Search Documents

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Lucas Breder Teixeira

O uso de ferramentas de simulação numérica para análise estrutural vem se expandindo nos últimos anos, sobretudo utilizando o método dos elementos finitos. Nesse trabalho são apresentados dois exemplos de otimização de projetos envolvendo componentes de mecanismos de válvula gaveta, realizados pela Magnesita Refratários S.A. Partindo da geometria inicial até o produto final, é analisado como o campo de tensões é adequado a valores admissíveis, conforme modificações de projeto são realizadas. Por fim, é demonstrada a importância desse tipo de estudo para alcançar maior confiabilidade e segurança em projetos mecânicos.

Aug 16, 2017

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By Samara Sâmid Aguiar Correia

A crescente necessidade por resultados de análises laboratoriais dentro das indústrias são cada vez mais exigentes em termos de tempo de resposta e precisão. Aliado a isso, a elevação do volume de minério de ferro exportado e o aumento da variabilidade desses produtos requerem processos cada vez mais rigorosos e tomados de decisões mais rápidas. Nesse contexto, os analisadores on-line têm um papel fundamental, pois atendem tais exigências, além de preservarem a segurança operacional. Este trabalho tem por objetivo mostrar o desenvolvimento da implantação de analisadores de umidade on line na descarga dos vagões da Vale no Terminal Ponta da Madeira. A metodologia utilizada na medição de umidade dos analisadores usa o princípio de transmissão de micro-ondas, que é a melhor tecnologia disponível no mercado para este fim. Dentre as etapas de implantação, que abrange desde a aquisição dos equipamentos até a avaliação dos controles e ajustes operacionais, é mostrado o período de cada etapa, os problemas encontrados e as soluções adotadas. Em suma, atualmente há medição de umidade on line na descarga deste site e está em fase de implantação a análise durante o carregamento do embarque para controle de processo.

Aug 1, 2018

By Tiago Silva Costa

Os tratamentos térmicos são um conjunto de operações que têm por objetivo modificar as propriedades dos aços e de outros materiais através de um conjunto de operações que incluem o aquecimento e o resfriamento em condições controladas. Os aços SAE J403 1045, SAE J403 1075 e DIN 100CrV2 são aplicados em diferentes setores industriais graças às diferentes propriedades que podem ser alcançadas através de tratamentos térmicos. Este trabalho visou caracterizar e descrever as fases formadas nos aços SAE J403 1045, SAE J403 1075 e DIN 100CrV2 após tratamentos térmicos de têmpera, normalização e recozimento pleno.

Aug 16, 2017

By Luiz Peixoto, Andrea Falcon

There are a few ways to impact the capacity of a reciprocating compressor, by altering suction and discharge pressure and recirculation. By reducing the pressure drop in the section before the compressor it is possible to provide a higher suction pressure and subsequently achieve a higher compressor flow rate. The increase in the suction pressure while maintaining the discharge pressure reduced the demanded compressor Head. When considering oxygen compressors it is necessary to cautiously evaluate the safety norms and parameters due to the risk of explosions and fires due to high oxygen velocity.

Oct 3, 2019

By Pedro Antunes Amaral

Currently there is a constant and essential concern of preserving nature. Over the years the concern with the environment is increasing, new environmental laws are emerging and being applied more rigorously and consequently emerge economic needs and mineral processing practices and other materials. In this sense briquetting becomes an alternative to fine particles agglomeration by means of pressure and or temperature, with the aid or not of a binder, which allows to get a product not only compressed, which presents shape, size, and adequate mechanical properties. The reduction in volume of the material in some cases (beyond the technological benefits) also allows fine materials can be transported and stored more economically, safely and effectively. The production of coke is greater as the content of better coking coal is, thus he low capacity coking coal is not much used in coke ovens. This research aims to demonstrate that briquetting of mineral coals with low coking coal capacity is possible, additionally allows increased coke production, obtaining then a better yield of coke. Basically they take advantage of low price of no coking coals without changing the quality of the coke produced. Anyway, briquetting became a smart alternative to aggregate values, economy and care for the environment.

Oct 30, 2017

By Flávio Beneduce Neto

As trincas a quente ou de solidificação em peças micro-fundidas em superligas a base de níquel podem ser um item importante no índice de perdas em componentes específicos. O aparecimento desse defeito está ligado fundamentalmente à quantidade de líquido interdentrítico nos últimos estágios da solidificação e, principalmente, ligado à composição química desse líquido. Há duas ligas amplamente utilizadas na produção de rotores para turbo-compressores ou turbinas para a geração de energia: o Inconel 713C e o Inconel 713LC. A diferença entre estas duas ligas é essencialmente o teor de carbono. Curiosamente, a liga LC tem uma maior tendência ao aparecimento de trincas de solidificação. O presente trabalho procura identificar as diferenças de comportamento na solidificação dessas duas ligas através da termodinâmica computacional e ligar essas diferenças no aparecimento das trincas. Os resultados indicaram que os teores de Zr e Nb do líquido remanescente da solidificação são muito superiores na liga LC causados pelo atraso na precipitação dos carbonetos tipo MC nessa região que deve ser a fase que aumenta a resistência mecânica da área. O correto balanceamento da composição química da liga em relação aos elementos citados permitiu que o índice de perdas por trincas de solidificação caísse para níveis próximos a zero.

