Search Documents

By Robert E. Green, T. Hinton

Expressions are derived for tke orientation factors appearing in the Grana to -Lucke theory of dislocation damping, for fcc crystals. The factors are given as functions of the elastic constants, the direction cosines of the specimen axis, atld the direction cosines of the particle displacemeizts, for darnping due to dislocation motion on each of the twelve possible slip systems as ixell as lor simultaneous dislocation rnotion on all twelve systems. RECENTLY Green' has outlined the general procedure for calculation of the modes of wave propagation in a single crystal possessing a given crystallo-graphic orientation. In addition he has suggested how the results of such calculations along with calculations of the resolved shear-stress factors for slip enable the orientation-dependent factors (orientation factors) appearing in the Granato-Lucke theory of dislocation damping to be calculated. However, reen' assumed that the maximum stress on dislocations was in the direction of the particle displacement of the elastic wave giving rise to the dislocation damping. The present cal'culations show that this is an oversimplified approach appropriate only to special cases of high crystallographic symmetry. The exact calculation of stress on the dislocations can only be obtained by resolving the nine components of stress associated with the elastic wave into the appropriate slip direction and then summing. In this paper the general expressions for orientation factors are derived for fcc crystals in terms of the elastic constants, the direction cosines of the particle displacements, and the direction cosines of the specimen axis, bearing in mind the point mentioned above. Equations are presented which give the orientation factors for damping due to dislocation motion on each of the twelve possible slip systems as well as for simultaneous dislocation motion on all twelve systems arising from elastic-wave propagation. These orientation factors are appropriate to attenuation measurements made by the pulse-echo technique, where the elastic wave is a traveling wave. They will be compared with those for the case of a standing wave as derived by Granato and Lucke which are appropriate to measurements of internal friction by the resonance technique. The expressions for the orientation factors are compared with the five values given by insruch,' based on unpublished work of Granato and Liicke, for positions of highest symmetry in the stereographic triangle. The various equations derived for modes of wave propagation and orientation factors have been evaluated for the case of aluminum crystals at 1-deg intervals throughout the stereographic triangle. These results will be presented in the form of contour diagrams in a subsequent paper3 and their relevance to ultrasonic measurements discussed. ORIENTATION FACTORS The coordinate system used for the calculations is shown in Fig. 1 and all specimen axes are taken to lie in the shaded standard triangle. The twelve slip systems are indexed according to Table I. Following the suggestion of lers, we may define the orientation factor Ok in the Granato-Liicke theory5 by the equation

Jan 1, 1967

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By O. D. Sherby

In 1938, Kanter' revealed that the steady-state creep rate of low-carbon iron alloys could be correlated by an activation energy expression, where the activation energy for creep, Qc, was found equal to about 90.0 kcal per mole for most of the alloys investigated. He suggested that creep at high temperatures might be controlled by some sort of solid self-diffusion process since the value of Qc was about equal to the known value for self-diffusion, Qd. Correlations were not further attempted along these lines until many years later, when new evidence2-8 was presented suggesting that Qc = Qd for many metals. This equality now appears to be established for ten metals (Al, Pb, Ni, Mg, Cd, In, a Fe, y Fe, Cu, and Au). This experimental fact prompted several investigators to postulate various mechanisms of dislocation motion which would yield an activation energy for creep equal to that for self-diffusion.7-9 Possibly the most accepted theory is that based on dislocation climb7 where a dislocation is envisioned to surmount a barrier by an atom-vacancy exchange process, thereby "climbing" from one slip plane to another. Such a model would suggest that the steady-state creep rate, i, should be directly proportional to the rate of self-diffusion, D, for a given creep stress. In order to more clearly reveal the relationship between creep and diffusion, and to eventually determine the correct model, it would be desirable to obtain data showing correlations between i and D, rather than with a comparison of the temperature coefficients, Q. It has been known for some time that the self-diffusivity of iron atoms is greatly decreased when body-centered-cubic (a) iron transforms to face-centered-cubic (y) iron. This has been ascribed to the more close-packed structure of y iron. The diffusivity ratio at the transition temperature is Da/Dy =350. Correlations of creep data for a and y iron5 reveal that the creep rates under a given stress at the transition temperature differ by about the same ratio (ea/ey 2 200). It would be difficult to reconcile these results on any other basis than that the diffusivity of atoms probably controls creep of iron in some very direct way. No other published data on other allotropic metals appear currently available for further checking such a possible correlation between i and D. Thallium transforms from a hexagonal close-packed (a) structure to a body-centered-cubic (ß) structure at 230°C (503°K) and the self-diffusivities of the two structures have been determined by shirn.10 His results are plotted in Fig. 1 where it will be noted that Dß/Da = 25 at the transition temperature. It would appear desirable, therefore, to determine the creep rates of polycrystalline a and ß thallium at the transition temperature, as well as determine

