Search Documents

By A.A. Grubb, F.L. Wolf

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By N. Shiarella, Coleman D. Hunter, I. B. Browning

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By I. B. Browning, N. Shiarella, Coleman D. Hunter

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By W. E. Crawford

The Fresnillo Company's mill at Fresnillo, State of Zacatecas, Mexico, treats oxide ores from the Fresnillo mine, dump ores and underground ores from the Plateros district, company leases and custom ores from the Zacatecas district, custom ores from other districts and tailings from old dumps at Fresnillo. The normal capacity of the mill is approximately 2600 dry short tons per 24 hours (a ton of 2000 lb.). The final product of the mill is a precipitate containing gold and silver, which is smelted and shipped as doré bullion to the refinery of the Compania Minera de Penoles, S.A., at Monterrey, State of Nuevo Leon, Mexico. The geology of the district was described in 1923, by T. C. Baker,' from whose paper the following data have been taken: The mineralization of the district was effected in the Tertiary period, following the intrusions and preceding the appearance of the flows. The area within which productive veins have been found is 1 mile long by 1/2 mile wide. The important units of each of the four general fracture systems meet in the central portion of Proano hill, which is an outcrop of graywacke, and where the rock was also intensely fractured by subsidiary movements, resulting in a shattered zone 1200 ft. long by 400 ft. wide. The mineralization was more intense in the immediate vicinity of the principal channels through which the solutions rose. The valuable metals are silver and gold, the ratio by weight of the former to the latter being 1000 to 1.5. Argentite is the predominant silver mineral, and is associated with pyrite and manganese mineral. The sulfides are primary throughout. A slight secondary action is represented by small quantities of native silver and silver halides, principally cerargyrite, which are found in the upper part of the mine. Oxidation has penetrated with great thoroughness to the lowest horizon so far exposed, this being 420 ft. below the present ground-water level. The shattered mass within the central portion of the hill and near the surface was sufficiently mineralized to produce a large stockwork

Jan 1, 1935

By N. R. Pillai, T. R. Anantharaman

THE striking alterations in the constitution and structure of cast A1-Si alloys brought about by addition of small quantities of some elements, particularly sodium, have been extensively investigated. Many theories' have also been propounded to explain this so-called lLmodification" process, but their main concern has been more to throw light on the action of sodium than to arrive at general criteria underlying this interesting as well as intriguing phenomenon. Such theories have generally dealt with one or more, but not all, factors that seem to have a direct or indirect influence on the cast structure of A1-Si alloys, e.g.., formation of ternary eutectic, removal of oxides, hydroxides, and so forth, by fluxing, morphological changes in silicon, and inhibition of growth of silicon grains through colloidal action, compound formation, preferential adsorption, or reduction of surface tension. Kim and Heine2 were the first to study the modification of A1-Si alloys in a systematic as well as comprehensive manner and to list the important characteristics of a satisfactory modifier. According to them, an important property of the modifying element is its capacity to form a stable compound with silicon in the appropriate temperature range. Other subsidiary requirements are that the element should get adequately dispersed in the melt at the inoculating temperature and also must not form stable compounds with aluminum. The alkali elements, with the exception of lithium, fulfill these requirements most satisfactorily and have been shown to be successful modifiers by these workers. Sodium is the most effective of these and seems to be in a class by itself for various reasons noted by earlier investigators.37 None of the other elements tried by Kim and Heine, viz., Mg, Ca, Cd, Zn, In, Pb, P, As, Bi, S, and Se, showed any significant modifying action. We wish to report here briefly on substantial modifications in cast eutectic A1-Si alloys brought about by some V group elements, which do not comply with the Kim-Heine requirements. Aluminum and silicon used in the present work were indigenous and had purities of 99.8 and 99.5 pct, re-

