Search Documents

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the winter of 1868-9, I was called upon by Professor F. H. Storer, to put up the Bunsen filter pump in the chemical laboratory of the Masschusetts Institute of Technology. As the laboratory is on the lower floor, it was found necessary to use a great deal of cumbrous pipe and apparatus to get the necessary column. It was then suggested that if an instrument could be devised which would make use of the hydrant pressure in the service-pipe, it would do away with the objectionable features of the Bunsen pump. After using the Bunsen pump for some years, the jet pump to be described in this paper was devised, and it has since been adopted by Prof. Wing in the quantitative laboratory of the school. I am much indebted to Prof. Wing for his aid in starting the manufacture in brass of these jet pumps, which are now to be had in Boston. The jet pump much resembles the Giffard injector in form. It differs from it in the fact that water is the impelling fluid, and air the impelled, while with the injector steam is used to impel water. The principle of condensation of steam, which is Water availed of in the injector, is entirely wanting in the jet pump. The jet pump consists in a water jet, w, (see figure), a constriction or waist, a, and a waste tube, o. The success of the jet pump depends on the following conditions 1. The relation between the sizes of sectional area of a and w. 2. The proximity of a and w. 3. The form and angle of the two hollow cones whose vertices make the constriction a. 4. The relative size of sectional area of w and o. 5. The zigzags, or an equivalent means of making foam. In the following discussion, let a, w, and o represent the diameters of these parts of the jet pump. A number of experiments were tried to ascertain

Jan 1, 1878

By R. C. Hyslop

The object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: 1. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. Theequipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. Laboratory Procedure With these ideas in mind, the problem was approached in the manner in which Koenigsbergerl developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change in the magnetic field intensity AZ due to the proximity of a specimen is given by: mk AZ = 2a2 Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. r.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1946

By William A. Longacre

IN a previous paper1 the author discussed the problem described by the title of this paper, outlining and reviewing the Gish-Rooney method, with comparison and brief analysis of the interpretation techniques of Roman2 and Tagg.3 Some aspects of the simple type of two-layer system were reviewed from various sources.4,5,6 THE TWO-LAYER PROBLEM For the configuration shown in Fig. I, and for any electrode separation A, the apparent resistivity is a function of the relative depth [HA], the overburden resistivity pi, and a factor K defined by the equation [ ] where p2 is the resistivity of the lower bed, Thus, by the known theory of electrical images, [ ] THE MULTILAYER PROBLEM As the number of isotropic, homogeneous, horizontal layers increases, the difficulties of interpretation multiply. The theory becomes much more involved, and in view of the state of our knowledge, the general problem is virtually impossible of exact solution. However, certain types of [ ] multilayer problems can be worked out in terms of two-layer theory. Hummel,7 Pirson,8 Tagg,3 Watson,9 and others have pointed out the possibility of building up approximations of multilayer resistivity curves with suitable combinations of two-layer curves. Many three-layer curves can be constructed in this way to a good degree of accuracy, and special types of four-layer curves can be approximated. It is very likely that as the number of layers increases, the method of combination will not give good approximations except in very special cases, In the analysis of actual field data, the author has found that many obviously multilayer curves can be solved partially with a good degree of accuracy, using the theory that thin adjacent beds may be considered as one layer or zone, and applying two-layer theory to the extremities of the field curve. MODIFIED TAGG METHOD OF INTERPRETATION Tagg's second method, though superior to his first, necessitates a large number