Jan 1, 1959

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By E. Clarence Peterson, Rip V. Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation reagents, it was found necessary to revert to the original oil reagents and their combinations with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar derivatives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidization is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter. TAILINGS These tailings were produced in the old Ophir Hill gravity concentrator previous to 1921. The original mill ore was a heavy lead-zinc-copper-silver-iron sulphide ore formed by limestone replacement. The gangue is a highly siliceous lime. An assay of the original milling ore would approximate 1.0 per cent Cu, 6 to 8 per cent Pb, 6 to 8 per cent Zn, 8 to 12 oz. Ag, 18 to 25 per cent Fe, 2.0 per cent CaO, 20 to 5o per cent insoluble. The gold content was 0.005 oz. or less. Tailing was impounded in a fairly wide area in a canyon about ½ mile below the mill. A number of dirt embankments were thrown up to form settling ponds and the tailing was allowed to flow through them in series. Coarser sand deposited at the upper end of the ponds and the finer slimes settled gradually as they passed through the successive settling ponds. As soon as the coarser tailings filled a pond, the tailings were by-passed to the next pond and teams and scrapers were used to haul the deposited sand onto the banks to make them higher. The final dump was approximately 2500 ft. long and 250 ft. wide at the bottoms, with banks sloping up at 45°. The coarser sands predominated at the upper ends and sides of the ponds while the proportion of slimes increased steadily at the lower ends. The lower end of the pond contained over 50,000 tons of slime tailings, 90 per cent of which passed through a 200mesh screen. SAMPLING The entire tailings deposit was sampled by drilling vertical holes so placed as to give data concerning size segregation and the contour of the underlying ground as well as to secure an assay sample. Different types of auger and post-hole drills were tried. None was found satisfactory because the stratified layers of

Jan 1, 1940

By David W. James

DURING a recent investigation of the transition from a planar to a nonplanar solid/liquid interface for the systems H20-NH4F and 0-AIR,' an apparatus was developed which enabled the morphology of the ice-water interface to be examined during the transition. The slightly curved interface was viewed at a glancing angle with a Bausch and Lomb X30 stereomicro-scope. The interface was obliquely illuminated by a polarized light source. It was thus possible to differentiate between small projections or depressions at the interface, both by a shadowing effect and by the way in which they distorted the colored interference fringes across a particular crystal surface. Many attempts were made to photograph the various stages of interface breakdown. Unfortunately, the limited depth of focus of the microscope rendered the system unsuitable for photographic recording. Visual examination, however, was facilitated by continuous adjustment of the microscope focus control. The following observations of the interface transition were recorded for dilute solutions of ammonium fluoride in water. They are compared with iller's postulated morphologies shown in Fig. 1. i) The initial departure from planarity was characterized by the appearance of a large number of small depressions or "pores" in the interface. ii) The pores were arranged in wavy rows all lying roughly in the same direction within a particular grain. iii) The pores did not appear to form near to grain boundaries. iv) The pores appeared in certain grains before others. v) The transition from the pore structure to the elongated cell structure, Fig. l(d), was difficult to follow. It occurred quite rapidly and no truly irregular cell structure, Fig. l(c), was noticed. vi) The elongated cells gradually became more uniform in size and shape, with straight cell boundaries. They remained elongated, however, and no regular hexagonal cells were observed, cf. Fig. l(e). Several conclusions may be drawn from these observations. Firstly, the appearance of a poxed or, more accurately, a pore structure can be used as a criterion for the onset of constitutional supercooling. Care should, of course, be taken to distinguish between the true pore structure and artifacts caused by splashed-back liquid, particles of oxide, or inefficient decantation of liquid retained between cell boundaries, as described by Spittle et al? Secondly, and contrary to the suggestions of Tiller el l., it seems that interfacial perturbations are characterized not by curved projections but by small depressions or pores. A recent independent investigation by Biloni, Bolling, and cole5 reported in this issue indicates that the depressions might be explained in terms of dislocations intersecting the solid/liquid interface. It is possible that the dislocation concentration is reduced in the vicinity of grain boundaries. This would then explain the grain boundary depleted areas noted in (iii) above. This work was partially supported by the Air Force Office of Scientific Research, Contract No. AF 49-(638)-1029.

