Search Documents

By Louis V. Bender

AfteR investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled, is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds' time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 191/4 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting. After the run of three months, the roof was in excellent condition. At the back of the furnace the bricks were not cut into at all; at 30 ft.

Jan 1, 1915

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neilll observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in inter-granular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle3 in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1942

By Fred Wise, C. W. Wark

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By L. P. Teas

Although 1930 has been a year of stagnation, proration and curtailment, the Gulf Coast has measured up to its tradition in the matter of interesting and significant discoveries. Only 2 domes and 7 new structural areas were brought into the producing column in 1930, whereas, in 1929, 13 domes and one structure were added to this list, yet a total of 14 new producing horizons were proved on various domes and structures. On 5 domes new flanks were successfully tested for commercial production. The year 1930 has shown at Barber's Hill that oil in commercial quantities may exist below salt or cap. Numerous wells have been drilled through cap, or even salt itself, into good producing sands. The past year has been particularly notable in the interest and in the number of deep holes drilled. Two wells have gone below 8000 ft. in each of the states of Texas and Louisiana, and in the two states together 14 wells have gone below 7000 ft At the beginning of the year only one well was producing below 6000 ft. in coastal Texas, while at its end, 19 wells were producing or had produced. Geophysical discoveries and activity on the Coast have waned and this type of work has moved further inland. The peaks of production at Pettus, Barber's Hill, Raccoon Bend, Refugio, Orchard and at Humble, in Texas; and at Lake Barre, Port Barre, Black Bayou, White Castle and Vinton in Louisiana, were seen this year. These were new peaks for Humble and Vinton, of course, these fields having previously gone through periods of peak flank production. In Table 1 the completions listed are for the entire month of December in both years. It is remarkable that in 1930, a year of overproduction and proration, there were actually more wildcat operations at its end than at the end of 1929; but it is gratifying that the operations in the proven fields were exactly one-half what they had been at the end of 1929. The price of A grade coastal crude, or oil below 25" Bé., has been cut from $1.30 at the beginning of the year to $1.00 at its close; and B grade, or oil above 25o Bé., has been reduced from a price range of $1.15 to $1.63 down to a range of from $0.75 to $1.22. In spite of these reductions there has been no proration program on the Coast. Systematic

Jan 1, 1931

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Lawson P. Entwistle

One of the important reserves of mangani-ferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which has been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. Prom a noselike protuherance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (I) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale. Boston Hill comprises three rolling hills southwest of and adjoining the town of Silver City (pop. 5044), Grant County, N. Mex. The mining district covers less than 2 sq. miles. Silver City, on a branch line of the Atchison, Topeka, and Santa Fe Railway, is a supply point for the important mining communities at Santa Rita, Hurley, Hanover, Tyrone, and Mogollon. The Chloride Flat mining district adjoins Boston Hill on the north. History and Production Bonanza-type silver ores were discovered in the Chloride Flat mining district during the silver boom of the seventies and eighties, at which period it has been credited with as much as $5,000,000 production. In 1916 manganiferous iron ore was first shipped from the Boston Hill mining district to Pueblo, Colo., where it was mixed with manganese ore from Lead-ville and smelted into spiegeleisen. During 1926 and 1927 the Colorado Fuel and Iron Co. mined and churn-drilled part of the district. Mining operations ceased during the depression of the thirties, but production was resumed in 1937. Since 1916 the Boston Hill mining district has produced about 600,000 long tons of ore averaging about 12 per cent manganese and 35 to 40 per cent iron.

Jan 1, 1949

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

By Lawson P. Entwistle

One of the important reserves of mangani-ferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which has been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. Prom a noselike protuherance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (I) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale. Boston Hill comprises three rolling hills southwest of and adjoining the town of Silver City (pop. 5044), Grant County, N. Mex. The mining district covers less than 2 sq. miles. Silver City, on a branch line of the Atchison, Topeka, and Santa Fe Railway, is a supply point for the important mining communities at Santa Rita, Hurley, Hanover, Tyrone, and Mogollon. The Chloride Flat mining district adjoins Boston Hill on the north. History and Production Bonanza-type silver ores were discovered in the Chloride Flat mining district during the silver boom of the seventies and eighties, at which period it has been credited with as much as $5,000,000 production. In 1916 manganiferous iron ore was first shipped from the Boston Hill mining district to Pueblo, Colo., where it was mixed with manganese ore from Lead-ville and smelted into spiegeleisen. During 1926 and 1927 the Colorado Fuel and Iron Co. mined and churn-drilled part of the district. Mining operations ceased during the depression of the thirties, but production was resumed in 1937. Since 1916 the Boston Hill mining district has produced about 600,000 long tons of ore averaging about 12 per cent manganese and 35 to 40 per cent iron.

Jan 1, 1949

By C. E. Nelson

THE purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.* The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protec-

Jan 1, 1944

By G. A. Crowe, W. T. Bishop

WHILE the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,2 by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,3 cadmium,3.4 cobalt,4 copper,3-9 gold,10 iron,3,11 lead, 3,12,13 molybdenum," nickel,4.8,9 tin,15 and zinc3,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. PRINCIPLE OF THE METHOD The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1946

