Search Documents

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By John W. Langley

In the summer of 1888 it was the fortune of the writer to present the subject of the desirability of establishing a set of samples of steel, which should be analyzed with extreme care, in order that they might become standards to which scientific and commercial analyses of iron and steel could be subsequently referred; also, that greater uniformity in the results of analyses might be brought about, since these standards would bear towards analytical methods somewhat the position which the original units of weight and length, the gramme and meter, or the pound and yard, preserved in Paris, London, and Washington, do to the mechanical arts. The plan met with hearty co-operation, with the result that com mittees were appointed in Sweden, Germany, France, England, and America, to receive the material and to see that the necessary au alyses were executed. In England, the British Association for the Advancement of Science appointed a committee, which subsequently published a plan

Jan 1, 1891

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year's activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

By S. L. Hoyt

ABOUT three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. ? This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some com-ments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1.

Jan 1, 1937

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, '60, Chairman, Henry Krumb, '59, J Loveloy, '61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, '59, Chairman, C E Reistle, Jr, '59, Grover J Holt, '59, L F Reinartz, '59, M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, Augustus B Kinzel, ex off as President

Jan 1, 1958

THE CHAIRMAN (F. K. COPELAND,* Chicago, Ill.).-At this particular time conditions existing in this, country, and elsewhere, make all questions of milling or smelting or mining, or anything else, absolutely secondary to the one question of labor. We have always devoted our attention largely to the efficiency of machinery, and to reductions in costs, etc., and have let this tremendous problem of our relation to labor more or less take its own chances. There has never been a time when those who are responsible for the operation of business of different kinds were as com-pletely at a loss as they are now, so that anything that can be brought out that relates to labor is, to my mind, of utmost importance. T. T. READ, Washington, D. C.-This formulation of a method of curtailing forces at the Copper Queen is a notable step in advance of our treatment of personnel in the mining industry. So far as I know, it is the

Jan 12, 1919

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By G. F. Fix

Oil and gas activity reached a higher peak in Indiana during 1940 than for any like period during the past decade. Major activity, as during 1939, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin, where most of the increase was due to field drilling in previously proven areas. The amount of wildcat drilling was about the same as for 1939. No new fields of any apparent consequence were discovered during the year, with the possible exception of the College pool, in southwest Posey County. Only one well had been completed in this area at the end of the year. About 10 ft. of saturated Aux Vases sandstone was drilled in this well and the initial production was I00 bbl. of oil a day. Other discoveries during the year 1940 include: St. Thomas, in southwestern Knox County, where four McClosky wells, ranging from I00 to 300 bbl. a day initially, were com-pleted; Buff kin, in central Posey County, with 11 oil wells and 5 gas wells completed; and new developments in two old areas —Randolph County (part of the old Trenton field) and Gentryville, northwestern Spencer County, where some oil was found many years ago. The St. Thomas field proved disappoint-ing, with very spotty production from the McClosky horizon of the St. Genevieve limestone at a depth of about 1875 ft. The discovery well flowed 362 bbl. a day ini-tially. At the end of the year the field was pretty well outlined by dry holes and some inside locations were dry. The Buffkin pool also proved spotty, with production from shallow Pennsylvanian sands and from the Basal Pennsylvanian Mansfield sandstone, the latter at a depth of approximately I175 ft., with small production from the Cypress sandstone of Chester age. Oil wells in this pool are small, ranging from 25 to 75 bbl. a day. The Randolph County area, on the east side of the Trenton gas field, showed some promise for a commercial gas field, with four completed gas wells having cumulative initial flows of about 1,200,ooo cu. ft. a day. The area appar-ently was not depleted during the Trenton boom at the turn of the century, since casing pressures are about as high as the virgin pressure in the old field. Elsewhere the pressure has dropped as low as 5 pounds. The Griffin field received most of the drilling during 1940, with 163 completed oil wells. This field now covers about 3200 acres on the Indiana side of the Wabash River and is not as yet completely delimited. It produced the major part of Indiana's oil during the year—a total of 3,594,000 bbl. At the end of 1940, there were 253 producing wells in Griffin. New Harmony had five completions for a total of 24. The Rockport field, in Spencer County, continued to be actively developed and had a total of 45 gas wells and 9 oil wells at the end of the year. Oil in commercial quantities had not been found in the field previous to 1940. Total gas production for the year was 394,470,000 cubic feet. In all, 521 wells were drilled in the state during 1940, as compared to 377 for 1939. Of this number 248 were oil wells, 77 were gas wells and 196 were dry. Divided into