Aug 8, 2018

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Jônatas Venancio Barbosa, Dagoberto Brandão Santos, Túlio Magno Füzessy de Melo

In this work, the mechanical and metallurgical behavior of titanium added ultra-low carbon (ULC-Ti) steel under hot and warm working conditions was studied by means of dilatometer compression tests. Double compression schedules were performed at temperatures between 700°C and 1000°C, inter-pass times of 0.5-100 s, and deformations of 0.5 and 0.3 in the first and second stages, respectively, with strain rate of 1 s-1. The analysis of the flow curves obtained allowed the evaluation of the softening characteristics of the steel. The softening and microstructure features indicate different restoration mechanisms depending on the temperature range. Static recrystallization with rapid microstructure restoration is observed at temperatures within the austenitic and intercritical field. Strain induced boundary motion and recovery mechanisms apparently control the restoration process in the ferrite region. In general, flow stress curves showed dynamic recovery behavior. Only the deformation in the intercritical region produced a peak in the flow stress curves. Isothermal holding tests associated with single hit compression indicated the presence of dynamic strain induced transformation, accelerating the softening kinetics at the intercritical region.

Oct 1, 2019

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By Thorsten Müller

In order to increase the production of Advanced High Strength Steel (AHSS) as well as to fulfill the growing expectations of various industries served, steelmakers must have wide- ranging know-how in terms of plant technology, operation, processes, quality control and, last but not least, know-how for AHSS including certification procedures. MET/Con is highly focused on the production of coated AHSS with tensile strengths higher than 600 MPa. Common heating and cooling technologies are unable to handle high alloyed steel grades – pre-oxidation and rapid cooling technologies have been developed to face these new challenges. MET/CON and Drever International have the knowledge to produce newest steel grades with these technologies.

Jul 30, 2018

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Claude Gaspard, Stefan Wahlund, Daniel Cavalier

A point of great importance in the cold rolling process for automotive sheet is the cleanliness of the strip, particularly critical in case of batch annealing with no degreasing line or inefficient cleaning before continuous lines. In this specific cases, pollution of the strip surface could be prohibitive when rolling in the early stands of tandem mill with conventional forged work rolls as ground. The strip cleanliness strongly deteriorates during rolling particularly with high roughness rolls: iron fines are generated at the strip surface due to friction and stick on the sheet. It is well known that chrome plating on ground forged rolls in the early stands improve the strip cleanliness. This paper summarizes the results of 3D surface roughness topography studies on forged work rolls, with and without chrome plating, combined with sheet cleanliness measurement during rolling. It shows that a well determined topography has to be obtained on the work rolls used in early stands in order to roll in the mixed lubrication regime, as described by the Stribeck curve, minimizing the friction coefficient and therefore optimizing the cleanliness of the rolled sheet. The main roll roughness parameters to take into account for that purpose are the roughness level Sa, and even more, the Kurtosis parameters Sk, Spk, Svk and Ssk. The ideal surface morphology promotes deep valleys to the detriment of peaks, leading to a roll surface capable of retaining/trapping oil in the valleys, while peaks are minimized, thus reducing the friction in the roll bite and the amount of iron fines produced. To achieve this objective, new grinding wheel technologies are currently developed, in dialogue with wheel manufacturers, to create such ideal morphology of roughness well adapted to HSS forged rolls.

Oct 1, 2019

By Carolina Sartori Marzullo

Apresenta-se a metodologia e sistemática para gestão da capacitação como ferramenta para aumento da competitividade e ganho de resultados do negócio num contexto crítico para o segmento.

Aug 16, 2017

By Rene Grabowski

Optimization of workflows and intelligent stock management; Slab stacking improvement by automated transport orders; and System automatically registers any slab movements even in manual operation. Case story: Steel producer ArcelorMittal Eisenhüttenstadt GmbH in Germany uses Primetals Technologie’s new stock yard logistics system in its finishing department. An exact image of its slab storage at any times is given by the warehouse logistics system to the company. It not only enhances the composition of the stacks of slabs, but also automates recording of manual restacking operations. Therefore the solution improves workflows and simplifies stock control. Cycle times have also been reduced due to the fact that the slabs can be charged to reheating furnaces ahead of the rolling mill due to less restacking operations within the slab storage. The expandable, modular system is based on the Siemens Simatic IT and Primetals Technologies’ IT4METALS Logistics product platform. It provides a large number of organizational and commercial features in the form of sophisticated graphics and tabular evaluations. For example, it can show how many crane movements have been made per shift for any category of slab, so that the time and cost for each operation can be calculated accurately.

Aug 16, 2017

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018