Search Documents

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors' reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

C. H. GIBBS,* Salt Lake City, Utah (written discussion?).-The development of the coke industry in Utah had a somewhat checkered career for the first 50 years of its existence. About 1851 the iron-ore deposits of the Iron Springs and Iron Mountain mining districts, Iron County, Utah, were discovered. Obtaining of iron for any purpose at the time involved its shipment from the Mississippi River to Utah, by ox-team. The result was that the pioneers endeavored to establish an iron-ore smelting plant at what was known as Iron City, near Iron Mountain, in Iron County. Bishop Taylor, who headed this enterprise, endeavored to obtain coal suitable for coking from the Cretaceous coal measures immediately east of Cedar City. A few small bee-hive coke ovens were built and lump coal was coked in these ovens; or, more properly speaking, the volatile matter of the lump coal was driven off, leaving a carbonized material that retained the lump shape, although it was extremely, friable. This coke was promptly found to be unsuitable for iron smelting, not only clue to its extreme weakness under smelting load, but also because of the fact that it carried about 5 per cent. sulfur. Bishop Taylor made a very thorough and exhaustive effort, covering a considerable period of years, to locate suitable coking coal in Southwestern Utah. His efforts failed, and in 1902 the iron-ore property acquired by him and associates was sold to the Colorado Fuel and Iron Co. It is of interest to note in this connection that the iron-ore deposits of Iron County at present are the largest known undeveloped iron-ore fields on the North American continent. It is safe to say that there is at least one hundred million tons of 55-per cent. ore actually in sight. In 1878, coal-mining operations were begun at Connellsville, in Huntington Canyon, Emery County. Ten 8-ft. bee-hive ovens-were constructed, and lump coal was carbonized for use in the Salt Lake valley smelters. The product was somewhat better than that obtained in Iron County, but was still of very inferior quality. It had to be hauled a distance of 140 miles by wagon to the two small smelters then operating in Salt Lake valley. These ovens operated only a very short time. The next move toward obtaining a coking coal was in 1889 when the Pleasant Valley Coal Co. began operations in the Castle Gate district. In 1890, eighty 8-ft. bee-hive ovens were constructed, and the product. was used until 1900 in all the smelters in Utah. During this period, 124 additional. ovens were constructed, making a total of 204 bee-hive ovens operating at Castle Gate.

Jan 11, 1918

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By George Packard

THE shaft of the Raven. mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70° from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47°. This angle continues to the 1,100-ft. level, below which it, curves with a 125-ft. radius to 78°. In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging- and foot-walls, but presses strongly against the west, dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, and wall plates cut 6 in. deep y the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev.. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging-wall of the shaft the original bearing was simply a piece of 2 by 1-1 in. strap iron, 10 in. long, turned up at the end in a circle of 18 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot-wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 8, 1914

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By M. T. Worley

This paper reports investigative work conducted to develop a method of estimating the groundwater influx from a homogeneous permeable formation into a vertical mine shaft during sinking. A method of analysis was developed using data obtained from pumping tests and a modification of the Theis non-equilibrium interpretation technique. Excess influx of groundwater into mine shafts has long been one of the more important problems encountered in the development of a mining property. Much work has been done on methods of preventing such influx and on pumping schemes to control inflow if preventive measures fail. The fundamental aspects of the problem, on the other hand, seem to have been neglected. The purpose of this paper is to review the fundamentals of groundwater flow and to propose a rapid method of analyzing hydrologic data in order to estimate influx from a homogeneous permeable formation into a mine shaft. Such an estimate of the quantity of water to be encountered is of value in planning grouting, pumping and other programs designed to control that influx. It is emphasized that the proposed method of analysis should be regarded only as a tool to be used in evaluating the problem before investing the capital necessary to begin development of a property. FUNDAMENTALS OF GROUNDWATER FLOW In order to effectively approach the problem of estimating influx into a mine shaft, a knowledge of the fundamentals of fluid flow through a porous medium is necessary. Darcy, in 1856, developed an empirical relationship to explain the flow of water through sand filters. This relationship V = k (dh/dl), is the basis for all other flow formulae. It has been shown that Darcy's relation is a solution of the Laplace equation and thus is analagous to other natural phenomena such as heat flow. Theis, using the analogy of heat flow by conduction, developed an expression for determining the transient or time-dependent groundwater flow through a homogeneous, isotropic medium. The resulting equation Was also derived by Jacob using hydrologic considerations alone.' The individual terms in the equation are described in Table I. It is important to understand the assumptions upon which this equation is based. 1) The medium through which the fluid flows is infinite in areal extent, homogeneous and isotropic. 2) The well into which the fluid discharges completely penetrates the medium. 3) The characteristics of the medium remain constant at all times. 4) The initial pressure surface is horizontal. 5) The confining media are impervious and horizontal. 6) Fluid is removed from storage instantaneously by a decline in pressure. 7) The diameter of the discharge well is infinitesimal with respect to the drainage radius of the medium.