Jan 1, 1941

By G. F. Fix

Oil and gas activity reached a higher peak in Indiana during 1940 than for any like period during the past decade. Major activity, as during 1939, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin, where most of the increase was due to field drilling in previously proven areas. The amount of wildcat drilling was about the same as for 1939. No new fields of any apparent consequence were discovered during the year, with the possible exception of the College pool, in southwest Posey County. Only one well had been completed in this area at the end of the year. About 10 ft. of saturated Aux Vases sandstone was drilled in this well and the initial production was I00 bbl. of oil a day. Other discoveries during the year 1940 include: St. Thomas, in southwestern Knox County, where four McClosky wells, ranging from I00 to 300 bbl. a day initially, were com-pleted; Buff kin, in central Posey County, with 11 oil wells and 5 gas wells completed; and new developments in two old areas —Randolph County (part of the old Trenton field) and Gentryville, northwestern Spencer County, where some oil was found many years ago. The St. Thomas field proved disappoint-ing, with very spotty production from the McClosky horizon of the St. Genevieve limestone at a depth of about 1875 ft. The discovery well flowed 362 bbl. a day ini-tially. At the end of the year the field was pretty well outlined by dry holes and some inside locations were dry. The Buffkin pool also proved spotty, with production from shallow Pennsylvanian sands and from the Basal Pennsylvanian Mansfield sandstone, the latter at a depth of approximately I175 ft., with small production from the Cypress sandstone of Chester age. Oil wells in this pool are small, ranging from 25 to 75 bbl. a day. The Randolph County area, on the east side of the Trenton gas field, showed some promise for a commercial gas field, with four completed gas wells having cumulative initial flows of about 1,200,ooo cu. ft. a day. The area appar-ently was not depleted during the Trenton boom at the turn of the century, since casing pressures are about as high as the virgin pressure in the old field. Elsewhere the pressure has dropped as low as 5 pounds. The Griffin field received most of the drilling during 1940, with 163 completed oil wells. This field now covers about 3200 acres on the Indiana side of the Wabash River and is not as yet completely delimited. It produced the major part of Indiana's oil during the year—a total of 3,594,000 bbl. At the end of 1940, there were 253 producing wells in Griffin. New Harmony had five completions for a total of 24. The Rockport field, in Spencer County, continued to be actively developed and had a total of 45 gas wells and 9 oil wells at the end of the year. Oil in commercial quantities had not been found in the field previous to 1940. Total gas production for the year was 394,470,000 cubic feet. In all, 521 wells were drilled in the state during 1940, as compared to 377 for 1939. Of this number 248 were oil wells, 77 were gas wells and 196 were dry. Divided into