Jan 1, 1967

By Walter R. Hibbard, Harold Margolin

DURING preliminary tests on the aging of a Cu-plus 5 pct Ag alloy,' a specimen which had been overaged 24 hr at 550°C was annealed in a nitrogen-hydrogen atmosphere first for 2 hr and then for an additional 28 hr at 600°C. After each anneal the specimen was cooled to room temperature in about ½ hr and X-ray photograms were made. The first film, Fig. la, revealed two sets of copper-base lines, one intense and corresponding to the parameter at 550°C, the other fainter and shifted away from the beam, corresponding to the larger parameter at 600°C (see arrows). The 30-hr film, Fig. lb, revealed the same two sets of copper-base lines with a reversal of intensity. In neither case do the copper lines form a broad band which would be indicative of a range of compositions. This phenomenon is thus a "discontinuous" type of solution. A similar phenomenon was observed in a Ag-rich Cu-Ag alloy.' Finlay and Hibbard9 have suggested that directional rather than random solution of precipitate occurs in some alloys. Conceivably, for Cu-Ag alloys, the matrix-transition-precipitate precipitation sequence is reversible for the re-solution of the precipitate caused by rapidly raising the annealing temperature of an overaged specimen. A copper-base transition structure supersaturated with solute might be formed around the precipitate as it dissolves, thus obviating the necessity for a gradually changing solute composition of the matrix. The solute atoms then might be transferred rapidly and locally from the transition to the matrix phase in the proper amount and at the proper location to obtain directly the new ex- panded solid solution. The theory implies a minimum of diEusion of solute in the matrix (i.e., no significant range of matrix composition) and possibly suggests that the composition of the transition structure will vary with the conditions of re-solution. A transition copper phase found in aged Cu-Ag alloys1 might fulfill this function. Evidence regarding this suggestion could be obtained in Cu-Ag alloys by overaging a specimen until no trace of the expanded copper lattice is present and then subjecting the specimen to a retrogression treatment. Re-appearance of the transition copper phase would confirm the theory. Additional details could be secured by varying both aging and retrogression temperatures. References 'H. Margolin and W. R. Hibbard, Jr.: Effect of Ternary Additions on the Age Hardening of a Copper-Silver Alloy. Trans. AIME (1951) 191, p. 174; Journal of Metals (Feb. 1951) TP 3002E. 2 W. Ageew, M. Hansen, and G. Sachs: Decomposition and Changes in Properties of Super-saturated Silver-Copper Alloys. Ztsch. Physik (1930) 66, p. 350. 3W. L. Finlay and W. R. Hibbard, Jr.: Some Effects of Applied Stresses on Precipitation Phenomena. Trans. AIME (1949) 180, p. 255; Metals Technology (Sept.

Jan 1, 1952

By Ronald J. Roman

Research pertaining to flow of solutions in leach dumps has generally been neglected. This technical note proposes a method for evaluating the flow patterns and incorporating the results into dump-leaching models. Three dump-leaching models1-3 have been proposed to scale up laboratory test data to expected field results. These models are based on the same physical picture in a dump and differ only in the importance of diffusion or surface chemical reaction rate. Selection of this rate-controlling phenomemon is based on type of ore (sulfide or oxide), physical dimensions of the particles being leached, and the leach heap itself. All three models are applicable to specific types of operations. The models are similar in the use of a size distribution analysis for the dump material and the assumption that the leach solution flows around each particle. Transport of the leaching agent to the interior of the particle takes place by diffusion [(Fig. 1)]. However, normal dumps are of a higher bulk density than the material in a laboratory column used to generate the scale up data. How does this difference in bulk density affect the scale up equations? Increasing the bulk density can be expected to give more particle-to-particle contact; therefore, individual particles will be blinded by each other. As blinding increases with bulk density increase, the particles will behave like larger particles with a coarser apparent size distribution. The extreme will occur when the bulk density reaches that of the undisturbed rock, the entire dump behaving as a single particle with the dimensions of the heap itself. Harris4 alluded to this phenomenon in his paper. An alternative method of describing the same phenomemon is to consider the flow paths of the solution. At high bulk densities leach solution no longer surrounds each particle, but flow paths are separated by several particles and channeling is said to take place. Instead of the particle radius being the maximum distance through which the leaching agent must diffuse, the maximum distance is half the separation distance of the solution flow path. Particle size distribution must then be replaced in the models by the concept of channel separation distribution. Like size distribution, channel separation distribution specifies the cumulative percentage of the rock in the dump situated less than a specified distance from a solution channel. Thus, [ ] Distribution of the solution channels is a function of how the dump was built (among other things), and therefore it cannot be determined in the laboratory. Accordingly, it becomes necessary to determine a range for d and a in existing operations or measuring these parameters before leaching starts. Howard5 gives a clue to one possible technique of measuring solution channel distributions. When his paper was published little was known about the phenomemon of leaching; the importance of this type of data was not recognized. [Fig. 2] is a Y-Y log for one hole drilled