Jan 1, 1962

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

Samuel T. Wellman, Cleveland pioneer steel man, who was often referred to as the "father of the open-hearth process of the United States," died suddenly on July 11, 1919, of heart disease, at Stratton, Me. For more than half a century, he was closely identified with the improvement of equipment used in the making of steel and contributed a number of inventions that virtually revolutionized the industry. Mr. Wellman was born Feb. 5, 1847, at Wareham, Mass., his father at the time being superintendent of the Nashua Iron Co., Nashua, N. H. After attending public school and a year at Norwich University, he served in the Civil War as a corporal of the first New Hampshire Heavy Artillery. He went to Pittsburgh in 1867 and assisted in starting the first crucible steel melting furnace built in America at the works of Anderson, Cook & Co. It melted a ton of steel with an average of 1000 Ib. of nut coal, which cost less than $1, while the melting of a ton of steel in crucibles in the old fashioned coke furnace took three tons of the very best coke, costing from $2 to $3 per ton. This furnace was a great success and in a very few years had driven the coke furnace out of use. From Anderson, Cook & Co., Mr. Wellman went to the Singer, Nimick & Co. works, Pittsburgh, where he built two crucible steel melting furnaces of the same type. After that he spent some time in the office of the Siemens agents in Boston and also at steel works in different parts of the country, starting crucible steel furnaces. He then went to the Bay State Iron Works in South Boston, Mass., where he built the first open-hearth furnace that was a commercial success in the United States. It made steel of a much better quality than had previously been made in this country. The principal use to which it was put in those days was the manufacture of locomotive fire-boxes. From South Boston, he went hack to the old works in New Hampshire where his father was still superintendent, and built for it an open-hearth furnace, a plate mill, and a bar mill. In 1873, Mr. Wellman went to Cleveland to design and build the plant of the Otis Steel Co. He remained with this company for 16 years as engineer and superintendent. During this time he developed the open-hearth charging machine and introduced the electromagnet for handling pig iron and scrap steel. The first charging machine was operated by hydraulic power, and although it was not entirely satisfactory it performed the work fairly well and encouraged its inventor to build another one, which was driven by electric motors. This proved

Jan 1, 1920

By O. L. Culberson, J. J. McKetta

INTRODUCTION The equilibrium constants for methane and for water, and for ethane and water have been calculated from experimental data for the two binary systems.2,3,11,12 These constants are for the two-phase systems for the temperature range of 100" to 340°F and the pressure range of 200 to 10,000 psia. The constants for ethane are greater than those for methane. Equilibrium constants for a natural gas from a natural gas-water system6 are about the same as those for methane. Equilibrium constants for water in all three systems are very nearly the same over the greater part of the range of temperatures and pressures studied. In ideal solutions, the vapor-liquid equilibrium constants for a component should be the same in all such solutions at a given temperature and pressure.5 Few solutions are ideal, and consequently the use of generalized constants often leads to error in situations where they do not actually apply. In decidedly non-ideal systems, it is desirable to have equilibrium constant data for the specific system. Vaporization equilibrium constants may be calculated either by thermodynamic methods or from experimental vapor-liquid equilibrium data. In the thermodynamic calculation. the equilibrium constant K may be shown to be" K = fP,/fl'..........(1) where fPi is the fugacity of the pure component i at the given temperature and at the vapor pressure of the pure component, and fp is the fugacity of pure i in the gaseous state at the temperature and total pressure of the system. At best the thermodynamic calculation results in a K applicable to ideal solutions. Equilibrium constants calculated from Equation (1) have been found to have only limited agreement with experimental values, even though the solutions for which they were calculated approached ideality."'" If the more volatile component is at a temperature above its critical, the accuracy of the equilibrium constant for the component is made more doubtful by the use of the vapor pressure term under such conditions. In order to make the thermodynamic calculation on a component above its critical temperature, one must resort to one of the empirical methods of extrapolation of the vapor pressure to conditions above its critical point.13 Application of the thermodynamic equilibrium constant then to the methane-water or the ethane-water systems would be risky since the systems are non-ideal, and the methane and ethane are above their critical in most petroleum operations. ETHANE-WATER SYSTEM In the temperature range of from 100° to 340°F and for pressures up to 10,000 psia, the vapor-liquid equilibrium data 'References given at end of paper. Manuscript received in the office of the Petroleum Branch March 16, 1951.

Jan 1, 1951

By D. M. Davidson

The drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of IIO ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered and is drained by the Piney and Tye Rivers, which are tributary to the James. Geology The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 4.5° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelson-ite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more pronounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,' the TiO2 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. Sampling Methods and Procedure During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this pos sible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1949

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiCl-KCl mixtures, as first proposed by Guntz.2 The details of the industrial process have not been made public but Osborg8 stated that an efficiency of more than go pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of too kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, Si02, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units, such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, especially with respect to the iron and calcium content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1947

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949

By A. Kenneth Schellinger, O. Cutler Shepard

INTRODUCTION OVERGRINDING, or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncontrolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about 90 pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, overgrinding is detrimental to the flotation process. Overground slime coats larger particles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 Conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The remedy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. DEVELOPMENT OF APPARATUS AND EXPERIMENTAL METHOD Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7 ½ in. in diameter and 8 in. deep. A cast-iron disk was mounted on the end of a vertical shaft so that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffeemill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, weighed charges of ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned on so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1947

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951