Search Documents

Jan 1, 1924

By T. Sterry Hunt

THERE are about sixty bodies which chemists call elements ; the simplest forms of matter which they have been able to extract from the rocky crust of our earth, its waters, and its atmosphere. These substances are distributed in very unequal quantities, and in very different manners. As regards the frequency of these elements in nature, neglecting for the present those which constitute air and water, and confining ourselves to the solid matters of the earth's crust, there are a few which are exceedingly abundant, making up nine-tenths, if not ninety-five hundredths, of the rocks so far as known to us. The elements of which silica, alumina, lime, magnesia, potash, and soda are oxides, are very common, and occur almost everywhere. There are others which are much rarer, being found in comparatively small quantities. Many of these rarer elements are, however, of great importance in the economy of nature. Such are the common metals and other substances used in the arts, which occur in nature in quantities relatively very minute, but which have been collected by various agencies, and thus made available for the wants of man. It is chiefly of the well-known metals, iron, copper, silver, and gold, that I propose to speak to-night ; but there are two other elements not classed among the metals, which I shall notice for the reason that their history is extremely important, and will, moreover, enable , us to comprehend more clearly some points in that of the metals themselves. I speak of phosphorus and iodine. You all know the essential part which the former of these, com-

By J. G. Savins

Certain types of macromolecules added to water and salt solutions flowing in turbulent motion can reduce the pressure gradient. Alternatively, the volumetric capacity of a pipe for these fluids is increased by the presence of these materials. Examples presented show that the drag reduction can become significant. Thus, the presence of 0.28 per cent of a gum derivative in a solution of sodium chloride flowing at 200 gal/min in a 1.89-in. pipe yields a pressure drop which is 0.44 of the single-phase drop measured under the same conditions of turbulent flow; the addition of 0.1 per cent of a vinyl derivative to a I-in. water line yields a throughput capacity which is 1.78 of the single-phase capacity at the same pressure drop. It is further shown that these phenomena are distinctly different from previous observations with other classes of non-Newtonian systems. There a simple lowering of friction factors below the levels predicted from the resistance laws for Newtonian fluids is associated with a suppression of turbulent motion. A rational physical explanation for drag reduction is advanced. Briefly, the proposed mechanism is a storage by the molecular elastic elements of the macromolecules in solution of the kinetic energy of the turbulent motion. INTRODUCTION This study was inspired by a recent review of some paradoxical drag reduction phenomena in turbulent pipe f1ow.I Under very moderate conditions of turbulent flow, the pressure gradient necessary to pump solutions containing certain specific kinds of polymers, fibers and metallic soaps may become appreciably lower than that required* to pump the solvent, i.e., water or a low-viscosity hydrocarbon, under identical flow rates in the same conduit. As shown by our review, this phenomenon of drag reduction in turbulent duct flow was first noted during the second world war, apparently arising in connection with the development of flame warfare weapons. Since that time several papers illustrating this phenomenon have appeared: Toms, Oldroyd,3 Agoston et al., Bundrant and Matthews, Robertson and Mason,6 Ousterhout and Hall,7 Daily and Bugliarello~ Lummus, Anderson, and Fox. 9 That there are practical applications for techniques which increase discharge or decrease the pressure necessary to transport a liquid through a pipeline is illustrated in the patents which have issued which take advantage of this peculiar phenomenon, e.g., Mysels,l0 Dever, Harbour, and Seifert.11 One also finds fragmentary evidence of this effect in the data pertaining to a few of the polymeric solutions studied by Shaver12 and Dodge.13 However, these investigators were concerned with the development of friction factor vs Reynolds number correlations for a variety of non-Newtonian solutions and suspensions, rather than in a study of drag reduction-. A similar kind of drag reduction effect has been observed in gases. Sproull, for example, reports that adding dust to air flowing in turbulent motion through a pipe results in a lowering of the pressure gradient at identical flow rates. There are also military applications for reducing the drag on hydrodynamic vehicles. For example, the possibility of injecting a rheologically complex fluid into the boundary layers of bodies to reduce the skin friction has been investigated by Fabulal5 and Granville.16 Along somewhat different lines are the drag reduction studies of Kramer.17118 He has shown that skin friction can be reduced by covering the surface of a vehicle with a flexible skin. The effect is apparently due to the boundary layer being stabilized by the presence of the skin. Drag reduction by means of coexisting gas and liquid boundary layers, e.g., film boiling and continuous gas injection, has been proposed by Bradfield, Barkdoll, and Byrne,19 Cess and Sparrow,20'21 Sparrow, Jonsson, and Eckert.22 Here the skin friction occurs between a vapor and a surface rather than between a liquid and a surface. There are several references in the literature to friction-factor correlations for non-Newtonian solutions and suspensions: Shaver and Merri11,23 Dodge and Metzner, Clapp,25 and Thomas.26

Jan 1, 1965

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By P. K. Lucke

ONE of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebOdies occurred. This table land lies at altitudes ranging from 4000 to. 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. FIG. 1. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulphides above, and I will endeavor to explain the causes of the phenomena in certain specific instances.