Jan 1, 1978

By Harry Udin

IN 1948, the writer and his associates determined the surface tension of solid copper by balancing the force of surface tension in a very fine wire against an external load.' At that time we, in common with other early workers, assumed that grain boundary energy in a pure metal is very small in comparison to the energy of an external surface. Accordingly, we neglected the internal surface energy of the coarse-grained specimens. Since that time, experimental evidence has accumulated showing that grain boundary energy, far from being small, is generally about one-third of the energy of an external surface.2-4 This is sufficient to introduce a significant error into our determination. The differential equation governing equilibrium is: wdl - yds, + y*ds2 [I] rather than wdl = yds as originally written. w is the balancing force in dynes, 1 the length of the specimen, sl the external and s2, the internal surface area, y the copper/ copper vapor surface tension, and y* the grain boundary tension. Fortunately, we had made for another purpose a careful study of the size and shape of the grains, and found that the boundaries, with rare exceptions, traversed the specimens and were perpendicular to the wire axis. For this case, eq 1 leads to w = rry -(n) r2y* [2] where r is the wire radius and (n is the number of grains per unit length. A count of some twenty 5-mil wires indicated that - n became 80 & 10 after a short anneal near the melting point, and remained nearly constant for as long as 96 hr at temperature. An assumption of y* = 1/3y leads to a defining eauation for r: [31 The term in the brackets may be considered a correction factor applied to eq 11 of ref. 1. Upon applying this factor, the surface tension of solid copper at its melting point is found to be 1650 & 100 dynes per cm, rather than 1370 as previously reported.' The new temperature coefficient is —0.55 dynes per cm per "C. Grain boundary energy is more significant than surface energy to the physical metallurgist. It is evident from eq 2 that a series of experiments with wires of different grain size can lead to an evaluation of y*. The details of such an experiment are being worked out now. References 1 H. Udin, A. J. Shaler, and J. Wulff: The Surface Tension of Solid Copper. Trans. AIME, 185, 186-190; Journal of Metals (Feb. 1949) TP 25303. 2 G. L. C. Bailey and H. C. Watkins: Surface Energies in the System Solid Copper-Molten Lead. Proceedings Physical Society. (London) (1950) 36B, 350. 3 L. H. VanVlack: Inter granular Energy of Iron and Some Iron Alloys. Ph.D. Dissertation, Univ. of Chicago, Sept. 1950. 4 . P. Greenough: Grain Boundary Energies in Silver. R.A.E. Report, No. Met. 52. (May 1950) Fan-borough, Hants, England.