Jan 1, 1941

By William H. Hamilton

Tunnel-driving capabilities in terms of feet per hour have advanced several hundred percent in the last century. Indications are that this capacity will double each decade for the next three decades. These future improvements will be made possible by a greatly increased need for underground excavation and the awareness of industry of its own latent capabilities. The factors of most interest to any potential user of a tunneling machine are those making possible an increase in production. The first and most obvious factor, and probably the one that has created the excitement and interest of most people, is the increase in boring rate through faster rock fracture and improved support systems. Boring rate can be increased by more horsepower in the form of increased thrust, torque, and cutterhead speed, and by better cutters and cutting methods, better material-handling systems, and better ground-control systems. All of these items are extremely important and are the basis of much discussion and effort by everyone concerned with the excavation of tunnels by machine. The second factor, just as obvious and equally important as an increase in boring rates, is "increase in production through better utilization of the tunneling machine and related equipment," which means a reduction in downtime through greater reliability of equipment. Mechanical rock attack is presently capable of cutting hard rock at 5 fph and soft rock at more than 20 fph. In current practice, however, this advance rate is maintained for less than 50% of the shift time. I predict that tunnel-driving contractors and their supporting manufacturers of tunnel-boring equipment will provide machinery that will maintain these advance rates for more than 90% of the shift time. This increase in effective production will be due to the increase in reliability of the tunneling machine and tunneling system components. Such a percentage increase in utilization of the tunneling equipment is just

Jan 1, 1970

By M. J. Hordon, M. A. Wright

The well-defined increase in fatigue life observed o many metals cyclicly strained at vacuum levels below 10-1 to 10-3 torr has been attributed to the critical retardation of oxygen or water vapor chemisorption at the crack tip during crack propagation.1-3 In the absence of strongly adsorbed surface films, crack re-welding during cyclic compression or dislocation escape from the plastic zone around the crack tip has been proposed to account for the observed decrease in the rate of crack growth. The increase in the critical pressure required for the transition in crack growth rate with temperature experimentally determined for aluminum was found to be generally in accord with the adsorption rate model.4 However, although the adsorption mechanism would also predict an increase in transition pressure and fatigue life with increase in cyclic loading rate, and such effects were noted by Snowden5 for lead and Hordon3 for aluminum, the opposite results were reported by Kramer et al.B in studies on aluminum. The present note describes some recent measurements of the fatigue properties of 1100-H14 aluminum at low pressures to determine the specific effect of cyclic strain frequency in the transition pressure range. Flat cantilever-type specimens of 1100-H14 aluminum shaped to produce a uniform strain gradient along the gage length were tested in reverse plane bending at constant deflection amplitudes in two independent multi-specimen vacuum fatigue systems. One series of tests using 2-in. gage length specimens was conducted in an ion pumped apparatus with 107 torr and 50 cps capacity, denoted as Unit I, utilizing fixed mechanical cams to impose the strain amplitude. An independent test series using shorter 1-in. gage length specimens was conducted in a cryopumped apparatus designed for extremely low pressures below 10-10 torr, denoted as Unit II, using an electromechanical vibrator at non-resonant frequencies up to 150 cps to provide the deflection. Both vacuum fatigue units and associated test procedures have been described previously.3'7

Jan 1, 1969

While coal was undoubtedly seen by the early travellers within the state, the first mention of it was in the late 1820's when hunters put some stones from a creek bed under the logs of a large camp fire, and awoke later to find the stones on fire. The stream was later named Coal Branch; the location was at the eastern side of the present Bibbs County.1 In the Louisville Daily Journal of Feb. 11, 1831, the following short editorial note appeared: "Tuscaloosa Coal.-A small quantity of this article has reached Mobile, and has been tried in the office of the Patriot; it is said to be an excellent article. We invite such of our friends as desire economy in fuel, love a cheerful and constant fire, or would eschew a smoky room, to call and examine." On a geological map published in 1832, the "Carboniferous group" is shown and a spot near Tuscaloosa indicated as showing bituminous coal,2 and this is again alluded to in Morton's Synopsis, 1834. A brief description of the coal fields in the state in 1834 said that in winter coal was brought down the. Black Warrior River to Mobile and sold there at the same price as Liverpool coal, $1.00 to $1.50 per barrel, ($10 to $15 per ton) and that the writer was using it in his laboratory.3 At that time it was in local use by smiths and an iron foundry was using it in Shelby County.4 In 1836 some coal was mined in the Birmingham district, chiefly in the northern portion of the Coosa basin, where it was loaded on barges and taken down the Coosa Rivers.5 "William Whitman dug coal out of Wolf Creek (Walker County) in 1837," and in the same county, in 1839, the first coal shaft in the state, was sunk. This was near the mouth of Lost Creek and was known as Frierson's Shaft. It was operated by a hand windlass, using two tubs.1

