illinois coal mine. The optimised scrubber configuration was tested in the field with good results in terms of improved visibility in the face area and reduced respirable and quartz dust concentrations. Additional modifications in the field involved relocation of the scrubber suction inlets from the bottom to the side and changing the water spray configuration on the miner head. These additional changes were based on a conceptualised spatial dust distribution profile in the face area. The results of these laboratory development and field demonstration studies are presented in this paper.

Jan 1, 2005

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By S A. Ravishankar, W Perez

Flotation is one of the main concentration processes to purify kaolin clay via the removal of naturally occurring impurity minerals containing Ti and Fe. Currently, there are two types of collector chemistries used in the industry to float coloured impurity minerals. These are traditional tall oil fatty acids (TOFA) and specialty hydroxamate (AHX) based collectors. AHX based collectors have long been known to be the most selective collectors to float Ti and Fe based coloured impurity minerals (CIMs) as compared to TOFA based systems. AHX based collectors provide, not only improved selectivity and simplified process, but also more importantly, make it possible to treat certain kaolin resources that do not respond to standard TOFA systems. However, the relatively higher cost of straight AHX collectors has restricted broader application of these collectors in kaolin clay and other oxide flotation applications for a long time. Recent technological advancements, in both making and formulating AHX products more economically, increased the usage of these collectors in kaolin applications. Modified AHX products offer more economical alternatives and process options to provide high purity kaolin clay products for specialty applications based on cost-performance criteria. In this paper, the flotation performance of a series of newly developed AHX formulations is provided along with the characteristics of AHX flotation in general. In addition, flotation performance of earlier AHX collectors is provided based on published literature as background data.

Jan 1, 2005

By G M. Evans, C M. Phan

This paper presents an analysis on the dynamic adsorption of frothers and collectors onto air bubbles in flotation. The analysis was carried out using the theory on the surfactant transfer by diffusion and adsorption. The bubble size was considered when solving the diffusion equation for the dynamic surface excess. The adsorption kinetics was modelled employing the Langmuir adsorption isotherm and its extension with the inclusion of the lateral interaction of the adsorbed molecules (the Frumkin adsorption isotherm). The numerical computation was applied to solve the governing equations. The dynamic adsorption of the surfactants was measured in terms of the dynamic surface tension for sodium dodecylbenzene sulfonate (SDBS) and Dowfroth 250, using pendant bubble tensiometry. The results show that for air bubbles with diameter of the order of 1 mm, the bubble size effect on the dynamic surface tension is small and the solution of the diffusion equation for a planar gas-liquid surface can be used to describe the dynamic adsorption onto the air bubbles. The experimental data obtained with SDBS were well described by the Frumkin adsorption isotherm and the molecular diffusion. The model description for the experimental data obtained with Dowfroth 250 required the kinetic equations. The paper is relevant for further analysis of the role of the adsorbed surfactants in the particle collection.

Jan 1, 2005

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

By Y Cao, J C. Tien

Occupational health and safety is essential in modern mining workplaces and in China it is often not given enough emphasis due to a lack of knowledge and/or appreciation. Although many health and safety regulations have been passed over the years, serious and relevant laws and regulations on mine health and safety are of recent history (since 2002), the level of stringent enforcement is still inconsistent and accurate field data are scant and not readily available. As of year-end 2006 there were 676 562 recorded cases of occupational diseases in China, of which 616 442 or 91 per cent were miners’ pneumoconiosis. Of these, 146 195 (23 per cent) have died, and an average of 10 000 new cases were added every year between 1991 and 2006. Another report shows that 93.18 per cent of miners have never had a contract with their companies, which means their cases were not even part of China’s official statistics. This study attempts to examine the prevalence of occupational diseases in the Chinese mining industry during 2000–2013, compiled from government annual reports and academic studies. The research will review the correlational analysis among occupational diseases, ventilation practices, protection devices and legislation.CITATION:Cao, Y and Tien, J C, 2015. Occupational diseases in China, with the emphasis on its occurrence in Chinese mine workers, in Proceedings The Australian Mine Ventilation Conference, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By Shillabeer J

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

By F Radke, P A. Tilyard

Determination of the mineralogical location (deportment) of minor and trace elements (including credit and penalty elements) in base metal concentrates can indicate whether further processing is likely to (a) reduce the levels of the penalty elements, and/or (b) direct selected elements into other plant products, thereby increasing current concentrate grade or increasing payment for credit elements. To determine the deportment of elements requires knowledge of the proportions of the minerals present and their individual element contents. In addition, knowledge of the liberation and locking is important, as this can affect any possible further processing. Mineral proportions can be determined by a variety of methods including chemical analysis, point-counting, area-counting, QEM*SEM, image analysis and mineral separation. In the case of a Broken Hill zinc concentrate, several of these methods were used and gave consistent results.

