Search Documents

By L. W. Holm

This study shows that in the presence of foam, gas and liquid flow separately through porous media representative of reservoir rock. These results were obtained by using tracer techniques to measure the flow of the gas and liquid comprising the foam. Foam does not flow through the porous medium as a body even when the liquid and gas are combined outside the system and injected as foam. Instead, the liquid and gas forming the foam separate as the foam films break and then re-form in the porous system. Liquid moves through the porous medium via the film network of the bubbles and gas moves progressively through the system by breaking and re-forming bubbles throughout the length of the flow path. The flow rates of the gas and liquid are a function of the number and strength of the films in the porous medium. There is no free flow of gas; i.e., no continuous gas phase. On the basis of these results, foam can be expected to improve a water flood or gas drive by decreasing the permeability of the reseruoir rock to a displacing liquid or gas. This improves the mobility ratio and thus the conformance of the flood. INTRODUCTION Foam is formed when gas and a solution of a surface active agent are injected into a porous medium either simultaneously or intermittently. During the past few years, several papers have been published on the subject of foam flow in Dorous media. Foam has been used successfully in the removal of capillary water blocks from producing formations.''2 The use of foam in gas storage reservoirs to reduce gas leaks and to increase storage capacity has been considered in recent years. Foam has also been investigated as an oil displacing agent,3-5 and as an agent to improve the mobility ratio in a waterflood.6-10 However, the mechanism by which the gas and liquid phases comprising the foam flow through a porous medium has nor been described adequately. Normally, when two immiscible phases (gas and liquid) flow concurrently through a porous medium, each phase follows separate paths or channels. At given saturations of the two phases, a certain number of channels are available to each phase, and as saturations change, the number and configuration of the channels available for each phase also change. The effective permeability of each phase is a function of the saturation of that phase only, and the flow of each phase can be described by Darcy's law. When foam is present, the effective permeability of the porous medium to each phase is greatly reduced compaced with permeabilities measured in the absence of foam.6,11-13 Based upon the observed flow of surfactant solutions and gas in capillaries, it has been concluded that the gas and liquid may flow separately or they may flow combined as foam. At least four mechanisms have been postulated to explain how fluids flow with foam present: 1. A large portion of the gas is trapped in the porous medium and a small fraction flows as free gas, following Darcy's law.9 2. The foam structure moves as a body; the rate of gas flow is the same as the rate of liquid flow. 6,13 3. Gas flows as a discontinuous phase by breaking and re-forming films. Liquid flows as a free phase.12 4. A portion of the liquid and gas move as a foam body while excess surfactant solution moves as a free phase.14 It also has been suggested that different flow mechanisms exist for high quality (dry) foams made from dilute surfactant solutions and for foams made from more concentrated solutions. Studies conducted on the flow of foam through capillaries have shown that a plug-type flow occurs and that foam flows as a body.6,15 Fried also has described the flow of foam through porous media as