Jan 1, 1942

By P. E. Demmler

Phosphorus combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent, grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal Industry' gives the following: Superphosphate of calcium, 60 lb.; granulated copper, 30 1b.; finely powdered coal, 10 1b. Similar formulas are given by Brannt2 and others, and detail variations are covered by patents, such as those of L. A. Jeffs3 and H. A. Webster.4 Among the objections to this method of producing phosphor-copper are the large amounts of raw material and resulting slag to be handled, and the difficulty of getting a satisfactory fusion. S. Skowronski5 found that at 1300' C. (2372' F.) it was impossible to get a good fusion

Jan 1, 1921

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By J. Brian Eby

The Gulf Coast area of Louisiana enjoyed a particularly active and profitable year in 1939. Fifteen new producing structures were located and approximately sixty new producing sand horizons in old fields were opened in that period of time. The most important new discoveries are the Eola field, Avoyelles Parish, and the Paradis, St. Charles Parish. The Eola strike was indicated during December 1938, but the well was not placed on production until January 1939. Eola is particularly important because it was the first discovery of oil in a commercial quantity in the Wilcox formation in that area. Sid Richardson, of Ft. Worth, Texas, drilled the first well on the Haas Investment Company's property, which encountered the producing sand at a little below 8500 ft. Within the year 48 wells were drilled, 42 being commercial producers and 6 dry holes. The second most favorable discovery was the Paradis field, which was discovered by The Texas Company's Louisiana Land and Exploration Company's Paradis No. 1 well, in St. Charles Parish, just west of New Orleans. Detailed information concerning this field has not yet been made available but it is reported that the oil sand is as much as 175 ft. thick. The initial production indicated was 1750 bbl. daily and reports suggest a very large structure. In Calcasieu Parish the Humble Oil and Refining Company's Edge-wood Land No. 1 discovered gas in the Oligocene at a total depth of 7042 ft., in the Perkins area. Although two additional dry holes have been drilled in this prospect, it is still believed to have some merit. A new discovery is credited to Cameron Parish with the finding of Miocene oil in the Superior Oil Company's State No. 1 well in Grand Lake. The Chalkley field, Cameron Parish, is credited as a 1938 discovery but was largely developed in 1939 into one of the more important new fields. During the year 13 wells were drilled, 8 being oil wells and 5 dry holes. The oil is found in the Oligocene at depths of approximately 9000 feet.

Jan 1, 1940

By W. P. Shinn

In a paper contributed by W. A. Goodyear, M.E., on "Water Gas as Fuel," read at the Boston Meeting, February, 1883,* the following statenlent was made: "The latest experiments on a scale of some magnitude in our citier, in the way of heating buildings and furnishing power for manufacturing purposes, have been by the distribution of high-presslire steam through pipes laid in the streets. Hilt these experiments (1) have not hitherto been very successful; and when we consider the high cost and (2) the great and unavoidable loss of heat and power, which always accompany the conveyance of high-pressnre steam to any considerable distance in pipes, to say nothing of (3) certain practical difficulties in the management of the pipes themselves, (4) it is evident that all such methods must eventually disappear before a system which can furnish a cheap gas of great heating power, easily distributed wherever wanted, without requiring pipes to stand pressures of 50 to 75 pounds per square inch, and (5) without keeping the whole mass of ground in the streets through which it passes hot, gratis, for a distance of ten or fifteen feet, in all directions around the pipes!' For the purpose of controverting Mr. Goodyear's statements in regard to steam-distribution in cities, I hare numbered the points made in his indictment, my principal object being, not a professional discussion of the technical and theoretical merits of steam vs. watergas, but a simple statement of facts, in regard to the present state of the street system of steam distribntion. Taking Mr. Goodyear's points in their order: 1. Concerning what he terms " These experiments," saying that they " have not hitherto been very successful," I propose to show, that the problem of stearn-distribution has passed beyond the experimental stage, and that its practical solution is highly successful. This will be shown by the facts hereinafter fully set forth. 2. "The great and unavoidable loss of heat and power whicn always accompany the conveyance of high-pressure steam to any con-

