Search Documents

By R. B. Fisher

This report gives the results of mineralogical research on the Nicaro (Cuba) nickel ores and plant products. These studies were made under a cooperative agreement with the General Services Administration (GSA) of the U. S. Government. The purpose of the investigation was to obtain fundamental data that would be useful to other GSA contractors concerned with the Nicaro ores in their research on reduction roasting, leaching, and other phases of the project; and to the metallurgical staff of the Nicaro plant in Cuba. The overall objective of the combined research was to provide data to accomplish metallurgical improvement in the operations of the U.S. Government-owned plant at Nicaro, Oriente Province, Cuba. Particular emphasis is placed on improving the recovery of nickel from the ores and on the possibility of recovering other valuable constituents, especially cobalt. This study presents the physical and chemical characteristics, mineral associations, differential thermal analyses in controlled atmospheres, and X-ray studies of the ores and plant products. The nickel ores, serpentine and laterite, were from the Ramona-Lama Mulo and Ramona ore deposits. Serpentine ore consisted of serpentine-group minerals, basic iron oxide, magnetic iron oxides, chromite, olivine, enstatite, anthophyllite, cryptocrystalline quartz, wad, and a trace of calcite. This ore contained 1.6 percent nickel, 0.05 percent cobalt, 0.86 percent chromium, and 17.4 percent iron. Laterite are was composed principally of goethite with some altered serpentine, quartz, chromite, wad, magnetite, maghemite, and hematite. It carried 1.3 percent nickel, 0.11 percent cobalt, 1.9 percent chromium, and 48.4 percent iron.

Jan 1, 1959

By Monger N. R

Factors leading to the decision to use Joy Continuous Miners for pillar extraction in the Burwood Colliery are outlined. A detailed description is given of the Joy 1-CM-2 Continuous Miner, including the power supply to the machine, and the method of cutting coalfrom a face. Modifications found necessary in practice are dealt with.The Joy 10 S.C. shuttle car used in conjunction with the Miner, and alterations made to this unit, are then described, together with Ancillary units for the whole installation such as transformers, motor generator set, air compressor,_ cables for power supply and water supply for dust suppression.Special arrangements were necessary to transport the Miner and Shuttle Cars through the tunnel to the Victoria Tunnel seam, and the method of overcoming the transport difficulties is discussed. Manning of the Continuous Miner unit, and final preparation andsubsequent working of the pillars is outlined. Special attention must be given to maintenance of the machines.It is concluded that the combination of Joy Continuous Miner and Shuttle Car is an excellent method for removing pillars in the Burwood Colliery.INTRODUCTIONThis paper deals with the Burwood Colliery in the RH.P. Group in which some units are engaged in the mechanical extraction of pillars with Joy Continuous Miners.In 1941, an amendment to the Coal Mines Regulation Act of N.S.W. forbade the extraction of pillars by mechanical means unless with the express permission of the Minister for Mines. As this permission was not forthcoming, no mechanical extraction of pillars took place in Australia until 1954 As it was doubtful during most of this period whether mechanical extraction would ever come about, coal generally was won with a view to maximum extraction in the first workings, thus giving rise to centre gannon bord panels and 45° angle cut throughs as shown in Fig. 1.

Jan 1, 1957

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By David M. Spatz

The way people interact, collaborate, learn and improve can have a profound impact on a company’s efficiency, performance, productivity and return on investment. This is the motive behind corporate efforts today to replace the traditional hierarchical structure with team-oriented organization. The increased importance of communication and collaboration during the past 20 years has been propelled by rapid advances in technology and increased availability of information. Companies must take advantage of the information that is required for competitive performance and for the continued production of quality products. So it is essential that outstanding communication, cooperation and collaboration take place among multidisciplinary specialists assigned to work together to solve common problems and achieve common goals. Companies are searching for ways to increase knowledge transfer and learning, particularly among people who work on related topics. This will improve efficiency and quality and reduce redundancy and costs.