Jan 1, 1969

By M. T. Hepworth, W. B. Sample

HYDROGEN solubility and linear contraction measurements were made at constant temperature on an alloy of titanium of constant oxygen-to-titanium molal ratio but variable hydrogen content. A cylindrical specimen of titanium (0.25 by 1.6 in.) containing 0.75 at. pct 0 and less than 0.03 at. pct N was cast from a master button of iodide process titanium which had been alloyed with titanium dioxide. Four vacuum fusion analyses, which were made along the length of the cylinder after the hydrogen solubility studies were made, revealed a variation of oxygen content of less than 0.02 at. pct. The specimen was introduced into a quartz furnace tube, annealed and outgassedat 1050"~ for about 1 hr, and then held at 800" * 0.5" for about 30 hr, during which latter time experimental data were taken. The leak rate to the furnace chamber was not sufficient to contaminate the specimen during the run as determined by leak-rate studies and vacuum fusion analyses for oxygen and nitrogen before and after the runs. The furnace chamber was attached to a modified Sieverts apparatus used to introduce measured quantities of purified hydrogen to the specimen. A quartz pushrod transmitted changes in length of the specimen to a Chevenard dilatometer. The push-rod passed through a vacuum grease seal to the dilatometer which amplified motion of the rod by a factor of 319. During hydrogen addition, the pushrod did not contact the specimen. Measured quantities of hydrogen were added to the specimen and equilibrium hydrogen pressures recorded as a function of hydrogen content. The solubility data, which appear in Fig. 1, agree well with a separate investigation made with a different apparatus. The solubility limit of the hcp a phase appears as an abrupt discontinuity in slope at 3.4 at. pct H. The solubility plot has been extended as a dashed line at this discontinuity in order to emphasize the discontinuity. The hydrogen content at which bcc P appears is not clearly defined. An arrow indicates solubility data were taken upon hydrogen addition. Upon reaching the arbitrary maximum hydrogen content of the run, the quartz pushrod was pressed against the specimen in order to record the change in length with hydrogen removal. A pressure of about 100 g per sq cm was required to overcome the friction of the vacuum seal in order to obtain reproducible linear contraction data. The contraction ratio ~2/1", change in length divided by original length, was set equal to zero for the maximum hydrogen content. The relative contraction of the specimen was observed upon removal of hydrogen in the following manner. The system was opened to the pumps for a few seconds and an unknown quantity of hydrogen was removed. The system was then isolated from the pumps by closing a stopcock and allowed to return to equilibrium. When the temperature returned to 800°C, the pressure stabilized, and contraction ceased, measurements of contraction and pressure were made. The hydrogen content of the specimen was then deduced by measuring the equilibrium PIydrogen pressure and referring to the solubility plot. Linear contraction was then plotted against interpolated values of atomic percent hydrogen. The justification for this procedure is the established reversibility of the hydrogen equilibrium.' Uniaxial compression was assumed to have no effect on hydrogen pressure. The isothermal linear contraction data are plotted on Fig. 1. An arrow indicates data were taken upon removal of hydrogen. The solubility limits of the two phase a i /3 region can be identified by discontinuities ill slope of the dilatometric plot at 9.1 and 3.4 at. pct H, agreeing well with other studies.' Dashed extensions of the plots emphasize the discontinuities. Isothermal studies of expansion made upon hydrogen addition gave curves of much smaller slope and less pronounced discontinuities. A uniaxial compressive stress tends to accentuate volume changes in going from the more open bcc phase to the hcp phase.2 Incomplete data on ex-

Jan 1, 1962

By J. J. Gilman

RECENT experiments have shown that the mar-tensite reaction in a standard tool steel is influenced by the history of the reacting austenite. The martensite reaction proceeds to a given extent at a higher temperature in austenite formed from an annealed spheroidal structure than it does in austenite formed from tempered martensite: that is to say, a prequench lowers the temperature range of the martensite reaction in this steel. Furthermore, a prequench alters the appearance of the martensite as compared to martensite formed from "virgin" austenite. The steel used for this work was a manganese nondeforming tool steel of the following composition: C, 0.85 pct; Mn, 1.43; Si, 0.23; Ni, 0.12; Cr, 0.59; and W, 0.59. A piece from a rolled bar was forged to Vz in. sq and annealed to a spheroidal structure. Disks 1/8 in. thick were used in the experiments. Several sets of the specimens were prepared and austenitized in lead at 1475°F. Three sets were held at 1475°F for 15 min, quenched in water, and immediately reheated to 1475°F. After this quench the three sets were held for 5 min, 30 min, and 3 hr, respectively, at 1475°F and then the individual specimens in each set were quenched in molten baths to 325", 300°, and 275ºF, respectively, and held for 15 sec. Immediately after the quenching treatments? the specimens were tempered at 600°F for 30 sec to darken the martensite and then were quenched in water. The holding times were short enough to avoid isothermal transformation. Three other sets of specimens were given the same final quenching treatments as the first three, but they were austenitized at 1475°F for 20 min, 35 min, and 3 hr and 15 min, respectively, without an intermediate water quench. The two individual specimens from each set were quenched together in order to eliminate quenching errors. Several experiments were run in this way but only the six sets referred to are described in detail because they all yielded essentially the same results. By means of the stated heat treatments the martensite reaction was investigated for: 1—austenite formed from an annealed structure, and 2— austenite formed from tempered martensite. The martensite reactions of the two types of austenite differed significantly. This is shown by Figs. 1 and 2. Comparison of the photographs on the left in Figs. 1 and 2 with those on the right shows that less martensite was formed by a quench to a given temperature from prequenched austenite than from austenite formed from an annealed structure, that is, the prequench suppressed the martensite reaction. The effect was observed for specimens austenitized 20 min, 35 min, and 3 hr and 15 min. A comparison of Figs. 1 and 2 shows that the martensite reactions in both sets of specimens occurred at lower temperatures with increased austenitization time. This was caused by the increased dissolution of residual carbides with time at 1475°F. However, the difference in amount of martensite formed in prequenched austenite as compared to virgin austenite was approximately the same for all three austenitization times. One further observation should be noted. The needles of the martensite formed from virgin austenite are somewhat longer on the average and show less of a tendency to cluster than those of martensite formed from prequenched austenite. This causes the martensite on the right in Figs. 1 and 2 to have a more acicular appearance than the martensite on the left. Since the sets of specimens used in this work were austenitized for identical total lengths of time and the effect of a prequench on the martensite reaction existed for specimens held at the austenitizing tem-