Jan 1, 1884

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By J. Brian Eby

The Gulf Coast area of Louisiana enjoyed a particularly active and profitable year in 1939. Fifteen new producing structures were located and approximately sixty new producing sand horizons in old fields were opened in that period of time. The most important new discoveries are the Eola field, Avoyelles Parish, and the Paradis, St. Charles Parish. The Eola strike was indicated during December 1938, but the well was not placed on production until January 1939. Eola is particularly important because it was the first discovery of oil in a commercial quantity in the Wilcox formation in that area. Sid Richardson, of Ft. Worth, Texas, drilled the first well on the Haas Investment Company's property, which encountered the producing sand at a little below 8500 ft. Within the year 48 wells were drilled, 42 being commercial producers and 6 dry holes. The second most favorable discovery was the Paradis field, which was discovered by The Texas Company's Louisiana Land and Exploration Company's Paradis No. 1 well, in St. Charles Parish, just west of New Orleans. Detailed information concerning this field has not yet been made available but it is reported that the oil sand is as much as 175 ft. thick. The initial production indicated was 1750 bbl. daily and reports suggest a very large structure. In Calcasieu Parish the Humble Oil and Refining Company's Edge-wood Land No. 1 discovered gas in the Oligocene at a total depth of 7042 ft., in the Perkins area. Although two additional dry holes have been drilled in this prospect, it is still believed to have some merit. A new discovery is credited to Cameron Parish with the finding of Miocene oil in the Superior Oil Company's State No. 1 well in Grand Lake. The Chalkley field, Cameron Parish, is credited as a 1938 discovery but was largely developed in 1939 into one of the more important new fields. During the year 13 wells were drilled, 8 being oil wells and 5 dry holes. The oil is found in the Oligocene at depths of approximately 9000 feet.

Jan 1, 1940

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030' C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By J. Morgan Clements

The manufacture of coke in Peru, as practiced at the coalmines of the Quishuarcancha and Goyllarisquisca districts, is intermediate between the primitive coke-heap and the bee-hive oven. The method of coking is quite simple. In constructing the coal-heap, preparatory to burning, the ground is first leveled, and a simple stack of stone and clay is built, giving the bottom, to a height of 6 ft., approximately 6 ft. of external diameter. The size of the stack varies in different districts, but is generally 9 ft. high, and slightly smaller at the top than at the bottom. The walls of the heap are from 12 to 14 in. thick, which allows an inside diameter of from 3.75 to 4 ft. These walls are pierced at intervals by three or more tiers of openings or flues, connected with the central flue. The radial flues have a diameter of about 5 in. and are built with a gentle upward slope. The stack (shown in Fig. 1) is permanent; and in this respect the practice in Peru differs from other primitive practices in which nothing is permanent except the yard. Above the permanent 6-ft. portion of the stack there is added a cap of clay, about 3 ft. high, which contracts toward the top, where it has an inside diameter of about 2 ft. This clay cap is temporary, and frequently has to be renewed after each burning. Before charging the coal, there are first built, from the lowest tier of flues upon the ground, a number of temporary flues, leading from the central stack out to the edge of the coal-heap, and constructed of blocks of coal for the greater part of the distauce, the outer edge alone being of rough stoue. The coal is then piled up over these flues and around the stack to a height of about 6 ft. The bottom flues are the only ones that