Jan 6, 1918

By Kenneth Robertson

ALL, strangers visiting this district are struck with the peculiar manner in which the pig-iron is graded. There are eleven regular grades, besides which, when gray forge is ordered, one-half of Nos. 1 and 2 Mill are shipped. Occasionally there is another grade Known as Silver Mill, which is made so seldom that I cannot describe it, and have no sample to exhibit. Most of you have found it difficult to grade properly and uniformly under the simpler system which obtains elsewhere, and can consequently readily imagine the increased difficulty with us. Each furnace employs an " expert," and even with this precaution, the system is not conducive, at all times, to amicable relations between buyers and sellers. I am told that it was adopted at the time Southern irons were seeking a market; but it still remains, although the time has come when our iron is sought for and has obtained for itself a place in the markets of the country. The grades are as follows:

Jan 1, 1889

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By R. M. S. B. Horta, W. T. Roberts, D. V. Wilson

Evaluation of results obtained by the Harris method for inverse pole figures is discussed. Two existing analyses and a new approach are compared. In the most frequently used analysis, different reflections are accorded equal weight. A second method involves area-weighting of reflections, mainly to take account of nonuniformity of Pole distribution. In the new method, reflections are weighted according to their multiplicity factors. Intensity ratios obtained from a sample of steel sheet by the three methods are compared. INVERSE pole figures offer a convenient method of depicting the proportions of material with various orientations referred to a unique specimen axis. The technique was first applied to fiber textures, but it is now frequently used as a description of texture in sheet metal, the unique axis in this case usually being the sheet normal. The Harris method' for the determination of inverse pole figures has the great merit of simplicity. It suffers certain intrinsic limitations, but provided that these are borne in mind, the results allow useful conclusions to be drawn regarding the effects of texture components on certain mechanical properties. Much thought has been given to alternative methods of texture description, aimed at eliminating the ambiguity in the simpler methods.2"6 Refinements in the method of description are obtained at the price of increasing complexity, and it seems clear that a simple method, such as that of Harris, will continue to find application. The original derivation by Harris1 has been corrected by Morris7 and later by Mueller, Chernock, and Beck.2 Since the latter reference is more accessible, it is referred to more frequently than the work of Morris. Most users of the inverse pole figure method present their results on the basis of the treatment by Mueller et al., and it is the purpose of the present communication to comment on this treatment and to suggest a simple modification to the method of presentation which enhances the meaningfulness of the results. It will be convenient first to summarize the Mueller analysis as follows: The intensity Ihkl of a hkl reflection from a textured specimen is: Ihkl=CI0AL\Fhkl\2NhklPhkl [1] where C is a constant for a given sample I, is the intensity of the incident beam A is an absorption factor. With usual diffrac-tometer geometry and a flat specimen, A is inversely proportional to the density of the specimen. L is the Lorenz polarization factor Fhkl is the structure factor for the hkl reflection Nhkl is the multiplicity factor phkl is the fraction of crystals in the polycrystal-line aggregate with any particular (nkl) plane parallel to the surface. The corresponding equation for a specimen with randomly oriented grains is lR,hkl=CRl°ARL\fnkl\2Nnklk [2] the subscripts R indicating the factors that are different for the random sample, which will, in general, have a density different from that of the textured one. The intensity ratio is hkl , c A Phkl [3] IR,hkl CR AR PR The constants are eliminated by summing over all the measured reflections ^iRMi °R AR PR ljPkkl and from Eqs. [3] and [4] T IR,hkl The only unknown in Eq. [5] is Yj phkl and before this can be evaluated, it is necessary to adopt some form of normalizing procedure. Mueller et al. assume that when a large number, n, of reflections is used, the average value of p as defined by Eq. [6] below will be unity ? = £j**l3l [6] and the final result of their analysis follows: hkl Pkkl = i I&Jf~ [7] ±y* Ihkl ^ in,hki The normalizing procedure used by Mueller et al. involves an unrealistic assumption since it gives equal weight to each of the hkl reflections. Other normalizing procedures can now be examined with a view to selecting a more appropriate one. For an infinite number of reflections, the function p can be averaged over a continuous range of orientations covering the complete solid angle 4p by the integral relation: p =1 jp(a)dQ = l [8] This is the only exact procedure, but in practice a

Jan 1, 1970

By P. K. Lucke

One of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebodies occurred. This table land lies at altitudes ranging from 4000 to 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulfides above, and I will endeavor to explain the causes of the phenomena in certain specific instances. Case I.—Fig. 1 in this case shows that sulfides of lead remained

Jan 1, 1920

As already announced, the Arizona Meeting of the Institute is to be held from the 18th to the "25th of September. There will be a special train from New York City to Arizona and return, to take members and guests of the Institute to the meeting., The Committee in charge consists of Walter Douglas, Chairman, Cleveland E. Dodge, John C. Greenway, Arthur S. Dwight and Julius Kruttschnitt, Jr., and while the plans of this Committee are not complete, it may he announced that 'the train will be run with the requisite number of Pullman, dining and baggage cars to accommodate those who desire to go, which will accompany the party during the entire week of the Arizona Meeting as per the following program, including, of course, the visit to the Grand Canyon. It is especially desirable that the Committee should know, at as early a date as possible, the number of those who desire to make the trip; and those who desire special accommodations such as drawing rooms, state rooms, etc., are especially requested to communicate as soon as possible with the Secretary of the Institute, stating the number in their party.

