Search Documents

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By Morgan W. M

It is not the primary object of this paper to treat with the scheme of prospecting in detail, but it is considered that a brief description of the broad lines is necessary so that the significance of the points to be discussed later may be appreciated.The finding of payable gold reefs on the Bendigo field resolves itself into a two-fold problem, firstly the location of quartz bodies, and secondly the location of gold shoots in such bodies. The country rock of the field has been folded and faulted, and the occurrence of known reefs is associated with the fold axes and the faulting. The "lines" of the field are the anticlinal axes, and practically all known reefs are at or near centre country. Very little work has been done on the synclines, which may have some potential value.Quartz has been introduced along the fracture systems, and gives rise to the three main types of reef met with on the field, namely, the "back," which is similar to a bedded quartz reef and is formed along a bedding plane fault; the "saddle," which forms at the crest of the anticline and has the typical shape from which it takes its name; and "spurs," which are irregular masses of quartz, making off reefs of the first two types.As the fracturing throughout the field is widespread and fairly intense, the first problem, that of finqing quartz, is comparatively simple, and any regular system of blocking out the ground will be productive of quartz bodies.*Field Superintendent, Bendigo Mines Ltd. Assistant Field Superintendent, Bendigo Mines Ltd.

Jan 1, 1936

By Kelly E. G

NZ Steel's flushing slag typically contains 1.2 per cent V203. Extraction of vanadium from powdered slag using a salt (NaCI or Na2CO3) roast/leach process was investigated. With NaCl, optimum extraction conditions were a charge containing 10 per cent NaCI, roasting in air at 875°C for 4 hours, followed by leaching in dilute H2SO4. Extractions were typically 30-50 per cent. NaCI roasting did not chemically attack the slag; the phase transformations that occurred were due to high temperature oxidation. Slag particle size had a significant effect on extraction.Optimum conditions for extracting vanadium by Na2C03 roasting were 20 per cent Na2CO3 in the charge and roasting in air for 3-4 hours at 850-875°C followed by water leaching.Na2CO3 roasting involved chemical attack that resulted in the formation of perovskite (CaTiO3) and carnegieite (NaAISiO4).The extent of vanadium extraction depended on the amount of Na2CO3 added and the original slag SiO2 content.Compared to the separate roasting treatments, simultaneous treatment with NaCI and Na2CO3 gave lower vanadium extraction, while requiring considerably higher roasting times and temperatures.

Jan 1, 1982

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Adrián Del Carpio

Desde 1995 la planta de Lixiviación de Toquepala desarrolló un sistema de control automático para los procesos de extracción por solventes y electrodepositación. Sin embargo, con el desarrollo de la tecnología y las nuevas versiones de control, dicha plataforma se tornó arcaica. En ese sentido, el presente texto señala la modernización de los sistemas relacionados con el control y supervisión de las áreas de extracción por solventes, depositación electrolítica y áreas auxiliares. Como consecuencia de ello, se incrementó la operatividad, disponibilidad y fiabilidad con cero paradas por perturbaciones eléctricas, así como redujo el tiempo utilizado para el diagnóstico y solución de problemas.

Sep 12, 2011

The problems of using comparatively simple x-ray diffraction equipment for quantitative analysis are examined. Internal standard and direct calibration procedures based upon the measurement of integrated diffraction energy (diffractometer peak area) have been developed for the determination of quartz in Broken Hill dusts. By these methods an accuracy of ± 10 per cent of the true value can be obtained and this can be improved to ±2 1/2 per cent by statistical methods if necessary.Rapid analysis for the components quartz, muscovite, rhodonite, galena, fluorite, sphalerite, calcite, and garnet has been developed by adaptation of direct calibration procedures and use of maximum diffraction energies (diffractometer peak height). Until more is know!) about the pathological effects of multi-component dusts of the Broken Hill type it seems undesirable to fix theIr allowable concentrations in terms of the quartz content.

