Search Documents

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By Larry Kaufman, Morris Cohen

THE solid phase equilibria' and the martensitic transformation in the iron-nickel system have been the subject of considerable study. In addition, there have been numerous investigations on the calorimetric and thermodynamic properties of iron-nickel alloys. The purpose of the present work is to extend the existing information concerning the martensitic reaction in the iron-nickel system, and to develop a general thermodynamic treatment which will encompass the equilibrium and non-equilibrium phase

Jan 1, 1957

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

By G. P. Connell, R. E. Gilmore, J. H. H. Nicolls

The purpose of this paper is to suggest a procedure for indicating the dividing line between noncaking coals and those that have weakly caking properties. A laboratory agglomerating test as an aid in classifying weakly caking coals is outlined and its merits in comparison with the standard agglutinating method advanced by the U. S. Bureau of Mines are discussed. No attempt, however, is made to discuss in detail either the different methods for determining "caking" and "agglutinating" indices or the various systems of classification. Two methods, differing somewhat in procedure, have been employed and recognized as suitable for determining the caking or agglutinating values of coals; namely, those in which an inert material such as sand, electrode carbon, etc., has been mixed with the coal before being heated, and those in which the coal is carbonized alone. In all such methods, the coal with or without the inert material is in the finely divided state and the index or value sought is derived from the examination of the residue after heating in a closed crucible or other container. The procedure outlined by Selvig, Beattie and Clellandl is the most recent representative of the method using sand as inert material, while the agglomerating test described below is representative of the method in which the coal is carbonized alone. The standard volatile-matter determination affords a means for observing the coking properties of a coal, and this has been described by Rose2 as the simplest of all coking tests. According to him, "the resulting coke button will indicate whether the coal is noncoking, feebly coking or strongly coking," despite the fact that "almost every condition in this test is at variance with large-scale carbonizing practice." Lessing,3 the

Jan 1, 1934

IT may perhaps seem to you that I have deviated from sequence by having entered into the narration of this arrangement of the bellows, but, although they are not furnaces or vessels for containing the melts, they are essential agents for bringing to port the bark of your labors. Returning to our regular pathway, and supposing that, besides making the moulds, you have melted and cast not only statues and bells but also guns, it is true that a certain procedure is required in order to finish them. For this you should have the moulds full, and they should have come out very well, for in truth reason does not allow that they turn out otherwise for one who uses precaution. [II2V] Then you have taken your casting from the pit and have freed it of clay. Since I have told you nothing beyond this, do not be dismayed if you see the castings so rough and in a form that scarcely shows what they really are, for I wish to open up part of the way into the great labor of finishing them so that it may seem to you that you have been somewhat helped by me. Therefore, when it is a gun, first see that the iron spindle that has been placed in the middle of the core is taken out. You can do this easily by striking the heel of the core, especially if the spindle had first been covered with ashes, hemp, or a little rope. Then saw off the feeding head above the mouth, using either a dun steel saw with tiny straight teeth that has been tempered with oil or some other fat, or a hay sickle whose edge is gently hit by a little hammer. Then have the clay that is attached to the curls or other bronze parts lifted away with a chisel. Then with a scouring brush and water uncover the emblems, coats of arms, borders, and cornices that you made as ornaments. Striking it with a hammer, push inwards every superfluous bit of bronze. Finally, having cleaned the bronze by washing, scraping, and cutting away every bit of clay, strike its surfaces gently with a large hammer and thus make it very smooth. Likewise finish the mouth and all its cornices as exactly and completely as possible with files and any other instrument that serves best. Then take a long, powerful tool that has some steel on the point, made like a chisel and somewhat bent, or with three points like the iron blade