Jan 1, 1953

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.' One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.'.' While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham's law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By Charles C. Towle, Irving Rapaport

URANIUM mineralization along the north flank of the Zuni Uplift, in the vicinity of Haystack Butte, was discovered by Paddy Martinez, a Navajo Indian, in the spring of 1950. The find was reported to the Santa Fe Railway Co., which initiated a program of exploration upon its holdings in the district in December of 1950. The Anaconda Copper Mining Co. secured numerous leases in January and February, 1951, and began an intensive exploration and development program in March 1951. The district was extended into the Lucero Uplift in August of 1951 by the discovery of uranium mineralization in Todilto limestone by Joy Sinyella, a Supai Indian living on the Laguna Reservation. Initial reconnaissance was performed in the district by the Atomic Energy Commission in November 1950. A field office under the direction of the Denver Exploration Branch of the AEC was established at Prewitt, N. Mex. in January 1951 to study regional and detailed guides to ore, to evaluate the ore deposits, and to promote the development of the district by providing geologic services for the companies and individuals engaged in exploration. With the development of sufficient ore to warrant construction of a mill, the Grants area of New Mexico has come of age as a full fledged uranium mining district. The carnotite-type deposits of Grants, the first of major economic importance found in limestone, have extended the Colorado Plateau carnotite field into the more complex structure of the Basin and Range Province. General Geology The Grants uranium district is in northwestern New Mexico, along the southern flank of the San Juan Basin, between the cities of Gallup and Albuquerque. The region is at a mean altitude of about 6800 ft, vegetation is sparse, and outcrops are excellent. Mt. Taylor volcanic peak, at an elevation of 11,400 ft dominates the surrounding area. The overlying cliff-forming Dakota sandstone is the most resistant formation in the Grants District and characteristically erodes into dissected mesas as much as five miles wide. The principle uranium ore-bearing horizons are found in the underlying Morrison formation, and the Todilto limestone of the San Rafael group. The Morrison weathers into. a series of steep slopes and precipitous cliffs near the lower part of the Dakota-capped rims, while in contrast, the relatively resistant underlying. Todilto [ ] limestone forms broad benches extending out from the base of these Dakota rims as much as five miles wide. The Todilto benches are covered with overburden to an average depth of about 5 ft in the first thousand ft away from the Dakota rim, but increases to about 200 ft at the base of the rim. In many places however, a thick mantle of upper Cretaceous sediments and Tertiary volcanics "obscures the ore-bearing Jurassic, and precludes exploration. . The known uranium deposits of the Grants District are distributed throughout a zone 85 miles long and about 10 miles wide. Stratigraphy Rocks from pre-Cambrian through Tertiary are exposed in the uplifted areas, but uranium appears to be restricted chiefly to two zones in Jurassic sediments. The Jurassic sediments of the Colorado Plateau have been subdivided into three units, in ascending order: (1) Glen Canyon group, (2) San Rafael group, (3) Morrison formation. The Todilto limestone zone within the San Rafael group has produced the bulk of ore to date, but the promise of the Morrison zone is rapidly increasing. The Todilto formation extends about 300 miles east-west and about 100 miles in a north-south direction. It is composed of a lower, extensive, limestone member and a central, more restricted, thick, pure gypsum member. The Todilto is believed to be of lacustrine origin. The Morrison formation in this area is subdivided, rather arbitrarily, into three members: Recapture Creek, Westwater Canyon, and Brushy Basin. Ore

Jan 1, 1952

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble's results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By T. J. Whalen, M. Humenik