By Oswald J. Heinrich

THE responsibility resting upon the owners and managers of mines where fire-damp is generated, renders it a matter of imperative duty that a full and correct statement of any explosion that occurs should be given to the public. But such a statement must be based on the testimony of impartial eye-witnesses or trained experts. Then a sad experience may result in the adoption of effective preventive measures. In the absence of any official and professional body of mining experts in the State of Virginia, the writer desires to submit to his professional brethren of the American Institute of Mining Engineers an account of an explosion which recently took place in a colliery under his management, and earnestly desires a thorough and impartial discussion on the facts submitted. Description and Plan of the Mine.-The "Grove" shaft is situated at the nearest point 825 feet from the last old workings upon the Midlothian property, south of the old Pump shaft works. (See Plate III.) The shaft was sunk by the former company, some thirty years ago, to the depth of 622 feet. An incline over 230 feet long, starting in a northwest direction at a depth of 105 feet above the shaft bottom, had been driven to explore the coal on the dip. A return of very small dimensions had been driven round the shaft on the south side, entering the upcast chamber. With the information obtained from the former company that a seam of coal about four feet thick, at a depth of 490 feet, had been found, and with the information obtained by the present proprietor, R. T. Burrows, of Albion, N. Y., by means of two boreholes on the dip west of the old shaft, in both of which workable seams of coal at various depths had been ascertained, the clearing out and thorough retimbering of this shaft were commenced in March, 1873. Borehole No. 1, at a depth of 477 1/2 feet from surface, revealed a seam of coal. This borehole was afterwards carried to a depth of 1140 feet to the granite, without finding any other seam of coal. Borehole No. 3, at a depth of 608 feet, revealed the first coal-seam, 142 feet thick; at 633 feet, the second, 12 feet thick; at 662 feet the third, 1 foot thick, and at 692 feet the fourth, 4 1/2 to 5 feet thick. The borehole was stopped at a depth of 715 1/2 feet.

Jan 1, 1877

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart' reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,' and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By W. H. Ashby, R. W. Cassingham, C. R. Blomberg, J. B. Justins

The Brookhaven field is one of several Basal Tuscaloosa reservoirs located in south-central Mississippi. It is a standstone reservoir, of erratic deposition and with several faults, having an approximate subsea depth of 9,800 ft. A large variation in permeability exists with a weighted average being 256 md. Estimated average interstitial water saturation is 45 per cent. The undersaturated reservoir fluid exhibits marked differences in physical properties with measured saturation pressures ranging from 733 to 2,255 psi. Early rapid decline in reservoir pressure caused the operating interests to unitize the field and initiate a program of pressure maintenance by gas injection. At the time gas injection was commenced, the reservoir pressure had fallen to nearly half of the original pressure with only 4.5 Per cent of the original oil in place produced. The reservoir pressure has since been maintained at approximately 2,750 psig, and cumulative production to date is 17 per cent of original oil in place. An analysis of field performance during gas injection is presented in detail. The program of pressure maintenance by gas injection is considered to be a success, since the expected ultimate recovery has been increased and the current production rate is in excess of 2 per cent of original oil in place per year. Performance has been better, anticipated ultimate recovery is larger, and total production costs are lower than for a similar Basal Tuscaloosa reservoir nearby, even though that field appears to have a more effective natural water drive. INTRODUCTION The history of the Brookhaven Unit is a testimonial for unitization and for the application of engineering techniques in the operation of an oil field. The operating and royalty interests in this field have mutually benefited from their early recognition of the need for unitization and pressure maintenance and from the forthright manner in which these were accomplished. The tangible benefits accruing to the participants in the Unit are: (1) income from gasoline plant products, (2) reduced lifting and operating costs from those of competitive operation, (3) maintenance of high levels of current income by mitigation of the inevitable decline in production rates inherent to natural depletion, (4) an increase in ultimate recovery of about 40 per cent over natural depletion operations. This paper should properly be considered a progress report; however, the performance of the field after five years of pressure maintenance clearly indicates that the ultimate success of the project is assured. LOCATION AND GEOLOGY The Brookhaven field is located in south-central Mississippi, about six miles from the town of Brookhaven. Production at Brookhaven

Jan 1, 1955

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

By W. M. Baldwin, C. R. Johns

Cobalt is reported1,2 to scale in accordance with the Pilling and Bed-worth3 parabolic law: where w = weight increase per unit surface area K = constant l = time The reported values of the parabolic oxidation constant, K, in the temperature range 600 to 1100°C follow an Arrhenius type of equation as inspection of Fig 1 shows. According to Valensi's theory5 on the scaling of metals where multiple-layered scales (for example, MeX, MeX2, and others) are possible, this fact could be construed as indicating that a single oxide only is formed on cobalt in this temperature range. Since the single straight line extends above 920°C where only CoO is stable in air (see Fig 2) it might be inferred that this is the only oxide formed on scaling. Arkharov and Voroshilova10 have studied the scales formed when cobalt is heated in air in the temperature range 385 to 800°C and report that CoO is indeed found in the scale but that CoO4 is also found as an overlay and in increasing amounts in the lower temperature ranges. No quantitative data regarding the relative proportions of the two oxides were reported. Again in the light of Valensi's theory this would indicate that the straight line in Fig 1 would be expected to undergo an inflection at some point in the temperature range 385 to 800°C. Chauvenet2 has studied the oxidation rates of CoO to Co3O4 and has found this reaction to proceed parabolically with time but reports parabolic scaling rates which are considerably (about ten times) larger than the scaling rates of cobalt metal itself. This is difficult to explain in terms of Valensi's theory although a full discussion of the possible discrepancy cannot be made in view of the lack of sufficient data. These points made an investigation of the scaling behavior of cobalt in air an attractive study. Discussion of Results Relatively large (approximately 95 sq cm of surface area) samples of 0.020 in. thick electrolytic cobalt strip,* sanded with 2/0 paper, were heated in air in a cyclone type furnace. The samples were weighed before and after the scaling treatment. The weight increases so observed obeyed the Pilling and Bedworth parabolic law at all temperatures studied. The parabolic scaling constants when plotted on a logarithmic scale as a function of absolute temperature are reproduced

Jan 1, 1950

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at'ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936