Jan 1, 1968

By J Parr, P Ashworth, S Johns, C Yeats, A Littleboy

The ocean floor is increasingly being discussed in terms of its resource potential. New discoveries, improved knowledge and access to unexplored areas of the deep sea and continental shelf are some factors contributing to a renewed interest in the seafloor exploration and mining industry. The industry has been referred to as the ænext minerals frontierÆ. To date, much of the research has focused on proving economic and technical viability of the industry, with environmental issues addressed locally. However, there is limited research internationally, and none known in Australia that considers the social viability of the industry, addressing issues such as regulatory contexts, international precedence and public acceptability. Does the nascent seafloor exploration and mining industry have a social license to operate? Does it have support amongst the wider community? If not, why not? The Wealth from Oceans National Research Flagship explored these questions by scoping the social issues that would surround an expansion. Two desktop studies provide insight into the current level of activity in seafloor exploration and mining, recent developments and the regulatory regimes on which the industry is based. One study focused on the situation in Australia, while the other was internationally focused. A series of workshops were held with key stakeholders from government agencies, industry and other interested parties, such as environmental groups and the fisheries industry. These workshops identified and explored the different stakeholdersÆ perceptions of the benefits, concerns, opportunities and key questions associated with an expansion of the seafloor mining industry. The desktop studies revealed that Australia is one of only a few countries with legislation specific to seafloor exploration and mining. Nevertheless, barriers to licence approval exist because of lack of precedent in applying this legislation. Consequently, the decision process can be vulnerable to political issues and subjective judgements. The outcomes from the stakeholder workshops suggest this inconsistency may be influenced by the high levels of concern and uncertainty over environmental impacts. Uncertainty over environmental impacts can influence the acceptability of an environmental impact assessment (EIA) and also mean the perception of risk is variable. Overall, this research suggests that the future of the seafloor exploration and mining industry will be highly dependent on AustraliaÆs ability to:improve the knowledge-base underpinning the regulatory regime,generate open and transparent communications between stakeholders, andimprove the understanding of policy and regulatory processes.

Jan 1, 2008

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

A rotating disc of precipitant zinc in a single stage flow reactor was used to study the effects of deposit mass on the reaction kinetics of copper cementing on to zinc from dilute aqueous solutions.The reaction rate is controlled by external mass transport and the mass transfer coefficient (relative to the original precipitant area) is dependent on the quantity of deposit present. For deposit masses up to about 0·3 mg/cm2 the mass transfer coefficient (first order rate constant) is that expected for the counter-diffusion of reactant and product cations through a laminar boundary layer to a smooth rotating disc. For depositmasses from 0·3 mg/cm2 to about 5 mg/cm2, the mass transfer coefficient increases significantly with deposit mass. For deposit masses greater than 5 mg/cm2 and at least up to 12 mg/cm2, the mass transfer coefficient has again a constant value which is some four to seven times the initial ("deposit free") value. The rate constant for the entire range of deposit masses studied (0 to 12 mg/cm2 ) can be expressed empirically as a cumulative normal distribution of the logarithm of the deposit mass.The enhancement in the mass transfer coefficient for deposit masses greater than 5 mg/cm2 relative to the initial mass transfer coefficient depends on the local operating conditions and increases with increasing disc rotational speed. This enhancement is, however, independent of the previous history of reaction rates.

Jan 1, 1973

By Efrén Peña Pino

El presente texto señala la aplicación del sistema SAP en la minería subterránea de Minsur. Este sistema operativo maneja las propiedades y procesos de la Sociedad Minsur, el cual cuenta con tres Centros, dos de los cuales son operativos (San Rafael y Pisco) al margen de la central de administración (Lima) y permite la planificación de todos los recursos de la empresa de manera integral, evitando imprevistos y una mejora de decisiones.