The liquid surface tension of copper-nickel ad copper-nickel-titanium-carbon alloys and the wettability of titanium caybyde by these alloys have been measuhed. It was found that the surface tensions of the binary copper-nickel alloys Lie on a smooth curve between the end members, copper and nickel. The addition of small amounts of titanium and carbon has nO effect on the surface tensions of copper-nickel alloys. Small additions of nickel to copper significantly reduce the contact angle of Ike alloy with titanium carbide. From a Gibbs treatment, nickel is shown to be adsorbed at the titanium carbide-alloy interface. X HE microstructure of two-phase materials has been shown to be influenced largely by the interfacial energies between the phases present.' , In systems prepared by powder metallurgy techniques and densi-fied in the presence of liquid phase, a precise analysis of microstructure and interfacial energy relationships requires a knowledge of the solid-solid interface energies and liquid-solid interface energies. However, marly metal-nonmetal systems are characterized by the "sweating" of the liquid during sintering, and in these systems wettability is a principal consideration. The wetting in turn is dictated by the various interface energies of the system, as shown in Fig. 1 for a liquid drop formed on a solid substrate. The equation which expresses the vectorial balance of surface forces in the horizontal plane, at the point of contact, A, is given by: where ssv = solid-vapor interface energy sSL = solid-liquid interface energy sLV= liquid-vapor interface energy 6 = contact angle measured through the liquid phase. The angle and the surface tension, slv, can be measured accurately by the sessile drop method.3, The absolute value of the surface energy of the solid cannot be determined by this method, but with reasonable changes in the composition of the liquid only, the value of ssv can be considered constant. The changes in contact angle, then, can be attributed to changes in sSL and sLV and since sLV can be measured, the changes in sSL can be determined. Several studies have indicated that the surface and bulk properties of solid alloys can be correlated with electronic structure. The catalytic activity of copper-nickel alloys was reported to follow the dband vacancies in these alloys.5 Nickel has been considered to have 0.6 holes per atom in the d-band. The addition of copper to nickel is thought to bring about a filling of the d-band of nickel, since each copper atom contributes one electron. Thus, at an atomic concentration of 60 Cu-40 Ni (62 wt pct Cu-38 wt pct Ni) the d-band is believed to be full, and magnetic measurements support this view.6 If the electronic structure is influencing a property of the alloy, this property should show some sort of discontinuity as the composition changes from one side of the 60 Cu-40 Ni composition to the other. Since the catalytic activity can be considered as a surface property of the alloy, it is logical to assume that other surface properties, such as surface tension, may also be influenced by electronic structure. The suggestion has been made that there is a correlation between the solid titanium carbide-liquid Cu-Ni alloy interfacial energy and d-band filling.7 One purpose of this investigation was to determine if the changes taking place in the electronic structure with compositional changes in the solid copper-nickel alloys were reflected in the surface tension values of the liquid alloys. Such a change, if present, would lend support to the suggestion that one can refer to discrete energy bands in the liquid state. Other purposes of the present study were to investigate in detail the wettability in the system copper-nickel-titanium carbide, and to discuss the possible processes which take place during wetting in this system.

Jan 1, 1961

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper' reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.' This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.' The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work' is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By Robert L. Davidoff