Jan 1, 2000

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By L. Lehasa

The purpose of the project was to investigate the challenges faced by Khutala Colliery pertaining to underground road construction and maintenance. Furthermore the influence of these challenges on productivity and safety requirements were taken into consideration. The operating standards required for the construction and maintenance of the 2 seam road transport infrastructure was investigated, together with reasons why the standards of operating procedure are not met. The Code of Practice put in place by Khutala Colliery was used to view the standard operating procedures. Leading practices on underground road construction were researched. The project aims to discover the gaps that Khutala Colliery must bridge to implement enhanced practices with regards to underground road construction. During the period of study, observations were carried out to determine whether the road construction standards of operating procedure were being adhered to at all times for both road construction and road maintenance. Khutala Colliery has put in place a traffic management plan, which includes safety practices and work policies that must be adhered to while travelling on underground transport roads.

Jan 1, 2012

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By C. W. Morris

This study was performed for the U.S. Bureau of Mines. An existing computer simulation of a dragline was modified to simulate a dragline dumping into the hopper portion of a cross-pit conveyor system. This revised computer model was then used to study four proposed cross-pit conveyor systems. Parameters such as dragline position, hopper position, and digging procedure were varied to maximize the dragline production. This performance was compared with the conventional side-casting spoil method. I t was concluded that the cross-pit conveyor systems were competitive with the conventional side-casting technique.

Jan 1, 1977

By T J. Sprott, Associates

A number of people have expressed concern, understandably, that if mining operations take place in the Coromandel, the flows of mineralised ground water which exist will be intercepted. This water in many cases contains toxic metals including mercury, arsenic and lead and it is thought that if this water is allowed to enter streams or the waters of the Hauraki Gulf, it could endanger natural marine life and possibly established fisheries. This paper seeks to explain in simple terms the geology and the process of deposition of the various mineral deposits in the ground, the chemistry of the reactions between these minerals and the rain water falling on the ground, the hydrology and behaviour of this mineralised groundwater as it moves through the ground until it eventually enters the sea.

Jan 1, 1981

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006

By Xiangxi Wu

Longwall and continuous mining are prevalent methods employed by Chinese underground coal operations. The main ground control challenges include roof skin deformation, roof collapse, and outbursts of coal, gas, and water. Microseismic monitoring provides valuable information on rockmass behavior and fracture propagation caused by stress redistribution, active geological structures, or gas build up within the coal strata and the surrounding rockmass. Collecting and assessing seismic data has proven to be an instructive tool for engineers to better assess ground conditions and mitigate seismic hazards associated with mining. The development of intrinsically safe and explosion proof certified seismic monitoring equipment has revolutionized China?s underground coal mines. The use of this technology allows for the optimization of gas drainage at an increased rate of two at a 50% higher purity without any increase in drilling costs. Microseismic monitoring can also be used in identifying seismically active faults and shear zones. This information can be used to assess and revise mining strategies to improve safety and ground stability.

Jan 1, 2012

By S. J. Swart

This paper discusses the principles and application of risk assessment and management as the basis for environmental management within the mining industry. Unlike in other industries, mines are required to obtain closure certificates in terms of section12 of the Minerals Act, which should ultimately release them from further environmental responsibilities. It is emphasized that the concept of environmental risk assessment and management, when applied correctly will mean that the mine will be identifying and managing environmental issues beyond those set by current legal requirements and management strategies. The focus shifts from conventional minimum legal compliance management to management of real environmental risks. The advantage of this approach is that the perceived ?shifting of legal and management goal posts? due to changing environmental laws or management principles, will not influence or dictate the mine?s short or long-term management objectives or actions, mine closure funds can be more accurately determined and mine closure should become a relatively simple procedure. The risk assessment approach has been applied to the planning of mine closure at Iscor?s Durban Navigation Collieries (Durnacol) in Kwa-Zulu Natal and certain key risk issues such as the long-term risk of water pollution from coal discard dumps have already progressed to fully quantitative risk assessment. This paper will discuss the process, which has been followed to date, with particular emphasis on the most recent phase, namely quantitative risk assessment and management of pollution from coal discard dumps. It is believed that the approach that is being pioneered at Durnacol and which overcomes some of the more obvious deficiencies of both the EMPR and the traditional IEM process will ultimately serve as the model for all responsible mines in South Africa. It is also believed that this approach will enable the authorities to issue closure certificates with the confidence that there will be no unforeseen surprises in the years after closure.

Jan 1, 1998

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

The discussion in this paper centres on examples of mining that are drawn mainly from the coal mining industry. The intention is to review the opportunities that exist for incorporating environmental planning into mining industry practice in New Zealand. The coal mining examples serve to make some general points which have some application for many types of mining.

Jan 1, 1981

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013