Search Documents

By R. U. Jackson

Belt conveying is a method of transportation that requires proper servicing and maintenance if completely economical results are to be obtained from the system. With a trucking system, it is common practice to deliver the trucks to a servicing station each day or at the end of each shift. With railroad transportation there is a similar procedure. Sufficient credit is seldom given to this periodic inspection and maintenance procedure, yet it is the key to the successful operation of trucking and rail haulage systems. How about the belt conveyor transportation system? Here is a system that requires no operator for each individual unit. It requires only a main switch and an adequate sequence interlocking system, and the system is so simple to operate that maintenance is considered as only a casual requirement-nothing is done about it until after trouble has developed.

Jan 1, 1956

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs' scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By O. P. Chisholm

Dross emerges from the blast furnace either with the lead through a lead well or by tapping from a forehearth or settler, but until a dozen years or so ago few dross reverberatories were used in western lead smelters because it was the usual procedure to circulate the dross from the drossing lead kettles back to the blast furnace. It was quite customary for lead smelters to produce matte in their blast furnaces, as this was the form in which copper could be collected, concentrated if necessary, and shipped to the copper smelters for further treatment. The main prerequisites for good matte formation arc., of course, a more or less definite amount of copper on the charge and sufficient sulphur. Such troublesome impurities as arsenic and antimony were ignored, in so far as possible, although they contaminated the bullion and thereby increased refinery costs. At the same time stocks of blastfurnace speiss containing gold, silver, lead and copper in addition to iron, arsenic and antimony, were being accumulated for want of a market to absorb them. As the dross was being fed back to the furnaces as rapidly as it was being produced, arsenic and antimony tended to build up until the arsenic could effect a combination with copper and iron and an alliance with lead, and the antimony a combination with copper and an alliancc with lead. Sulphur, being the most active agent in taking up the copper, left little of that element for the arsenic and antimony, so that on the whole a somewhat unsatisfactory metallurgy resulted. During this same period, certain lead plants were beginning to encounter trouble with zinc due to the replacement of crude ores of lot zinc content by concentrates containing high percentages of lead and zinc in sulphide form, the blast-furnace slags resulting from the smelting of such concentrates being characterized by a decidedly increased zinc content. It was soon realized that zinc plus sulphur was "poison" to a lead blast furnace and steps were taken to reduce the sulphur content,. At this stage some plants found that any substantial matte fall was out.

Jan 1, 1937

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By Alan Morris

SEASON cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes are fairly well understood and means for its prevention are inexpensive and effective, .so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free- from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,1 in discussing a paper by Hatfield and Thirkell, says : "He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultane-us corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack.

Jan 1, 1930

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

[ ]

Jan 1, 1938

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

Jan 1, 1920

The discovery of nickel at the Wallace Mine in 1846, recorded in the Report of Progress of the Geological Survey of Canada, 1.848-49, was not the first find in the Sudbury mining district. As long ago as 1770 a company had been formed to work the rich deposits of, copper whose existence was then known. .But it was during the first mentioned year that, incited thereto by fresh finds and a favorable report by Mr. W. E. Logan, then Provincial Geologist, two [ ] groups of Canadians organized "The Montreal Mining Company and "The Upper Canada Mining Company." By the former company the Bruce Mines Location&apos; was purchased and work was immediately commenced upon it. The Wallace Mine acquired by the Upper Canada Mining Company, was abandoned after a shaft had been sunk and a few test pits opened.

Jan 1, 1907

By Jerry G. Rose, Robert C. Howell

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14 000 kPa (2000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room and-pillar mines so that a substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction became of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal- crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 3, 1979

By J. H. Nelson

An outline survey of the economic outlook for the United States export trade in petroleum products resolves itself broadly into two general divisions; first, a consideration of our present position in this trade, and second, a discussion of the visible factors which promise to affect appreciable changes in the immediate future in that trade. The United States PetRoleum Exports of majoR Petroleum Products 1925, 1926 and 1927

Jan 1, 1928

By R. D. Carnahan, J. E. White

A study of dispersion strengthening in TD-Nickel (nickel plus 2 vol pct Tho2) was conducted employing microstrain techniques at ambient room temperature. It was found that optimum strength was due primarily to the incorporation of stored energy developed by a variety of thermal-mechanical treatments. The relatively low strength of the recrys-tallized condition implies that the dispersed particles themselves offer only token resistance to deformation. The development of resistance to large-scale recovery or recrystallization at temperatures near the melting point requires a more extensive sequence of strain-anneal cycles than does the development of optimum strength. A micro-Bauschinger effect was observed which appears to be related to the lattice resistance to the movement of free dislocations. The effect was nearly identical to that in pure nickel indicating that the presence of the dispersed phase and considerably increased dislocation density (stored energy) only alters the number or effectiveness of barriers. THE early stages of deformation of engineering materials can be conveniently studied by utilizing strain-gage techniques which permit resolution of strains less than 5 X 10-7 in. per in. for testing in four-point bending (Carnahan and white1). The present investigation, part of a continuing study on the very early stages of deformation, was designed to reveal the true role of a dispersed phase in promoting high strength in a commercially available dispersion-strengthened alloy. Although this technique has been used for some time to study microdeformation in pure metals and alloys, it has just recently received attention as a means of investigating dispersion strengthening. Studying the very early stages of deformation in alloys which depend upon a finely dispersed inert phase for strength may prove to be a very important method for a better understanding of these materials. It is essential to obtain considerable clarification of actual dislocation movement and the kinds of deformation barriers which exist before optimum properties can be designed into this type of material with any degree of confidence. Considerable research on a variety of dispersion-strengthened materials has resulted in two different schools of thought regarding the strengthening mechanism. One faction2-4 favors the idea that the particles themselves resist the motion of dislocations. The criterion for yielding is the fracture of the dispersed second-phase particles due to an array of piled-up dislocations. Other invesfigators5-a have shown that particles are effective primarily by allowing a greater buildup of stored energy or dislocation density through thermal-mechanical treatments in the composite than the pure matrix material. The particles themselves, then, are not exclusive obstacles, but the complex network of particles, dislocation tangles, subboundaries, and grain boundaries are strength determining. The development of such a complex dislocation network in SAP has been studied recently in some detail by Goodrich and Ansell. The ability of dispersion-strengthened alloys to resist softening or recrystallization is also of considerable importance; however, the criteria for maximum stability may not necessarily be those for maximum strength. In this study, in addition to the evaluation of the microstrain properties of TD-Nickel, it is felt that considerable clarification of the true dependence of strength and stability on the dispersed phase is shown. I) MATERIAL AND PROCEDURE TD-Nickel is a dispersion-strengthened alloy developed by the E. I. DuPont de Nemours Co., which contains 2 vol pct thoria (Tho2) in a pure-nickel matrix. The average ThO2 particle size is approximately 0.1 p and the interparticle spacing is less than 1 u. The material was supplied by DuPont in two conditions: hot-extruded bar stock, and stress-relieved cold-rolled sheet 0.025 in. in thickness. The bar was extruded at 2200°F from a cold-pressed and sintered billet. The sheet stock was prepared from the extruded material by a process involving ten or more 50-pct cold reductions by rolling with intermediate anneals at 1800° to 2000°F. Test specimens used in this study were prepared in the form of rectangular parallelepipeds measuring 0.375 by 1.375 in. in thicknesses ranging from 0.025 to 0.040 in. Samples prepared from sheet and extruded stock were mechanically polished before heat treatment and were handled with extreme

Jan 1, 1964

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956