Jan 1, 1998

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By White A. H, Gillies A. D S

In recent years the Australian gold industry has gone through a major expansion phase. The need for finance has led to adoption of different approaches such as the well known gold loan, forward selling, equity participation by suppliers and equipment leasing. During early periods of the expansion, significant new equity was raised chiefly for high risk exploration ventures. The major form of new equity finance was ordinary shares, often in 'No Liability' companies. The increasing capital requirement of the huge new development projects of the 1980s also spurred the use of debt finance. This trend was accelerated as high inflation and the taxation advantages of debt finance made borrowing attractive. This paper reviews major financing techniques used by the Australian gold industry with particular emphasis on the innovative financing techniques initiated recently. An analysis has been undertaken of the effects on the industry of issues such gold loans, forward selling, equity participation by suppliers, fly-in fly-out operations, contractor mining and equipment leasing. In order to achieve a better understanding of the innovative financing techniques, a survey of already published financial data from well known Australian gold mines was carried out. Data was collected from various published financial reports of gold mining companies. In addition, a questionnaire survey was sent to gold mining companies to assist the collection of further information. The results of this study show that there are a significant number of gold mines variously using gold loans, forward sales, contractor mining and fly-in and fly-out arrangements to finance their projects. Only four operations have vendor suppliers investing capital funds in their projects. Based on the findings of this study, conclusions and recommendations are drawn that these approaches are likely to be with Australian gold industry for some time in the future and will continue to be intensively applied to finance gold projects.

Jan 1, 1994

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

By Pak DL

Over the last decade computers have become an essential element in assessing the economic feasibility of mining new mineral deposits and in assisting a variety of related support functions. A broad overview is given of the many technical application areas where computers are contributing to the mining industry with reference to work being done on the evaluation of drill hole information, mineral inventory modelling, ore reserve estimation, financial analysis, process simulation, process control, workshop job scheduling, PERT applications, and com- puter aided drafting. In all these areas the computer has greatly reduced the manual effort involved in looking at alternatives. It has had a significant effect in eliminating delays in revising calculations, or rescheduling activities to incorporate new data or cater for changing conditions, while at the same time providing more accurate and prompt information for the management decision making Process.

Jan 1, 1980

Byproduct coking is practised in three of the major Australian ironmaking centres, the Newcastle and Whyalla works of the Broken Hill Proprietary Co. Ltd. and the Port Kembla works of Australian Iron & Steel Pty. Ltd. Coking first commenced at Newcastle in 1915 and at Port Kembla in 1938. The installations established at these centres include coal cleaning facilities and com- plete byproduct streams. The Whyalla plant, because of its location is somewhat less extensive, having no coal cleaning plant and a comparatively restricted byproduct section. As new batteries have been built every opportunity has been taken to incorporate modern design features and improved operat- ing techniques. This has included the provision of equipment to reduce atmospheric and water pollution. A marked reduction of markets for byproducts has had serious repercussions on the profitability of this section of the Industry.

Jan 1, 1972

By B Hou

The Eucla Basin in southern Australia is emerging as an important global source of zircon from heavy mineral sands. Understanding the geological evolution of the basin and movement of heavy minerals down peripheral paleovalleys and along paleocoastlines is essential to effectively refine exploration strategies for heavy minerals in the basin. Integration of geoscientific datasets in a Geographic Information System (GIS) environment has proved to be effective in reconstructing depositional environments along the Cenozoic basin margin and in tracing the buried paleorivers that once drained broad areas of the Archean-Paleoproterozoic Yilgarn and Gawler cratons, the dominantly Mesoproterozoic Musgrave and Albany-Fraser Provinces, and the Neoproterozoic-Early Paleozoic Officer Basin. Sea level highstands during the late Middle Eocene (39 - 36 Ma) are associated with formation of the Ooldea coastal barrier complex and the zircon-rich heavy mineral deposits at Jacinth, Ambrosia and Tripitaka. More extensive transgression during the Late Eocene (36 - 34 Ma) built the complex Barton shorelines that host the Cyclone deposit and the extensive ilmenite-dominated occurrences of the Barton West prospect. Multi-generation reworking of the source sands is indicated by the high proportion of deposits that are zircon-rich relative to titanium minerals. The age distribution of zircon grains in heavy mineral concentrates from the Ooldea and Barton barrier systems points to the Musgrave Province as the predominant ultimate zircon source. Paleorivers discharging along the northern basin margin presumably carried a sediment load that was then redistributed by easterly longshore drift to build the extensive coastal sand deposits along the northern and eastern basin margin. The south-eastern extension of these deposits was reworked during Miocene-Pliocene (15 - 2 Ma) times into a series of regressive strandlines that show angular discordance with the Eocene coastlines. This discordance is consistent with evidence for long-wavelength tilting of the Australian continent from Middle Miocene times, as the continent drifted toward a dynamic topographic low induced by convective mantle processes associated with the South East Asia subduction systems. The Dromedary and Gulliver’s deposits probably formed at this time. Ongoing research is focused on the geological features of the basin that influence heavy mineral transport, concentration and preservation, and the processes leading to deposits with high zircon content.

Oct 5, 2011

Almost all the countries of the south-west Pacific and the Australian states have recently completed or have commissioned mineral royalty reviews. The prime reasons for this widespread and consistent action is the desire of the governments of these entities to redress perceived effi- ciency and equity imbalances and to ensure that the revenue raising motive does not override the necessity to maintain mineral exploration and development incentives. Governments are tending to adopt royalty systems comprising a com- bination of base royalty and a profit component. Resource rent royalty and royalty holidays have been introduced and anomalies, such as royalty free gold production, still exist but appear to have uncertain futures. Tasmania ranks as the Australian state with the lowest aggregate royalty levy/production value ratio whilst Papua New Guinea has the highest royalty objective achievement level in the south-west Pacific region.

Jan 1, 1988