Jan 6, 1916

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By E. T. Dumble

THE first specimens of this material which came under my notice, as found in the State of Texas, were sent to me by Mr. J. C. Melcher, of Fayette county, soon after the organization of the State Geological Survey. I wrote him concerning it, and had the locality and manner of occurrence described, but 1 had no opportunity to visit and examine the deposit until the present field-season. Later, specimens were collected by Dr. Penrose and myself on a trip made by boat down the Rio Grande, from Eagle Pass to Hidalgo, in June, 1889. At the time of collection I marked the substance "Albertite," doubtfully, but, on examination, it proved to be nearer Grahamite. The geological horizon of the two occurrences is Tertiary. The first locality mentioned is in the upper part of the beds called by us Fayette beds, and provisionally correlated with the Miocene, or Grand Gulf of Hilgard's Mississippi section, while the latter is in the lowest strata of the Eocene which are exposed on the Rio

Jan 1, 1893

By T. Sterry Hunt

THERE are about sixty bodies which chemists call elements ; the simplest forms of matter which they have been able to extract from the rocky crust of our earth, its waters, and its atmosphere. These substances are distributed in very unequal quantities, and in very different manners. As regards the frequency of these elements in nature, neglecting for the present those which constitute air and water, and confining ourselves to the solid matters of the earth's crust, there are a few which are exceedingly abundant, making up nine-tenths, if not ninety-five hundredths, of the rocks so far as known to us. The elements of which silica, alumina, lime, magnesia, potash, and soda are oxides, are very common, and occur almost everywhere. There are others which are much rarer, being found in comparatively small quantities. Many of these rarer elements are, however, of great importance in the economy of nature. Such are the common metals and other substances used in the arts, which occur in nature in quantities relatively very minute, but which have been collected by various agencies, and thus made available for the wants of man. It is chiefly of the well-known metals, iron, copper, silver, and gold, that I propose to speak to-night; but there are two other elements not classed among the metals, which I shall notice for the reason that their history is extremely important, and will, moreover, enable us to comprehend more clearly some points in that of the metals themselves. I speak of phosphorus and iodine. You all know the essential part which the former of these, com- * An address before the Polytechnic Association of the American Institute, during the meeting of the American Institute of Mining Engineers in New York. Printed in this volume by request of many members.

Jan 1, 1873

By AUDLEY H. STOW

I. INTRODUCTION. THE general drift of the discussion as to the relative merits of pressure- and exhaust-fans has resulted, if we may judge from the prevailing practice, largely in favor of the latter. The subject has been hitherto treated, however, with special reference to highly gaseous mines, the effect of the form of ventilation upon dust-explosions having been too little considered. Even in mines containing practically no gas, dust-explosions may occur; and if, as I believe, pressure-fans are to be preferred for their effect upon dust, it may be worth while to reopen the debate, and to challenge the advisability of exhaust-ventilation under certain conditions. There are several forms of colliery-ventilation, which may be described as follows: Plain or simple pressure-ventilation, in which the fan acts as a pressure-fan, and the movement of coal is unobstructed at the surface by doors or equivalent devices in drifts or shafts, the traveling and haulage thus being in the return-current. Plain exhaust-ventilation, in which the fan acts as an exhaust-fan, the movement of coal being likewise unobstructed at the surface, and the traveling and haulage being in the intake. Obstructed pressure-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the intake. Obstructed exhaust-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the return. The apparent advantages in running a fan "pressure" during working-hours, and " exhaust" between shifts, seem to justify the recognition of this combination as a standard form of ven-

Feb 1, 1909

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By John E. Murphy, Ernest L. Ohle

Hematite-magnetite ore bodies at Iron Mountain, Missouri, have produced nearly 9 million tons of iron ore concentrates since 1844. The ore minerals occur principally as open-space filling in fractured and brecciated andesite porphyry with very minor replacement of the wall rocks. The enclosing rocks are Precambrian in age and consist of a series of dacite, rhyolite, and andesite flows aggregating about 2000 feet in thickness. All of the ore is in andesite and the mineralization is Precambrian in age. The shape of the ore bodies, the breccia character of the ore, and the gangue mineralogy are believed to be unique. One of the two main ore bodies is crudely dome-shaped with a tendency for development of concentric mineralized shells; the other is an elongated lense in plan but hook-shaped in cross section. Both have strong linear elements striking northeast, east-west, or northwest. Various modes of origin for the structures and for the tension breccias have been suggested, but none is completely satisfactory. Hematite is the main ore mineral; magnetite is subordinate. Important gangue minerals are andradite, quartz, calcite, actinolite, apatite, epidote, and chlorite. Although some evidence favors injection of an iron-rich melt, other evidence suggests ore formation by a high temperature, water-rich solution.

Jan 1, 1968