Jan 1, 1969

THERE is probably no phase of basic open-hearth steelmaking that is more of an art and less of a science than mold and pouring practice. It varies widely from plant to plant; consequently it is obviously impossible to set down in detail in this chapter the many ramifications of practice that are now used. The discussion that follows therefore attempts only to give an outline of the more common methods, with examples sufficient to indicate some of the variations in procedure, and to emphasize a few of the many underlying problems that face the open-hearth operator at the pouring platform. MOLD DESIGN Ingot molds are hollow castings of considerable wall thickness. Despite this, non-uniformity in wall thickness should be strictly avoided to prevent the setting up of unnecessary stresses. Molds are cast in various forms, sizes, and shapes depending on the type of steel, and on whether the ingot is to be withdrawn from the mold or the mold from the ingot. The selection of ingot-mold material, which is usually cupola or blast-furnace iron containing approximately 3.5 per cent carbon, 1 per cent silicon, 0.9 per cent manganese, 0.2 per cent phosphorus, and 0.07 per cent sulphur, is governed by numerous considerations that affect mold life. (1) Factors in addition to wall thickness that should be given primary consideration at the foundry are casting skin, shrinkage stresses, and casting temperature. Factors in Mold Design. In use, mold thickness is of greatest importance, for it must be heavy enough to freeze the molten metal rising in the mold and to reduce the temperature of the steel below that of the melting point of cast iron to prevent the inner surface of the mold from melting, which would result in the welding of the ingot to the mold. The skin of an ingot, which solidities immediately upon contact with the relatively cold walls of the mold, must soon become thick enough to contract on the fluid mass and pull away slightly from the sides of the mold. The separation of the ingot from the mold depends entirely on the heat taken up by the mold from the steel.

Jan 1, 1944

By C. W. Mason

TIN has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphur. The notorious "tin disease," which Cohen1 has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white 0 tin to cubic gray a tin, has apparently encouraged the expectation that one or more addi-tional polymorphic modifications might exist. The search for confirma-tion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but for previous assumptions. The ball apparently was started rolling in 1880 by Trechmann,' who reported a new modification of tin (y tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be y tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller.3 Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,6 by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) and stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencer3 in 1921 examined the above evidence critically; he found similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on a second lot of crystals, not described crystallographically.)

Jan 1, 1939

By H. R. Fife

AN extended study of dustproofing Freeport-seam coal has empha-sized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption proper-ties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measure-ments on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average ton of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by sur-face area. Wax extraction data on 1-in. to 0 slack from mine-run treated Free-port-seam coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness.

Jan 1, 1937

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

By R. W. Raymond

The Mining Law of New Pork, contained in Title XI., Chapter IX., Part One of the Revised Statutes, is as follows: Section 1. The following mines are, and shall be, the property of the people of this State in their right of sovereignty : (1.) All mines of gold and silver discovered, or hereafter to be discovered, within this State. (2.) All mines of other metals discovered, or hereafter to be discovered, upon any lands owned by persons not being citizens of any of the United States. (3.) All mines of other metals discovered, or hereafter to be discovered, upon lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain less than two equal third parts in value of copper, tin, iron, and lead, or any of those metals. Sec. 2. All mines and all minerals and fossils discovered, or hereafter to be discovered, upon any lands belonging to the people of this State, are, and shall be, the property of the people, subject to the provisions hereinafter made to encourage the discovery thereof. Sec. 3. All mines of whatever description, other than mines of gold and silver, discovered, or hereafter to be discovered, upon any lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain two equal third parts or more, in value, of copper, tin, iron, and lead, or any of those metals, shall belong to the owner of such land. Sec. 4. Every person who shall make a discovery of any mine of gold or silver within this State, and the executors, administrators, or assigns of such persons, shall be exempted from paying to the people of this State any part of the ore, produce or profit of such mine for the term of twenty-one years, to be computed from the time of giving notice of such discovery, in the manner hereinafter directed. Sec. 5. No person discovering a mine of gold or silver within this State shall work the same until he gives notice thereof, by information in writing to the Secre-

Jan 1, 1888

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923