INTRODUCTION The impact of taxation differs substantially from state to state in a complex fashion that depends on both the physical characteristics of a mineral deposit and on the price of the mineral commodity relative to its costs of production. A comparative analysis of the tax structures of eight states (Arizona, Colorado, Idaho, Montana, Nevada, New Mexico, Utah and Wisconsin) showed wide variations in rates of return for any given type of mineral property, with no state having either the most burdensome or least burdensome tax structure under all circumstances. Three hypothetical mineral operations were analyzed: a producing open-pit copper property, a non-producing underground platinum operation, and a non-producing underground gold operation. None of them corresponds exactly to an existing property. Each of these property types is further defined to have ore feed grades at three different levels, leading to three potential profitability levels, referred to in this paper as "economic", "marginal" and "subeconomic". Thus the differential impact of state tax structures is measured for mineral properties of different types, as well as for different profitability levels. Montana is used as the base case. This study does not address the topic of corporate structures or tax consolidation. There are no costs assumed external to the operation of the deposit (e.g. exploration to locate additional deposits). Two types of analyses were performed for this study. The first calculates the total cumulative tax payments in each state using all applicable taxes (including U.S. federal income taxes and examines the resultant differences in discounted cash-flows rate of returns DCFROR's amoung the eight states. The second is a sensitivity analysis that examines each type of state tax separately (i.e. state income, property, and severance taxes) in order to isolate and examine the differences in tax payments that are due to the difference in rates and methods of computing specific types of taxes in each state. The results of this study serve to illustrate the complex nature of interactions among various taxes. For example, property tax is a deduction in calculating severance tax in some state. Changes in property-tax and severance-tax payments both enter into the calculation of state and federal income-tax liability. This, in turn, could change the timing and usage of tax-loss carry forward amounts and investment tax credits. Additionally, the physical characteristics of a property, the method and costs at which the mineral will be extracted, and the profitability level at which each property operates will affect tax treatment. Each mineral operation was evaluated at three different predetermined profitability levels, referred to using the terms economic, marginal and sub-economic. These three profitability levels are defined by the ore feed grades of the primary commodity that yield in constant terms, approximately an "economic" 18% DCFROR, "a marginal." 10% DCFROR, and a "sub-economic" 5% DCFROR, respectively, under the Montana tax structure. In the analyses, the mining and processing parameters for each of the three types of properties were assumed to be identical for each of the eight states. It was assumed that each operation produces at full operating capacity throughout its life. This implies the level of mineral commodity demand will support the inferred commodity price, such that each operation will be able to sell all its output. The analyses performed for this study were done using a comprehensive economic evaluation simulator that is used in the Bureau of Mines, Division of Minerals Availability MAS program to perform DCFROR analyses. All economic evaluations performed upon these data (see appendix 2) were in constant January 1981 dollars. By-product prices used for the analyses were: [Gold $425.00/troy ounce Palladium$200.00/troy ounce Silver $ 10.00/troy ounce] Typical cash-flow calculation layout is given in Appendix 3. The initial step for each evaluation is to define an "economic" profitability level scenario. An 18% DCFROR rate in Montana was considered the

Jan 1, 1985

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By H. F. Webster, C. G. Dunn

Rolling md annealing procedures are described for developing the (110) preferred orientation in tantalum for use as a thermionic-emission materinl where electrodes of a uniform high work function are needed. The development of a (110) [001] annealing texture is also reported. A preferential growth process due to low (110) gas-metal surface energy is considered in explanation of the observed growth of (110) grains. ThE growth of (110)-oriented grains in thin strips of rolled zone-refined tantalum, previously discussed briefly,' is reported together with more recent information on the formation of a (110)[001.] annealing texture, i.e., one where the [001] direction of each grain lies close to the rolling direction. The development of tantalum sheet with a (110) preferred orientation (position of [001 ] directions unspecified) is of importance as a thermionic-emission material in thermionic-energy converters. Since therm ionic-emission properties of cesium-coated crystals vary over a wide range depending on (hkl) a2-7 a single (hkl) preferred orientation is more useful than either several preferred orientations or none. Furthermore, the (110) preferred orientation yields the highest thermionic-emission density for a cesium coverage of less than a monolayer.5-7 A consideration of the stability of the grain structure needed at high operating temperatures suggests that the preferred orientation itself should be produced by annealing processes. Information on annealing textures in tantalum, however, is rather limited. Pugh and Hibbard 8 obtained (111)[112] and (lll)[112] components in a 1400°C recrystallization texture in 95 pct cold-rolled foil; these components were enhanced on annealing at 2500°C. Muller9 rolled 99.97 Ta to 90 pct reduction in thickness in the final stage and noted only a slight sharpening of the rolling texture, with some intensification of the (111)[112] component upon annealing at 1200°C. The experimental procedure followed in the present work stemmed from the idea of using possible differences in (hkl) surface energies to provide a small driving force for growth of grains having the lowest (hkl) surface energy.l0* This would mean using high-purity tantalum processed into thin sheet form and annealed at high temperatures either in a noncontaminating atmosphere or in one producing additional sample purification. EXPERIMENTAL Zone-Refined Tantalum. National Research Corp. tantalum in the form of 1/8-in.-diam rod and of 99.98 purity (53 ppm 0, 15 ppm N, and 8 ppm C) was zone-melted four times. The traversing speed was 4 mm per min. Such treatment increased the resistance ratio, R293k/R20K , where R293K is the resistance of the specimen at 20°C and R20K the re-resistance at liquid-hydrogen temperature, from a value of 25 for the initial rod to 175 for the zone-refined rod (the increase in the resistance ratio provides a measure of purification11,12). Part of a zone-refined rod was rolled unidirec-tionally to a strip 0.003 in. thick and 0.28 in. wide. Samples were given anneals in the range 1300" to 2100°C using ac conduction heating in an oil-free vacuum system. Recrystallization to small grains appeared to be complete at 1300°C. Large grains were formed at higher temperatures, but these were not entirely strain-free, some grains showing asterism in Laue X-ray patterns and some displaying a range in orientation. Part of the difficulty was caused by thermal expansion of the tantalum strip as it was held between fixed supports. However, in a different arrangement with the tantalum freely suspended in a tantalum can, high-frequency induction heating in vacuo at about l0-6 Torr produced

