Search Documents

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

Permitting, engineering and evaluation, detailed design and construction aspects of the Golden Cross goldmining project in New Zealand are briefly reviewed. The extremely lengthy and complicated governmental approval process together with the delaying tactics of opponents of the project are outlined and comment is made on aspects of the draft legislation proposed as part of the overhaul of New Zealand's resource management laws.

Jan 1, 1990

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By B Mohanty, M P. Roy, P K. Singh

"The measured response of residential structures is a critical indicator of troublesomeor potentially damaging ground vibrations. A study was conducted to evaluate theresponse of structures situated in the periphery of four open-pit coal mines in India. Although, most of the structures were at far-off distances from the present blasting sites, an attempt was made to document the response of structures to blast vibration for future applications to optimize the blast designs for the safety of the structures. The study involved a total 215 blasts, employing one-, two- and three-hole calibration study, and production blasts. The bench height varied from 7.5 m to 42 m, and boreholes loaded with emulsion and slurry explosives were 250, 260, 270 and 310 mm in diameter. The explosive detonated in a blast were between 300-198400 kg whereas in a delay it was 33-24800 kg. Up to 12 tri-axial vibration sensors were located in overburden along a linear array from 25 m to 6.5 km distance from the blasts. Altogether, 1512 blast vibration signatures were recorded. Production and specially fi red single-charge blasts allowed the determination of natural ground frequency. The fundamental frequency of the structures ranged between 3.13 to 10.6 Hz, the same as those of the ground vibrations. The amplifi cation of vibration in the structures was in the range of 1.6 to 5.6. The study details the interaction between ground vibrations and selected structures, and the means to reduce amplifi cation of vibrations in the structures and persistence of vibrations through improved blast design."

Jan 1, 2008

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By B. L. Eggers

This study investigates the application of computed order tracking with subsequent rotation domain averaging and statistical analysis, to the drag gearbox of a dragline used in a mining environment. Computed order tracking is a fault detection method developed to deal with the varying speed conditions often found in industry and has been proven effective in laboratory conditions. Its application to real situations, however, requires some adjustment to deal with issues such as inadequate speed data and the fact that the drag gear rotates in two directions. This provides a unique opportunity to observe the performance of the order tracking method in a bi-directional rotating environment, allowing an investigation of the relationships between the results obtained from each operating direction. A monitoring station was set up aboard the dragline and data was captured twice daily for a period spanning approximately one year. The data captured consisted of accelerometer and proximity sensor data. The key on the shaft triggers the proximity sensors, allowing speed and direction to be measured. The measured speed is interpolated by using various speed interpolation techniques. Then the interpolated speed is used to complete the order tracking procedure that resamples the vibration data with reference to the speed. The results indicate that computed order tracking can be successfully employed in real environments. Furthermore it is shown that the rotation direction that opens the gear-tooth crack gives a better indication of incipient failure. It is therefore important not to disregard either direction when monitoring rotating machinery of this kind.

Jan 1, 2007

By P. Oyanader

"In 2001, the Catholic University of Chile undertook a maintenance benchmarking study of six open pit copper mines having mill capacities varying between 18,000 t/d and 156,000 t/d, and collectively responsible for 58% of Chilean copper production. This paper describes the methodology used to conduct the study, as well as the overall results. Key performance indices were selected to measure the effectiveness, efficiency, and development of the maintenance process. Using a balanced scorecard philosophy, these indicators were divided into client satisfaction, financial, internal process, and learning and growth indices.Maintenance was found, on average, to be responsible for 44% of mine production costs. Percentage planned maintenance of equipment fleets was found to be low by world standards, averaging 35%, 56%, and 44%, respectively, for blasthole drill, shovel, and haul truck fleets. Fleet availabilities were found to be significantly influenced by the percentage of planned maintenance achieved, while maintenance cost per equipment was found to decrease non-linearly with increases in percentage planned maintenance. Investment in technical training (including planned maintenance practice) was found to be low by global standards. The paper concludes that fleet availability and maintenance costs in Chilean open pit operations could be considerably improved by improving and/or developing maintenance planning standards, and investing in training personnel in planned maintenance techniques"

Jan 1, 2005

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By Nicholas G. Theofilos

The only mining activity in Belize during 1976 involved the production of construction aggregates, which were used domestically. A comprehensive ordinance regulating mineral prospecting and mining was proposed during the year. Under the ordinance, which would supersede all grants and titles, ownership and control of all minerals except petroleum would be vested in the Government. Exxon Corp. entered into an agreement with three oil companies to achieve a majority interest in nine oil prospecting leases covering 1 million acres, mostly offshore Belize. The agreement was with Weatherford International Inc. which had 30% interest in the leases, Ajax Petroleum Co. with 40% interest, and Canadian Superior Oil Ltd, with 24% interest. A new entity, Esso Ventures Inc., was established to be responsible for conducting extensive geophysical operations and drilling an exploratory well offshore Belize.

Jan 1, 1980

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007