Jul 31, 2003

The reconstruction of the world after the present war must inevitably be profoundly influenced by the rise and progress of New China.The principle of Chinese mathrity has been admitted by Great Britain and the United States by their abjuration of extra-territorial tights, and by the withdrawal of the Maritime Customs Administration. The United States admits equality by her declaration that Chinese are eligible for American citizenship, and the reaction to this will be swift enmity to such peoples as may impose humiliating restrictions upon Chinese citizens.Finally, the decisions of the Moscow Conference and the recent meeting of National leaders in Cairo give partnership rights to this new State in post-war reconstruction, and open the way for a rapid realization of her destiny.It seems certain that China, if so she wills, can become, within a generation or so, one of the considerable forces of the world. The toad she wiII follow will be lighted by her own inherent and intrinsic genius. Her speed of progress can no longer be forcibly influenced by other nations and the attitude towards her of somewhat contemptuous patronage hitherto adopted by the European communities bordering the Pacific Ocean must be radically modified.It is doubtful whether the European will ever reach full understanding of Chinese mentality. The Chinese "way of life" since the dawn of her civilization has been totally divergent from that of the European, but the enormous potential strength, due to the simplicity of their requirements and their steadfast industry, is a function of that "way of life." On the other hand the trend of reorganization must obviously be towards Western standards; and a wide knowledge of the potential strength of the Chinese is possible and will be essential in our post-war world. The following, necessarily inadequate, notes are therefore offered, as an indication of the obstacles to be overcome and the capacity of the Chinese executives and operatives to overcome them.For 'thirteen centuries the political and social structure of China proper (ie, excluding Mongolia, Manchuria and Tibet) has been rigidly shaped by the philosophy of Lao Tze and the ethics' of Confucius. This Taoism, which is described as the "way of harmony" with its three jewels of character, gentleness, economy and humility, advocates the minimum of social, economic and political organization and still gives the key to the Chinese character.The Mongol and Manchu conquests of the 12th and 17th centuries, respectively, could hardly be dignified with the name of war, but the superior intelligence and harder mentality of the unwarlike Chinese finally absorbed...

Jan 1, 1944

This paper briefly reviews the demise of professional mining education and training in NZ over the past ten years; compares it with the Australian experience; and discusses the immense success experienced by EXITO and the upsurge of competency based education and training we are currently experiencing in the mineral extraction and associated industries. It also looks to the development of a Bachelor in Mining Technology.

Jan 1, 2001

By J. H. Bain, D. C. Haigh, L. C. Parsons

Jan 1, 1964

A study of literature on the epidiorite dykes which transgress the Broken Hill lode and its wall rocks reveals a considerable diversity of thought regarding the time of emplacement of such dykes. In this paper it is deduced that the epidiorite dykes were formed at a late stage and were probably post-ore. Detailed mapping, sampling, and correlation of data from over 100 exposures substantiates this deduction. Physical disruption of the epidiorite dykes is indicated and some interaction of the epidiorite and ore at the time of intrusion is inferred.Further petrological study may confirm this.

Jan 1, 1968

By J. M. Benson

Titanium is an exciting structural material that can offer significant strength-to-weight advantages over currently used alloys. However, its Achilles? heel is its costly, energy-intensive production process that effectively eliminates it from competing with aluminium and high-strength steels, apart from critical applications where titanium forms only a small component of the total cost. Current attempts are being made to reduce the cost of titanium products and these recognize the importance of minimizing the costs over the total production chain. Powder metallurgy (PM) technologies play a crucial role within this, as the output of the existing and potential primary metal production methods is in the form of sponge or powder. By using PM, costly remelting and forming operations can then be avoided, except in the manufacture of large components. Metal injection moulding (MIM) is an effective process for producing complex net-shape components in large volumes from metal powders. Nevertheless, the commercial use of titanium powders in this process is still in its infancy. The only major supplier of feedstock utilizes a polyacetal-based binder. This gives good green strength but requires a catalytic nitric acid process to remove most of the binder prior to thermal treatment. As this involves additional and expensive equipment and is a potentially hazardous process, there is interest in finding an alternative binder system that can be debound either purely thermally or that involves a less hazardous, more environmentally friendly solvent. This paper describes the use of capillary rheometry to characterize the influence of temperature and shear rates on the flow behaviour of potential binder systems for titanium MIM feedstock. Keywords Titanium, metal injection moulding, capillary rheology, feedstocks, powder loading.

Jan 1, 2011

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950