Jan 1, 1905

By W. J. Sharwood

IN the cyanide process, gold and silver are dissolved from crushed ore as double alkali-metal cyanides, from which they may he precipitated by such positive metals as sodium (amalgam), aluminum, or zinc, or by electrolysis. Two extreme conditions may he noted. Some works, especially slime plants practising decantation, use a relatively large volume of solution-possibly 4 or 5 tons per ton of ore-nearly all of which may require precipitation, so that the solutions handled are of much lower value per ton than the ore. On the other hand, in some leaching plants it is possible to extract with very little solution, and to percolate some of this more than once through the charge before precipitation, so that the solution to be precipitated may he much less than half the weight of ore, and proportionally richer. Solution intended for further use need not have all its precious metal removed, but any that has to be thrown away should be impoverished as far as is economically possible. In spite of certain advantages possessed by other precipitants, zinc in some form has been almost universally used. In some of the first attempts to utilize cyanides as gold solvents, a "piece or plate of zinc" was suggested as a precipitant, but extension of surface was early recognized as a desideratum. Macarthur and the Forrests adopted a "metallurgical filter" of zinc shaving, turned from disks or rolled sheets. They had previously experimented on other forms of zinc, and Macarthur records having tried zinc dust, which had of course been long known as a general reducing agent. It had also been known and used as a precipitant of precious metal from plating and photographic solutions, and comminuted zinc had been patented for recovering copper, etc., from ore leaches. Other inventors proposed the virtual making of zinc powder by the attrition of balls of zinc, and by similar means, during the passage of a stream of gold-bearing solution.

Jan 9, 1917

By W. F. Netezband, E. H. Crabtree

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By E. H. Crabtree, W. F. Netezband

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By N. Jaffe, J. E. Dorn

The effect of stress on the creep rate of high-purity poly crystalline aluminum in the intermediate temperature range was investigated by conducting creep tests at a series of different stresses and by decreasing the stress abruptly during the course of primary and secondary creep. Three series of decreases in stress tests were conducted: the stress was decreased in primary and secondary regions of creep at 347.5°K and the stress was decrensed in primary creep at 327°K. The results demonstrate the effects of structure and temperature on the stress dependence of the creep rate. The trends in the creep rate after a drop in stress are complicated and show that recovery takes place. The experimental results were compared with Friedel's theory for cross-slip, the experimentally determined energy for a constriction being in good agreement with the theoretical estimate proposed by Stroh. PREVIOUS investigations have shown that the ap-- parent activation energy for creep of polycrystalline aluminum, over the range from about 250° to 380°K, is approximately 27,400 cal per mole,' a value that is to a first approximation insensitive to the applied stress, the creep rate, and the creep strain. Several facts strongly support the thesis that creep, in this temperature range, is controlled by the rate-determining mechanism of cross-slip: 1) Recovery of the cold-worked state can take place by a number of mechanisms prominent among which is climb and cross-slip. Astrom2 reported rapid recovery of cold-worked polycrystalline aluminum at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at the higher temperatures of 455° to 478°K giving an activation energy of 36,000 cal per mole. Whereas the latter process was clearly identified with the climb mechanism, the former process. which has an activation energy in good agreement for that of creep in the same temperature range, is most likely due to recovery by thermally-activated cross-slip. 2) Single crystals of aluminum exhibit sharp slip-

Jan 1, 1962

By John Chipman

HE lecture on 'Thermodynamic Properties of Blast Furnace Slagso prepared in 1959 and published two years later required revision in one particular before it appeared in print. The activity of SiO, was deter mined through studies of the equilibrium: SiO, (in slag) 2C (graphite) = (in Fe) 2C0 (1 atm) The ratio for each experimental temperature was found from the heat of formation of cris-tobalite, the entropies and heat capacities of the re-actants, by virtue of the third law of thermodynamics. Discrepancies between several kinds of data led to investigations regarding other equilibria involving SiO, on the suspicion that there might be an error in the third-law value of its free energy. In particular the equilibrium: was restudied by Kay and Taylor who Confirmed the earlier results of Baird and Tayloron which their SiO, activities depended. The free energy of Sic was also rechecked4 independently. These and other equilibrium measurements led to the conclusion6 that the free energy of SiO, at high temperatures is in error and requires a correction of about -5 kcal. The exact source of the error is uncertain; it could lie either in the entropy of SiO, or in its heat of formation, but it more probably lies in the latter. Adjustment of this free energy lowers the ratio by a factor of approximately 4. Accordingly it will be necessary to multiply by this factor all of the SiO, activities determined by this method.',B Referring to the lecture cited, this correction should be applied in Figs. 8, 9, 10, 19, and 20. It applies also to the experimental data of Fig. 13, bringing these as well as those on the ternary system into good agreement with the work of Taylor and associates. At the same time it eliminates the discrepancy shown in Fig. 11, lowering both lines until the upper

Jan 1, 1962