Search Documents

By Caithness SJ, Heape JMT

Following the discovery by CRA of gold at Mt Kare, and the subsequent 1988-90 gold rush, mechanised mining of the alluvial resource is now being carried by a company jointly owned by CRA (51%) and landowners of the area (49%). Mining is currently being carried out using small gravity processing plants fed by hydraulic excavators. Use of hydraulic mining techniques will be limited to over- coming difficulties related to the high clay content of the material and the soft nature of the bedrock. Current resource estimates suggest that the alluvials will have a mining life of three to four years. During this time, exploration of the hydrothermal gold mineralisation at Mt Kare will be carried out by a wholly-owned company of CRA. It is hoped that this will lead to establishment of an economic primary gold resource.

Jan 1, 1991

By Wilson D, Kirkland J

Compressed air energy storage (CAES) uses low cost off-peak energy to compress air and pump it into pressurised underground storage. Expanding the air through a modified form of gas turbine generates electrical energy when required. While generating power, a CAES station consumes approximately one-third of the gas required for the equivalent installed capacity of a conventional gas turbine. Air can be stored in underground rock caverns, caverns in salt domes, or in aquifers. Existing CAES power stations use caverns mined out of salt domes. Aquifer storage for CAES has been proposed, but not yet implemented. The groundwater in the aquifer would be displaced during air injection and when required the air would be extracted using the natural hydro-static pressure. Victoria has no salt domes, but has aquifers onshore in the Gippsland Basin with geological dome structures of suitable depth, discovery pressure, porosity, permeability and caprock for CAES development. Field tests costing several million dollars would be required to prove the suitability. The most suitable aquifer is near Seaspray, where several dome structures exist. The aquifer, comprising of coarse sands capped by coal and mudstone, is some 600 metres deep with a hydrostatic pressure of 6.3 MPa. Computer simulation of injection and extraction of air from the aquifer under various combinations of horizontal and vertical wells, permeability and tubing head pressures indicated the largest aquifer structure had the capacity to sustain a 300 MW station. A well field comprising of 24 directionally driven wells with a horizontal exposure to the aquifer would achieve the air flow rates required. Using plant similar to that recently installed at McIntosh Alabama USA, would mean high capital costs compared to standard gas turbine plant. However, a review of modem gas turbines indicated that they could be easily and economically adaptated to CAES duty. Adapting a 120 MW gas turbine would give 344 MW output. A separate air compression plant would be used. Economic evaluations indicate that, for gas prices above $1.95 per GJ, a 344 MW CAES plant is more economic for intermediate/reserve load duty than simple cycle gas turbines.

Jan 1, 1992

By M. T. Ansari

"This article explains the ways in which investment on mining infrastructure is a geopolitical issue. It discusses the effect of installing sufficient infra structure to get the product to the world market, and argues that there is a risk involved in depending on traditional suppliers who wish to invest in the infrastructure. It explains how to make a distinction between dedicated purpose infrastructure and general use infrastructure by examining the positions of the main actors in mining projects. It argues that these positions can not be understood as analogous to projects in developed countries. To conclude, infrastructure is a crucial link in the supply chain to market but the relative size of such projects in relation to the economy means that investors decisions in developing countries have quite different implications from those in developed countries."

Jan 1, 2011

By Y Sha

During the last two decades, China has expanded its iron and steel industry very quickly, from less than 100 Mt/a steel production to over 700 Mt/a. It caused big increases in both domestic iron ore production and imported iron ore quantities year by year. The mode of iron ore supply has changed from almost all domestic supply to major tonnes of imported ore plus domestic ore supply. Over 200 blast furnaces with volumes larger than 1000 m3 each have been built and put into operation. Sinter machines have been enlarged quickly. There are now 135 sinter machines with =200 m2 sintering area each. Pellet production increased from 11.94 Mt in 1999 to 210 Mt in 2011, resulting from rapidly increasing domestic concentrate supply and rapid development of the grate-kiln process. The typical ferrous burden constitution is high basicity sinter plus pellets plus lump. The pellet proportion increased and the sinter proportion decreased gradually. A lot of technical improvements, like deep bed sintering, sintering with a high ratio of limonite, composite sintering, pellet process optimisation, a high ratio of hematite in pelletisation, blast furnace operation with low-grade ferrous burdens and hazardous element control, etc have been made to enhance iron burden quality and to reduce hot metal cost. Chinese iron and steel production is expected to increase slightly in the next few years. Its overcapacity should be controlled effectively. Given the variations of iron ore supply, pellet production will keep progressing in terms of production scale and pellet quality, the sintering process will be improved further by various measures to utilise different ores efficiently, and ferrous burden constitution will be optimised continuously to realise the lowest cost of hot metal production.CITATION:Sha, Y and Wang, Z, 2013. The Chinese iron and steel industry response to the challenges of iron ore supply, in Proceedings Iron Ore 2013 , pp 7-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By Jian Li

Developing the Generation IV nuclear reactor is an international collaborative effort. One of the most promising Gen IV nuclear reactor designs is the supercritical water (SCW) concept, in which the water coolant runs at about 625 oC at the outlet. Under this temperature and high pressure condition, the cooling water is at supercritical state, which poses significant demand for both in-core and out of core materials. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR conditions. Corrosion experiments per-formed under SCW condition yield various kind of corrosion modes, some are very challenging to characterize using conventional techniques. A combination of various advanced characterization techniques proofed to be essential to understand the root cause of materials? degradation.