Jan 1, 1941

By S. F. Frederick, G. F. Pittinato

The deformation mechanisms operating in Ti-5Al-2.5Sn at 20°K under uniaxial and biaxial stress fields were determined by using both optical and electron microscopy. In the uniaxially stressed specimens, de-fu~rnation twins were found only in the immediate vicinity of the fracture. Twinning was, however, established as a deformation mechanism under biaxial stress conditions. The same slip systems were opera-tiz,e under both uniaxial and biaxial stress. Prismatic slip was identified as the major slip syslem; however, basal and first-order pyramidal slip also occurred, but to a lesser degree. The interaction of moving dis-locations on intersecting slip planes resulted in the formation of jogs and dipoles. Hexagonal dislocation networks were formed only under biaxial stress conditions. A discussion is given on the formation of hexagonal dislocation networks. IT has been shown that titanium alloys can exhibit unusually high strengths when tested in a biaxial stress field.'-" The high biaxial strengths are a consequence of a strong basal plane sheet texture which results in distinctly anisotropic flow properties. This texture strengthening appears to decrease with decreasing temperature2 and would seem to indicate a change in deformation modes. For example, in a uniaxial tensile test, Ti-5A1-2.5Sn yields isotropically at 20°K but is strongly anisotropic at room temperature. The increase in biaxial ultimate over uniaxial strength at 20°K is also much less than at room temperature. It is known that titanium car] form deformation twins more readily at cryogenic temperatures than at room temperature.4 Since the formation of deformation twins will reduce the degree of basal texture in sheet material,' an accompanying decrease in texture strengthening would be expected. To investigate more fully the nature of texture strengthening at cryogenic temperatures, the deformation modes of Ti-5A1-2.5Sn tested in uniaxial and 1:1 biaxial tension at 20°K were studied by optical and electron transmission microscopy. EXPERIMENTAL PROCEDURE The uniaxial and biaxial stress test specimens were prepared from 0.020-in. thick sheets of Ti-5A1-2.5Sn ELI having the composition shown in Table I. Uniaxial stress conditions were obtained by using flat tensile specimens machined from the sheet material. The longitudinal axis of the tensile specimens was aligned perpendicular to the rolling direction of the sheet. Tile biaxial test specimens were prepared by rolling precut, 19-in.-lengths of sheet into 4-in.-diam cyl- inders. Following longitudinal butt welding, the cylinders were stress relieved at 1000°F for 4 hr. A 9-in. sq "window" was then chemically milled into each cylinder's surface reducing the wall thickness in the milled area to approximately 0.006 in. The testing procedure consisted of pressurizing the cylinders while simultaneously applying a tensile load. Using this technique, a 1:l axial to hoop stress was obtained. Complete details of the specimen and testing procedures are given in Refs. 1 and 2. The biaxial and uniaxial stress specimens were all tested in liquid hydrogen. Specimens for electron transmission microscopy were prepared by first chemically milling to a thickness of about 0.001 in. followed by electrolytic polishing to electron transmission thickness. The chemical milling solution, consisting of 800 ml of water,

Jan 1, 1970

By R. V. Norris

1. INTRODUCTION. THE anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, in the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which,, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jun 1, 1911

By Arnulf Muan, R. E. Johnson

Equilibrium CO2 /CO ratios of a gas phase coexisting with selected oxide phase assemblages of the system CaO-"Fe0"-SiOz and vnetallic iron have been determined at 1080°C. The data obtained are used to calculate activity-conzposition relations for metasili-cute, orthosilicate, and CaO- "FeO" solid solutions, and to determine a new value for the free energy of formation of C&S&0,. The metasilicate solution is practically ideal, whereas large deviations from ideality exist in the othe,r two solid solutions. BECAUSE of the geochemical and metallurgical importance of the oxides CaO, "FeO", and SiOz, the system CaO-"FeO"-SiO2 has been the subject of several experimental studies during the past 30 years. Following the delineation of phase relations at liquidus temperatures by a group of investigators at the Geophysical Laboratory of the Carnegie Institution of Washington in 1933,1 Chipman and associates in the early forties2,3 determined activities of FeO in liquids of this system. Since that time, many attempts have been made to interpret the data of Chipman et al. in terms of the constitution of the silicate liquids and the interaction parameters among the various constituents of the system (see for instance papers by Richardson4 and by Flood and coworkers5). One of the assumptions made in some of these interpretations4 is that the binary silicate systems CaSiO3-FeSiO3 and CazSi04-Fe2SiO4 mix ideally in the solid state. The objective of the present study is to provide experimental data on activity-com position relations in solid solutions of the system CaO-"FeO"-SiO2. Such data will contribute toward an understanding of the thermodynamics of silicate solid-solution phases in general, and will serve specifically to confirm or refute some of the assumptions made in interpreting liquid slag behavior. PREVIOUS WORK Phase relations in the system CaO-"FeO"-SiO2 in contact with metallic iron were determined by Bowen, Schairer, and Posnjak,1 and additional phase-equilibrium data for this system have been presented by Allen and snow.' A reproduction of the most up-to-date phase diagram for this system is shown in Fig. 1.7'8 Of particular interest in the present investigation are the relations among the various crystalline phases slightly below the lowest solidus temperature in the system, as shown in Fig. 2. The present work will be concerned primarily with some of the composition

Jan 1, 1968

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906