Jan 1, 1964

By R. Schuhmann

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) In his excellent paper, Dr. Schuhmann has proposed a mechanism for conlrninution which can be utilized to explain a number of phenomena which have been observed in the size reduction of solids. The difference between the product obtained from a ball mill and from a rod mill can readily be explained by Dr. Schuhmann's hypothesis. Consider that the size distribution of the product from each comminution event is given by y; - 100 (x/ki) (1) where Yi is the cumulative percent finer than size x, ki is the size modulus, and is the distribution modulus for the single comminution event. The total product from a cornminution operation will be the summation of the products from all of the individual cornrninution events. If the size moduli from the various comminution events range from kl to kn , the size distribution of the total product will be a straight line on a log-log plot only to a particle size equal to k ,. Considering 100 volurnes of feed, the value of y for x equal to kl is Riven by where y is the cumulative percent finer than size kj, z is the number of comminution events of kind i, and vi is the volume of each particle crushed. y=z1 qv1+z2 qv2 (k1/k2) +.............zn qvn (k1/kn) (3) F or particle sizes greater than k1 7 e. 6. x = k3, the value of y will be given by k3 A y = z1 qv1 + z2bv2 + Z3uV3 + zn zn qvn (k3/kn)(4) Only when x is equal to k, will y equal 100. 'Thus, the total product from a comminution operation will be a straight line on a log-log plot strictly up to a particle size equal to kl and above that size the line will curve so that y will equal 100 for the coarsest particle or k, (see Fig. 1). The actual shape of the size of distribution curve will depend upon the relative number of conmninution events of different kinds. In the case of ball milling, the ratio kn/kl may be pite large and there will be considerable deviation at the coarse sizes in a Schuhmann plot. kIowever, the grinding action in a rod mill is such that fine particles are protected from the rods by the coarse particles. Consequently, kn/kl will be quite small and the product from a rod mill will give a straight line Schuhmann plot almost to y equal 100%. In his paper, Dr. Schuhmann also has presented a very straightforward definition of grindability derived from the basic energy equation E = Ak-a (5) where E is the energy required to comminute a material to a size modulus of k and A is a constant. According to Dr. Schuhmann, the grindability of a material is the volume of material comminuted finer than unit size per unit of energy expended, this being 1/A. For comparison of grindabilities at any size two numbers are required, both = and 1/A, and anyone tabulating grindabilities should give both of these numbers. Concerning the experimental determination of grindabilities, if the material being comminuted possesses distinct cleavage, the energy re quired for comminution is given by E = Ak-(a-y) (6) where y is small number less than = . Because of cleavage, less energy will be required for comminution. To be certain that cleavage does not affect the gindability of the material being tested, it is suggested that the method used by Dr. Charles for determining grindability be used to ascertain if the deviation exponent y is zero or finite. R. Schuhmann, Jr. (Author's Reply) Dr. Fuerstenau's interesting comparison of rod milling and ball milling