Jan 1, 1952

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Ronald C. Koo

SMALL additions of potassium, aluminum, and silicon as oxides (referred to as dope) to tungsten have been known for several decades to have a very large effect in raising the recrystallization temperature and altering the recrystallized grain morphology of heavily drawn wire. Previous investigations of this doping effect1 6 have led to various speculations but all failed to deduce unequivocally the physical state or the mechanistic influence of the dopant. Recently, walter7 has observed, by transmission electron microscopy, strings of "fine particles" in heavily rolled and annealed doped tungsten sheet and concluded that they were particles of mullite (Al6Si2013). His conclusion was inferred from the electron diffraction patterns of large particles ex-trated by carbon replication of fractured surfaces of slabs rolled from sintered ingots. That the strings of "fine particles" in heavily rolled and annealed sheet were also mullite was an assumption for which no evidence was presented. A similar investigation has been carried out in this laboratory over the past 2 years on a variety of tungsten wire: doped tungsten, and undoped tungsten, as well as 218 doped tungsten purchased from the Lamp Metals and Components Department of the G.E. Lamp Division. Although the electron microscope observations are similar to those reported by Walter, the writer has reached a different conclusion concerning the physical state of the dopant in annealed tungsten. The purpose of this communication is to present evidence that the strings of "fine particles" observed in transmission specimens are not mullite, but are voids. In the present investigation, tungsten wire, 0.88 mm in diam, was rolled into ribbon 0.2 mm by 125 µ thick. The ribbons were annealed in vacuo at a pressure of -1 x 10-5 Torr and then thinned electrolytically in a 2 pct KOH solution. Fig. 1 shows a typical transmissicjn electron micrograph of a sample annealed at 1700°C for 30 min which reveals rows of closely spaced voids having a light contrast (referred to as "fine particles" by Walter) aligned parallel to the working direction. Stereo micrographs (by D. Moon, Westinghouse Research and Development Center) have shown that these voids do not exist on the surfaces of the specimens as a result of thinning but are within the thin-foil specimens. The following experiments have been performed to verify that these are indeed voids. I) Effect of Annealing. Voids are absent in unannealed specimens and appear only after annealing. This behavior cannot be explained if they were solid particles such as mullite. Precipitation (in an unquenched specimen) upon annealing requires solute elements having decreasing solubilities with increasing temperature. Although the solubility of aluminum in tungsten does decrease with increasing temperature, precipitation requires a concentration in excess of 1.4 wt pct,8 which is at least two orders of magnitude higher than the aluminum content in doped tungsten. It is also unreasonable to assume that particles aligned in rows initially present in unannealed specimens were too

Jan 1, 1968

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By H. S. Cannon, F. N. Rhines

The application of a static load to a copper powder compact during sintering at an elevated temperature accelerates the rate of sintering in such a way that a given load induces the same proportional increase in rate for all times of sintering. It is shown that sintering under a load is like creep under a fixed load in that the stress required to accomplish a given degree of densification is proportional to the logarithm of the sintering time. VIRTUALLY all of the theories of sintering that have been put forward within recent years have contained the assumption that the chief driving force of the process is the surface tension resident in the exposed surfaces and internal pores of the compact, or powder mass. An externally applied load might be expected to provide a somewhat equivalent driving force for sintering. It is known that the application of a compressive load, during sintering, hastens densification, but it is by no means clear whether sintering under the influence of surface tension alone and sintering under an applied load are fundamentally similar processes. The present study was undertaken in an effort to obtain an answer to this question and with the hope that the answer may contribute to an understanding of the mechanism of sintering. It has been found that there is a close relationship between sintering and creep processes. Copper powder compacts were sintered in hydrogen at 1000 °C under dead loads of 0 to 165 psi and the progress of sintering was observed by means of density measurements. Using a commercial reduced oxide copper powder, see Table I, cylindrical compacts Yz in. x x in. high were made at a pressure of 12,500 psi. For sintering, these were placed in a cylindrical graphite container into which they fitted snugly. A compressive axial load was applied to the compact through a graphite rod of similar diameter, which rested upon the upper end face of the compact; iron weights, in suitable amount, were placed upon the graphite rod to provide the load. This assembly was encased in a vertical silica tube within a resistance-type furnace capable of maintaining a substantially constant temperature within the working zone. After various predetermined times at temperature, the samples were removed from the furnace and their density was measured by conventional means. The heating-up and cooling-down times have been included in the computed sintering time, using the assumption that the sintering rate doubles for each increase of 10 °C in temperature. The experimental results are presented in Table 11. Upon metallographic examination of the specimens, it was found that there was no apparent change in the shape of the pores as a result of loading, i.e, no flattening, Fig. 1. Substantial contraction away from the container walls was observed in all samples sintered with loads of 10.5 psi and less.