Jan 1, 1942

THE Copperton mill in reality was a sort of proving ground. It was. designed to serve three purposes: (1) to verify the accuracy of the mine sampling by actually treating substantial tonnages of ore, (2) to demonstrate on a reasonably large scale the percentage of the copper in the ore that could be recovered, and (3) to permit the testing of various kinds of machines and devices for crushing and concentrating the ore, so as to guide the engineers in designing the proposed 6000-ton milling plant at Garfield. As a matter of fact, it contained a lot of second-hand equipment sent by MacNeill and Penrose from the works of the United States Reduction &Refining Co. in Colorado; and it was by no means a model installation. Probably it would have been even less efficient, except for the skillful work of George O. Bradley and-Frank-G, Janney, both of whom had worked with Jackling at Mercur. Bradley was a mechanical engineer employed to design the plant. Later he directed the design of the concentrator at Garfield and remained as consulting mechanical engineer to the company until 1915. Janney, who afterwards became manager of mills, a position that he retained until his death in 1916, was a skilled mechanic at the Golden Gate mill at Mercur when Jackling built the plant in 1897. His flair was making machinery do what it was intended to do. He was not an ore-dressing engineer in a technical sense; but Jackling him- self was a specialist in this respect as well as in designing and construction and Janney's mechanical aptitude made him a particularly valuable man in the Utah organization. John McDonald, another of Jackling's Mercur associates, was the first mine superintendent. With practically all of the available funds earmarked for construction of the Copperton

Jan 1, 1933

By Everette Lee DeGolyer

FIFTEEN thousand barrels of oil daily, the production of the United States 75 years ago, amounted to more than 90 per cent of world supply. Russia and Romania, neither of which produced as much as one thousand barrels daily, were the only other suppliers in substantial quantity. The adolescent oil industry of the United States, a dozen years old in 1871, was still confined to the Appalachian region. Wells were drilled by cable tools; many of them were "kicked down" by manpower with a spring pole; and depths were measured in hundreds rather than thousands of feet-a 1000-foot well was a deep well. Casing was an innovation, come into general use only a few years previously and still so new as to be subject to bitter patent litigation. Crude oil was packaged in wooden barrels and shipped by flat boat and barge on the creeks and rivers and by railroad. Such pipe lines as existed were only a few miles long. There were many refineries. Pittsburgh, Cleveland and the Atlantic seaboard were refining centers. Refineries were very small, however, and their operations consisted essentially in simple fractionation by distillation and treating for quality. The products in demand were burning oil or kerosene and lubricating oils. Oil was not yet used as fuel and gasoline was a nuisance to the refiner.

Jan 1, 1947

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Howard Reiss, C. S. Fuller

A theoretical and experimental study has been made of those interactions between holes and electrons which influence the solubilities of donors and acceptors in semiconductors. The major portion of the work concerns the solubility of lithium in silicon doped to varying degrees with boron. This solubility increases with increasing boron content in a manner predicted by theory and exhibits the expected temperature dependence. A qualitative experiment in germanium is described which demonstrates, in accordance with theory, that doping with a donor decreases the solubility of another donor. SEVERAL authors have discussed the possibility that holes and electrons behave like chemical entities and influence the solubilities of ionized impurities, Wagner was the first to invoke this concept in connection with his studies on nonstoichio-metric oxides. He used it again in explaining the solubility of hydrogen in molten binary alloys. In a theoretical paper,' Reiss drew attention to the fact that solutions of impurities in semiconductors

Jan 1, 1957

By Christopher G. Atwater

The object of this paper is to describe and discuss the progress that has been made, up to the present date, in the development of the modern by-product coke-oven. There are few members of the Institute who have not heard more or less of the by-product oven-installation, and there are many whose acquaintance with it is intimate and practical. Since the general opinion on the subject has hardly become crystallized as yet, it is hoped that this paper will at least furnish matter for discussion. In order to obtain an idea of the present status of the industry in the principal iron-producing countries, the following table has been prepared : Table Showing Proportion of Coke Made in By-Product Ovens in Various Countries. United Kingdom (1898, Mr. George Beilby). Short Tons. Per Cent. Coal coked in by-product ovens,. .. 1,400,000 7.9 Coal coked in blast-furnaces with by-product recovery,.......2,240,000 12.7 Coal coked in non-by-product ovens,. . 14,000,000 79.4

Jan 1, 1903

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reason- able expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In a bulk tonnage product such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: 1 (I) by screening or sizing, (a) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing,

Jan 1, 1943

By E. P. Jennings

Large deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archæan schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-cleposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained.

Jan 1, 1913

By C. D. Demond

In reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500" F. and another only 2,100 F., while the "critical" temperature is 2,000" F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature in a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 1, 1915

By G. L. Oldright

THE upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the opera-tion of sintering. A sinter feed with normal gangue constituents, con-taining more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead con-centrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1940

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Newell G. Alford

Forecasts of future timber consumption in soft-coal mining are handicapped by the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added composite figures for the continental United States in 1905 and 19191 and for central and western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928,000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross ban used per ton of coal mined and the percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 1, 1924

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946