Jan 1, 1961

By Pol Duwez

The effect of the rate of cooling on titanium, zirconium, and thallium has been measured. For titanium-molybdenum alloys, it has been shown that for molybdenum concentration up to 8 pct the rate of cooling has no effect on the transformation temperature, but this temperature decreases progressively with increasing molybdenum content. HIGH strength to weight ratio and remarkable corrosion resistance have often been advanced as the main reasons for the present widespread interest in titanium. For the physical metallurgist, the existence of an allotropic transformation in titanium is another important factor. As in the case of iron, an allotropic transformation may be the fundamental property upon which the response of Ti-base alloys to heat treatment will depend. It is therefore important to study the mechanism of the allotropic transformation in pure titanium and the effect of alloying elements on this transformation. The existence of an allotropic transformation in titanium was reported in 1931 by Schulze.' Later, De Boer et al.' determined the transformation temperature from a discontinuity in the electrical resistivity at 882"42O°C. According to recent work," the transformation temperature is 882.5"&1°C. The crystal structure of the room temperature a phase is hexagonal close-packed and the high temperature fi phase is body-centered cubic.' It is well known that the high temperature /3 phase of pure titanium cannot be retained by quenching to room temperature. Several investigators'-' have shown that in alloys of titanium with metals which are soluble in the @ phase (for example, nickel, molybdenum, chromium, or manganese), the /3 structure can be retained, providing the concentration of the alloying element is greater than a certain critical value. Below this critical value, the alloys transform during quenching, at least partially, into a supersaturated solid solution having the a. structure. This behavior is very similar to that found in some iron binary alloys (Fe-Ni and Fe-Mh, for example) and is an indication that the transformation might occur by means of a shear mechanism analogous to that observed in the austenite-martensite reaction. The present investigation is mostly concerned with the effect of the rate of cooling on the /3 to a transformation. In the first portion of this paper, the results obtained on pure titanium are described. Two other pure metals, zirconium and thallium, were also investigated, because they both have an allotropic transformation like titanium, from an hexagonal close-packed to a body-centered cubic structure. For purposes of comparison, the effect of rate of cooling of the y to a transformation of iron was included in the experimental program. The second part of this paper deals with Ti-Mo alloys. The equilibrium phase boundaries involving the solid state reactions on the Ti-rich side of the system were determined and a study was made of the effect of the rate of cooling on the transformation of the high temperature /3 solid solution. Experimental Procedure Since the main object of the present investigation was the determination of the effect of the rate of cooling on a transformation temperature, the best technique available was that used by Greninger" in his study of the martensite arrest in carbon steels. This method consists of heating a very small sample of metal to which fine thermocouple wires are .attached, cooling the sample rapidly by means of a blast of helium, and recording the temperature vs. time curve on an oscillograph. The apparatus used in the present experiments was very similar to that described by Greninger, except that the heating coil was made of molybdenum wire (0.040 in. in diam) and the assembly was placed in a bell jar under vacuum of 10" mm Hg or less. The specimen con-

Jan 1, 1952

By Robert E. Green, Kenneth Reifsnider

A microscopic X-ray diffraction technique was employed for the simultaneous study of the behavior of several families of lattice planes, whose local orientatiotz changes are manufestations of internal distortions resulting from specimen deformation. Photographs taken using aluminum were single crystals 1/64 in. In diam are presented which illustrate the appearance of various types of deformation- or growth- induced structural variations. Slip and lattice bending were detected in tensile tests for strains as small as 0.1 pct. Evidence of deformation bands, lineage structure, and void formation wns also shown. AmONG the most important methods of studying internal stresses in metals is the utilization of various X-ray techniques. The general subject of X-ray metallography has been treated in a most excellent manner by Taylor,1 and the use of X-rays for the direct observation of imperfections in crystals has recently been reviewed in an article by Newkirk2 and in the book edited by Newkirk and Wernick.3 Since the inception of metallographic X-ray analysis, there have been numerous technological developments and refinements, each with its particular advantages and disadvantages and, acrording to these, its particular applications. X-ray diffraction techniques can be divided into two general categories, that of X-ray diffraction microscopy and that of X-ray diffraction macroscopy. In the former are included such methods as those of Berg-Barrett, Lang, and Schultz2,3 which are concerned with microscopic imperfections such as dislocations. The second category includes all work concerned with the study of the condition of a crystal lattice structure as indicated by the marroscopic detail in its diffraction patterns. An example of this is the study of the diffraction manifestations of inhomogeneous plastic deformation as manifested by formation of deformation bands and inhomogeneous lattice rotations. The method used in the present investigation was an X-ray diffraction macroscopy technique. The geometry and analytical aspects of the method were similar to those of Julien and Cullity.4,5 The source was collimated with a single slit in a manner simi- lar to the "parallel beam'' method of Barth and Hosemann6 except that a continuous spectrum of radiation was employed. The apparatus produced large-beam transmission Laue patterns of thin cylindrical aluminum-wire crystals, which were deformed either in tension or torsion. Although the conventional X-ray target and interposed slit were not capable of the high resolution obtainable with a fine-focus X-ray source as employed in a microfocus apparatus, resolution was a secondary consideration in our technique, and was sacrificed to obtain sufficient intensity along a sizable length of the specimen. By using a grid indexing technique similar to that of Barth,7 we were able to study several diffraction lines from various planes simultaneously. The results of these tests give additional information with regard to the inhomogeneous deformation of single crystals, and the indexing procedure used provides a correlation between portions of the test specimen and portions of a diffracted beam. EXPERIMENTAL TECHNIQUE The experimental arrangement used is shown schematically in Fig. 1. A source of continuous X radiation from a vertically mounted Machlett X-ray tube possessing a copper target and operated at 20 kv and 10 ma was passed down a horizontal lead tube 80 cm long which terminated in an adjustable vertical brass slit. The slit opening was adjusted to correspond with the diameter of the test specimen. In front of the brass slit it was possible to place a screen wire mesh, one horizontal strand of which was a lead wire which served as a fiduciary mark, the screen itself serving as an indexing system as will be described later. Behind the screen was the test specimen which consisted of an aluminum single crystal wire 1/64 in. in diameter and 3 in. long. These 3-in.-long crystals were cut from