Jan 1, 1952

By G. C. Gardner

A new correlation of blast penetration in model and operating blast furnaces is presented which overcomes objections to prevzous correlations. It is shown that the tuyere diameter is only of small importance in determining the magnitude of the penetration. The data from operating furnaces correlate satisfactorily with the data from models whose cross section is a segment of a circle. A bubble-shaped gas space called a "raceway" normally exists in front of the nose of a blastfurnace tuyere. The periphery or "wall" of the raceway is well defined and is composed of densely packed charge particles. The blast. issuing as a jet from the tuyere, entrains gas from the raceway, in the usual manner of a jet, as it flows to the opposing wall. There it divides and flows back around the walls to be entrained once more. The blast must, of course, eventually leave the raceway and pass up through the charge column, but before it does it may, on the average, make several circuits of the kind described and in doing so it carries with it charge particles, which, because of their fast and circulating motion, suggested the name of "raceway". A fuller description of the raceway may be found elsewhere."' Here it is only necessary to mention, in addition, the measurement which characterizes its size. If an iron bar is pushed through the opened peepsight of a tuyere, .as far as it will go with ease, it will be stopped by the relatively impenetrable opposing raceway wall arid the distance that the bar has been pushed from the tuyere nose is called the "penetration". This measurement may be of practical importance and has; been the subject, with considerable success, of several attempts at correlation with other variables2-5 as stated in the next section. There is still, however, a serious objection to the most recent correlation,3 which is overcome by the correlation proposed in this paper. It will be shown that the objection is not trivial, in that the new correlation will attribute considerably different importance to the variables affecting the magnitude of the penetration. The data to be treated were made available by Wagstaff and are the same as those used in his correlation. They include measurements taken on small models, in which a cold air blast was used and no combustion occurred, and they also include data from operating blast furnaces at Wheeling and Fairless. The information from the blast furnaces will be shown to be in substantial agreement with those models whose plan views are segments of a circle and which are thus like segments of a blast furnace. First, Wagstaff's most recent correlation3 will be discussed and the objection will be given. Then the new correlation will be developed and its implications considered. CORRELATION OF J. B. WAGSTAFF Wagstaff's correlation is where and D — the penetration D,-the internal tuyere diameter V —the blast velocity in the tuyere

Jan 1, 1961

By S. D. Michaelson

[CONTENTS PACE See TP 2377, Min. Tech, May 1948 for discussion of A Technique for Photographing Difficult Subjects through a Petrographic Microscope (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL). Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy (TP 2141 by R. A. ....... PALLANCH, Min. Tech:, March 1947. Discussion by S. D. MICHAELSON). I Symposium on Milling Devices and Practices. (TP 2162 by J. F. MYERS and R. J. TOWER, Min. Tech., May 1947. Discussion by HARLOWE HARDINGE). ............ 2 Rod Milling-Plant and Laboratory Data. (TP 2175 by J. F. MYERS, S. D. MICHAELSON and F. C. BOND, Min. Tech., July 1947. Authors' supplement and discussion by HARLOWE .......................... HARDINGE, and B. H. IRWIN) 2 A New Separating Vessel for Sink-float Concentration. (TP 2182 by E. C. BITZER, Min. Tech., May 1947. Discussion by E. H. CRABTREE, JR.) .................. 5] Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy S. D, MICHAELSON*-The method of determining the efficacy of a separation described in this paper, gives the metallurgist a most useful guide for keeping his ship on an even keel When the ore Waves vary from placid seas to high breakers. Now that such a method of evaluating metallurgical efficiency has been developed and proven practical, it Would seem logical to introduce the next, and more final, factor of Economic Efficiency. I choose to define this term as the percentage ratio of net return from milling to the theoretical maximum net return. The actual operating cost subtracted from the actual mill return represents the net actual amount received for the material treated. Experienced operators of most plants Would ordinarily have enough data on hand to estimate a theoretical milling cost per ton, based on labor, power, supplies and maintenance When operating at maximum tonnage With minimum trouble and under ideal ore conditions. When this theoretical estimated cost is subtracted from the theoretical maximum ore return (calculated by Pallanch's method) the resulting figure is the maximum theoretical net amount the mill operator could hope to realize in processing the ore. The percentage ratio of these sums, of actual to theoretical, is the economic efficiency of the operations. This economic efficiency, if determined on the basis of a fixed market price for metal and similarly fixed base rates for labor, power and supplies, Will reflect the effect of changes in milling practice, labor efficiency and equipment condition. When computations made on the basis of actual current rates for labor, power and supplies are compared With similar actual figures for past periods they will show forcefully how energetic our hunt must be to develop man saving controls, more effective metallurgy, and better equipment to maintain profitable operations. Such computations also offer a simple means of determining how much more labor, supplies and power can be put into the mill operation to obtain an increase in metallurgical recovery at a profit.

