Search Documents

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By Anthony J. Konya, Calvin J. Konya

Mine sites and construction projects have faced problems with blasting a smooth back wall. This lead to safety concerns with slope stability and rock falls from the walls. Decades ago Dr. Calvin Konya began a special type of blasting called “Precision Presplitting”. This form of presplitting used relatively light loads based on the rock type being blasted. The explosive loads were estimated for each rock type and adjusted as blasting progressed. This current research project also determined a new equation for prediction of the ground vibration from one type of presplitting and compared it to vibration from production blasting.

Jan 1, 2016

By M. G. Zabetakis

This publication describes an investigation conducted by the Federal Bureau of Mines regarding the cause of an explosion of a dephlegmator or fractionating column at the Cities Service Oil Company Refinery, Ponca City, Okla., January 22, 1959. The column was that used with the refinery's No.1 Dubbs Coker. The explosion caused the death of an employee of the refinery and resulted in extensive damage to the refinery and to nearby property. The Bureau's study of the explosion began January 26.

Jan 1, 1960

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it. With the arrival of the Spanish in the early 1700s, platinum was labelled a nuisance for the Spanish in their quest for alluvial gold because it concentrated with the gold and had to be removed by either extended amalgamation or by hand sorting. It was at this time that platinum received the root of its current name for the Spanish referred to it as platina del Pinto, platina being the somewhat derogatory diminutive of plata (silver). Pinto was a river in Colombia where the Spanish first distinguished it. The English eventually adopted ?platina? and it is only in recent times that the Latin name platinum has been accepted as the metal?s common English name. From its first introduction to European scientists in 1740, platinum was unappreciated because of its brittle nature and difficulty of working and as a result had little commercial value. Its ability to be dissolved in gold did lead to some counterfeiting of gold bullion and even to the debasement of gold currency.

Jan 1, 2000

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

Further evidence is presented as to the widespread occurrence of Thiobacillus ferrooxidans in nature in association with sulphide minerals. Leaching rates are discussed in terms of the effect of environmental parameters, particularly Eh and pH, on the bacterial process.The methods used to investigate leaching phenomena are described and the advantages and limitations of each method are discussed. A theoretical treatment of the bacterial leaching process is given which indicates that the optimum conditions arrived at by traditional methods are compatible with those deduced from consideration of the mathematics of continuous culture and thermodynamics

Jan 1, 1968

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By P. Chaddock

The Thompson Mill has a capacity of 15,000 T ID of ore and produces two grades of nickel concentrate, copper concentrate and occasionally graphite concentrate. Up to July of 1985 we processed two distinct ore types: T-1 ore, averaging 2. 8% Ni and . 2% Cu and Pipe Open Pit ore, averaging . 8% Ni associated with peridotite and serpentine. Presently our ores from T-1 mine and Thompson Open Pit are of the same type and are processed together. (Figure 1)! n October, 1982, we decided to install an Outokumpu Courier 300 on-stream analyser on an initial 6 streams. The equipment was delivered to the mill on May 2, 1983 and the first analyses were generated by June 17th. The calibrations were 35% complete by the mid-July summer shutdown and were completed in the fall. 1. 2 Analyser Slurry Feed System:The key to successful on-stream analysis is delivery of the sample streams to the analyser.Our system uses pressure-thief sampling for collection. (Figure 2) Initially we used thief samplers modelled after the Outokumpu design, with turbulence bars upstream of the collection point. These units have been replaced with simple laterals as they have worn out. Our thief samplers are mounted vertically on pump discharges and we believe sufficient turbulence exists to ensure representative sampling.

Jan 1, 1987

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

By Jarek Jakubec

The new euphoria in diamond exploration brings with it a need to understand the challenges that new projects can face in different stages of the development and risks that the commercial outcomes from the new projects fall short of expectations. In many cases, the problems are related to a poor understanding of the technical risks and a failure to adequately address them during the course of investigation. Failure to evaluate all disciplines to the same level of certainty could lead to a situation where the important issues are only identified late in the project development, resulting in costly delays and financial difficulties. The diamond projects located in Canadian Arctic, with its challenging environmental, geographical, social, political and geological contexts are especially sensitive to the high variability of the outcome. This presentation highlights some of the technical aspects that could be the leading sources of risk in diamond projects and could ultimately result in inappropriate mine designs, reducing the economic outcome.

May 1, 2006

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By Stephan Buys, Dan Curry, Chris Rule

"The use of fine grinding (FG) in mineral processing is well established. The application of FG in the South African platinum industry is more recent and it’s use in the recovery of PGM’s from dormant tailings dams is unique. Anglo Platinum uses IsaMill FG technology at their Western Limb Tailings Retreatment project (WLTR) near Rustenburg in the North West Province of South Africa.In December 2003, Anglo Platinum commissioned the first purpose built tailings re-treatment facility for PGM recovery in South Africa. The concentrator re-treats Merensky ore tailings from concentrators that operated early last century. The WLTR facility takes advantage of modern technology, such as FG, to economically recover PGM’s from material historically considered as waste. The WLTR concentrator has a capacity of 4.8 Mtpa, and has been designed to easily expand to 10.8 Mtpa. The flow sheet includes recovery of tailings by high pressure water monitoring, ball milling, rougher flotation, rougher concentrate regrinding and cleaner /recleaner flotation.The rougher concentrate is reground in an IsaMill, which is a stirred mill that operates with inert silica sand grinding media. For this project, Anglo Platinum required a stirred mill of a unit size not previously available. Xstrata Technology and Anglo Platinum collaboratively developed the largest wet, fine grinding mill available; the M10,000, 2.6 MW IsaMill.The use of IsaMill technology was enabling for the WLTR project, as it allowed smeltable concentrate grades to be produced from the oxidised, slow floating tailings. The economics and practicality of fine grinding has fundamentally changed with the M10,000 IsaMill. Flotation is transformed by high intensity attritioning in the inert media environment, and the narrow size distribution of product in open circuit configuration. The use of conventional steel media grinding to improve fine particle flotation is limited due to the oxidation of liberated mineral surfaces inherent in these environments."

Jan 1, 2005

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005