Jan 1, 1965

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.' Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors' laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By T. J. Neil, C. B. Manula, O&apos

This paper describes a simulation model developed to analyze truck haulage problems as they are found in the open pit mining and construction industries. The model, using a computer, cycles trucks between their assigned loading and discharge points over a measured haulage route. Required parameters for model operation include the number and type of operating trucks and loading units, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each origin. Equipment performance characteristics, system profile characteristics, and service time distributions are also included. Records are kept of all waiting times at the loading and discharge points and of any truck interference on the haulroads (moving queues), and a current journal of ore and waste production is maintained. In the pursuit of reduced truck haulage costs, management is confronted with three particular problems in truck and shovel mines. 1) What is the best assignment of trucks to shovels in the system? 2) If new equipment is needed, which new shovels and trucks will operate most effectively in the system? 3) Are any physical changes in the haulage layout warranted to increase productivity? For small open-pit mines the answers to these questions may be obvious. However, for larger operations complex problems are encountered with production and system configuration relationships usually being unknown. The mining simulator discussed here was developed to aid management in evaluating alternative pit-haulage schemes to reduce the risk involved in the selection and assignment of equipment in open-pit truck and shovel mining systems. There are two fundamental differences between this model and other truck haulage simulators: one is a difference of degree, the other a difference of kind. This model can simulate more complex systems than previous models by allowing transportation of material from multiple mine faces to multiple mine destinations and by being readily adaptable to a wide variety of mine layouts. The second difference that characterizes the model is the standard simulation of truck movements. This technique enables each vehicle to perform according to its mechanical capabilities and the physical profile of the haul road. Among the similarities between other truck haulage simulators and this model are the recognition of the probabilistic nature of certain service times in the system and the use of a digital computer to operate the model. The computer inherits the staggering computational and bookkeeping work loads and provides a means for compressing the time scale by allowing several days' operations to be simulated in a matter of minutes. DISTRIBUTION SYSTEM Basic aspects of the system analyzed here may be brought into focus by referring to Fig. 1, a schematic of the typical open pit truck-shovel operation programmed into the simulation model. A single stage materials handling scheme is employed to transport both ore and waste. Loaded trucks are directed to a crusher or stockpile if ore is being mined, while overburden is conveyed to a waste dump. Each shovel has a given number of assigned trucks and has two associated haulage routes, one for waste and one for ore. Up to 5 shovels and as many as 10 trucks per shovel (or a total of 50 trucks) can be operated in the model. Essentially the model, using a computer, cycles trucks between their assigned shovels and the proper discharge points over measured haulage routes. Required input parameters for model operation include the number of shifts to be simulated, operating time per shift, number and type of operating trucks and shovels, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each shovel. Equipment performance characteristics, system profile characteristics, and service time distributions are

Jan 1, 1968

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. [ ] Development of the new units was prompted by a desire for solution of the following problems: 1-The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pet of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be provided in the event that air lines were no longer available. 2-Drill performance has increased beyond the capacity of present 3 ½ -in. drifter machines. 3-The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4-Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5-Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6-In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1-It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1952