Jan 1, 1947

Abbott, Argyle Campbell 1209 Sherwin Ave., Chicago, Ill. Almstrom, Adne A., Student, Met. Engrg., Washington State College Pullman, Wash. Ankudinoff, N., School of Mines, Univ. of Utah Salt Lake Cite, Utah. Apter, Robert F., Student, McGill Univ Montreal, Que., Canada. Bailey, Donald G 798 Kensington Rd., Los Angeles, Cal. Baker, Kenneth B., Met., Aluminum Co. of America Pittsburgh, Pa. Barger, Thomas, Student, Univ. of North Dakota Grand Forks, N. D. Bartholomees, Geo. C Box 304, Bonne Terre, Mo. Bates, Walter, Student, Univ. of Utah, School of Mines Salt Lake Cite, Utah. Bobb, Russell V 16 College Ave., Houghton, Mich. Boswell, John C., Stripping Asst., Fairbanks Exploration Co Fairbanks, Alaska. Brandenburg, E. C., Student, Univ. of Kentucky 112 Church St., Lexington, Ky. Brannen, John, Chemist, Assay Office, Consolidated Min. & Smelt. Co. of Canada, Ltd., Tadanac, B. C., Canada. Brooker, Edgar, Jr., Student, Ferrous Met., Stanford Univ., Stanford University, Cal. Brooking, Leslie E 738 Lakoma, Norman, Okla. Clark, Martin Lester, Student, Missouri School of Mines Rolla, Mo. Collins, Edward D., Jr Box 1597, Ribbing, Minn. Comeau, Faye Bernard, Student, New Mexico State School of Mines Socorro, N. M. Conder, Henry S., Student, Pet. Engrg., College of Min., Univ. of California, Berkeley, Cal. Cotton, John Francis, Metallographist, Stealton Plant, Bethlehem Steel Corp., Steelton. Pa. Dahlgren, Elmer George, Student, Univ. of Wisconsin, Tripp Hall, Madison, Wis. Dale, James L., Student, Colorado School of Mines Golden, Colo. Dashti, Mirza Abdullah Khan, Graduate Student, Columbia School of Mines, Engrg. Chemistry, New York, N. Y. DeHuff, Gilbert L., Jr., Student, Lehigh Univ Bethlehem, Pa. de Romana, Enrique P., Jr. Engr Casilla 22, Arequipa, Peru. Oresbach, Charles Howard, Geol., Gulf Production Co Box 1428, Amarillo, Tex. Evens, Howard G., Student, Michigan College of Min. & Tech Houghton. Mich. Fassler, Glen Emerson Rodman, Inspiration, Ariz. Feight, Charles Donald, Foreman, Clairton By-Product Coke Wks., Carnegie Steel Co., 319 5th St., Wilson, Pa. Floe, Carl F., Student, State College of Washington Pullman, Wash. Fuentes, Vicente, Student, Pet. Engrg., Univ. of Oklahoma, School of Mines, Norman, Okla. Fuhrman, Carl F., Student, New Mexico School of Mines Socorro, N. M. Goergen, Gerald G., Cerro de Pasco Copper Corp Casapalca, Peru. Grove, Hubert A., Training Course, U. S. Aluminum Co New Kensington, Pa. Gastetter, Robert E 1010 N. Cherry Ave., Tucson, Ariz. Halbouty, M. T., Student, Texas Agriculturcl & Mech. College, Box 254, Faculty Exchange, College Station, Tex. Halfast, Edgar 710 E. Okmulgee Ave., Muskogee, Okla. Hall, Robert Lee 121 58th St., Niagara Falls, N. Y. Hanson, Rolf H., Student, Colorado School of Mines Golden, Colo. Hillyer. Shaler G., Student, New Mexico School of Mines Socorro, N. M. Hoertel, Frederick W., Met., R. W. Hunt Co., Engrs St. Louis, Mo. Holtz, Henry G., Student, Ohio State Univ Columbus, Ohio. Hon, Richard J Box 721, Miami, Ariz. Huffman, James O'Neil, Student, College of Min., Univ. of California Berkeley, Cal.

Jan 1, 1929