Jan 1, 2010

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

The morning session opened at 9:00 a.m. and was presided over by Mr. Don Ross, Manager of Mines, Kaiser Steel Corporation,- Sunnyside, Utah. The first speaker was Mr. S. W. Zanolli, Partner in Law Firm of Webster and Kilcullen, Washington, D.C. Mr. Zanolli was born and raised in a coal mining community of Fredericktown, Washington County, Pennsylvania. He was educated at Washington and Jefferson College and graduate schools of the University of Pittsburgh. He served as an infantry officer in the European Theatre of operations during World War 11. He worked as' a handloader at Vesta No. 5 Mine of Jones & Laughlin during summers while attending Washington and Jefferson College. He worked at a variety of production jobs at No. 7 Mine. of Island Creek Coal Co. of Holden, West Virginia. Assigned to a variety of industrial relations assignments at Island Creek Coal' Company during 1949-51, attaining position of Supervisor of Personnel and Labor Relations. Served in many industrial relations assignments at U.S. Steel Corp. headquarters during 1953.-1967, attaining a position of Personnel Director-Heavy Products Operations. In January, 1968" he became a member of the Bituminous Coal Operators Association-as Executive Vice President. This past year he went back to practicing law and is a member of the Law Firm of Webster and Kilcullen, Washington, D.C. He is married and has five children.

Jan 1, 1973

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By C. G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX/EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to copper concentrates and ores will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of chalcopyrite concentrate treatment with this unique industrially proven process will be delineated.

Jan 1, 2001

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

By Kristen E. Coose

Concrete is a mixture of a fine aggregate (sand), a coarse aggregate (gravel), cement, and water. Cement itself is the most expensive of the ingredients but generally amounts to only about 10% of the concrete mixture. Cement raw materials include calcium, alumina, iron oxide, silica, and gypsum. They are heated and chemically changed into clinker "minerals," which are then ground and shipped as cement. Each of the four main clinker minerals-tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminoferrite-impart specific strength and compositional properties to the final concrete product. During hydration of the cement, chemical changes produce new minerals that include calcium silicate hydrate gel (C-S-H, the main constituent of hydrated cement paste), calcium hydroxide, and calcium, sodium, potassium, and sulfate ions, among others. Two main reactions can occur that may be deleterious to concrete. Normal cement pore solutions, in a hydrated cement, contain sodium hydroxide and potassium hydroxide. If these alkali concentrations are too high, they can react with the siliceous aggregate (alkali-silica reaction, or ASR) to form an alkali-rich calcium silicate hydrate gel (C-N+K-S-H), which, upon prolonged contact with water, can expand to crack the concrete. The other deleterious reaction occurs when the mineral ettringite (Ca6A12(S04)3OH12. 26H20) forms after the concrete is hardened (delayed ettringite formation) and cracks the concrete. Many of the concrete bridges and structures built in New Mexico in the past 20 years are in need of replacement due to deterioration. Many others constructed very early on in the century are still sound. By collecting and analyzing samples of both old and new concrete and good and bad concrete, we compared their differences on both a microscopic and macroscopic scale. Samples taken from concrete sidewalks, parking lots, drainage canals, spillways, and a railroad-trestle foundation have construction dates that range from 1923 to 1997. They were analyzed by electron microprobe and by petrographic microscopy. Cracks, air voids, and aggregate alteration were primary locations for investigation and analysis. Using the electron microprobe, ettringite was found in voids of most of the samples, both in good and bad concrete. This leads us to believe that ettringite formation is not causing distress in the concrete. There was one exception in which ettringite was found lining a crack. In this instance, ettringite may have the ability to further the cracking and cause distress. No alkali-silica gel was identified with the microprobe. Using the petrographic microscope in cross-polarized light, a light-brown material was observed that lined some of the air voids and cracks; however, exact mineralogic identifications were not made. Although many instances of chalcedony and other deleterious quartz phases were found, no clear evidence of ASR-gel deterioration was present in our samples using these methods. However, positive identification of the ASR gel was made on an in-place concrete near one of our sample sites and in several sample cores using a newly developed chemical test for the soluble potassium ions associated with the gel. The chemical used in this test is sodium cobaltinitrite, Na3Co(NO2)6.

Jan 1, 1999

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Lester G. Morrell

AGAIN in 1963, as in nearly every year since 1946, the Canadian mineral industry has established a new national record in value of mineral production. The 1963 estimated total value of $2,976 million is 5 percent higher than the 1962 value of $2,845 million.2 As in previous years, metals made up more than half the value of total production. For selected years since 1949 the category percentages and total value are as follows: [ ] Crude petroleum, Canada's most valuable mineral product, accounted for 21 percent of the total value of minerals in 1963. In descending order came nickel 12 percent, iron ore 10 percent, copper 10 percent, gold 5 percent, and uranium 5 percent. Asbestos accounted for 5 percent, sand and gravel 4 percent, and cement 4 percent. The complete list of Canada's mineral products includes more than 50 basic commodities.

Jan 1, 1964