Search Documents

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By J. Nakayama

Construction of foundation piles or diaphragm walls through rocky or boulder containing formations has been long-standing difficulty. It has been widely understood that the down-the-hole hammer is the most capable mechanical means but is restricted in drilling diameter by the unavailability of drillhead sufficiently large diameter and the difficulty of disposal of cuttings. A great number of submersible motordrills have been used for the construction of cast-in-place piles and diaphragm walls and the reverse circulation system employed has demonstrated its advantage of the prompt removal of cuttings. The development of multi-head down-the-hole hammer drill combined with reverse circulation system presents a powerful engineering choice for those "hard-to-drill" ground formations. This paper will introduce the features of the system and some actual operation results in the foundation engineering through those hard rocky ground formation in some countries.

Jan 1, 1989

By K. K. Murray, D. G. Gelderland

"The pressure oxidation autoclave at the Goldcorp’s Red Lake Gold Mines (RLGM) was commissioned in 1991. Since commissioning, the circuit has been well maintained and its capacity increased to mechanical and gaseous oxygen limitations. With advances in available technology, opportunities to produce more sulphide concentrate and a changing business environment, an optimization project has been initiated at RLGM. A multi-phase approach has been developed to optimize both the operations and economics of the circuit. This paper describes the history and future of the autoclave circuit at RLGM.AcknowledmentsWe would like to thank the operations and maintenance staff at Red Lake Gold Mines for their support and openness of mind to enact changes to enhance the operation. We would also like to acknowledge the members of the integrated team from Red Lake maintence, metallurgy, operations and corporate technical services that did the hard work to push past the status quo in order to advance productivity.OpportunityThe Red Lake Gold Mines (RLGM) pressure oxidation (POx) circuit has been in operation for over 25 years processing the high sulphide content gold bearing minerals. Increased sulphide concentrate production from improved flotation recovery and increasing gold sulphide association at depth has led to the POx circuit becoming a throughput bottleneck. The opportunity exists to process increased tonnages of sulphide concentrates and increase gold production. In order to realize this value, it will be necessary to increase the throughput capacity of the POx circuit.BackgroundThe POx autoclave at the RLGM, commissioned in 1991, was Canada’s first gold autoclave. It was installed to replace the two-stage fluid bed roaster that was built when the Campbell mine and mill were constructed in the late Forties. The circuit was originally designed to process 12.5 t/d sulphide sulphur in about 50 t/d of Campbell flotation concentrate. Following the merger of the Campbell and Red Lake Mines in 2006, the POx circuit started processing flotation concentrate from both Campbell and Red Lake Mills. In recent years, the circuit has been processing about 18 t/d sulphide sulphur in 75-85 t/d flotation concentrate."

Jan 1, 2017

Maori economic development still remains an enigma to many people some 157 years after the signing of the Treaty of Waitangi. It has only been in the last decade as a result of increasing pressures from Maori to recognize and settle grievances arising from the Treaty and the resulting compensation issues that "mainstream" has begun to sit up and take notice. While Treaty settlements such as the Tainui, Ngai Tahu and Fisheries settlements have gained prominence as a source of economic potential for Maori, there are significant existing assets owned by Maori worth an estimated $4.6 billion that add an exciting new dimension to Maori contribution to New Zealand's enterprise economy.   Despite the fact that many claims have yet to be resolved, Maori are clearly shifting from grievance to development mode as evidenced by their focus on capacity building through education, strategic alliances nationally and internationally and the significant growth of nett asset worth of Maori interests in a number of industry sectors.   In essence, Maori provide a large un-tapped economic potential in New Zealand. The years of relative economic obscurity appear to have wetted their appetite for positive growth and economic independence. Given current trends, it would not be unrealistic to expect the asset base of Maori to double in value over the next decade and to see the emergence of Maori owned Corporates not only within the New Zealand economy but also trading actively in the global market place.

Jan 1, 1997

When the HSE Act was introduced in New Zealand in April 1993, one of the prime aims of the Government was to signal to the industry. The Government's recognition of the employer as the key person responsible for safety and health in the workplace and to actively encourage employers to self manage the health and safety function. Because of the significant change in the philosophy behind the new legislation, and because of the inherently conservative nature of the mining industry, it has taken some years for both the industry and the regulators to reach the stage of considering the framework in which a controlled degree of self management can proceed.   In this paper, some of the issues relating to the legitimacy of the process are considered, some of the questions raised in the minds of those charged with implementing the legislation are discussed, and the views of some eminent authors are examined.   The latter part of the paper focuses on a programme called the Reduced Site Surveillance Programme, which grew out of Goal 2 of the New Zealand Mining Inspection Group's 5-Year Strategic Plan. The programme is described in some detail, and the criteria applied at each stage of the programme is discussed. The paper concludes with the author's expectations of the longer term outcomes of the programme.

Jan 1, 1997

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Mohan K. Wali

Soil and vegetation development were studied on abandoned mine sites near Velva in Ward County, North Dakota. The sites studied were 1, 7, 17, 30 and 45 years old since abandonment; unmined sites were also studied to provide measures of comparison. Species diversity was the highest at unmined sites (114) and lowest at the I year old site (26); sites 7, 17,30 and 45 years old had 37, 52, 43 and 68 species, respectively. Stand ordination revealed that site ages were the most important in influencing species diversity and composition. Stand-environ-mental complex ordinations encompassing 53 variables showed topographic variables to be the most important followed by site ages. Rates of nutrient accumulations were as follows: organic carbon 13.1 g m-2 yr-1; nitrogen 2.5 g m-2 yr-1; phosphorus 0.01 g m-2 yr-1; potassium 0.49 g m-2 yr-1. Carbon-nitrogen ratios showed the widest range for 1 year old sites (5-40) but 70 percent of the 45 year old sites showed values below 15 which were com-parable to the unmined mixed grass prairie sites. Species distributional diagrams are provided to show their habitat preferences which may be helpful in formulating species prescriptions for revegetation.

Jan 1, 1982

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By C. J. Newman

Before 1995, the smelting process at the Kennecott Utah Copper Corp. (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. When considering expansion, it was decided that the existing process would not lend itself to a program geared toward processing the total output of copper precipitate and copper concentrate from KUCC mining and concentrating operations. During 1989 and 1990, several smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1 Mt/a (1.1 million stpy) of copper concentrate, with the ability to expand to 1.2 Mt/a (1.3 million stpy). The smelter facility that used the Noranda technology was shut down in May 1995. The flash smelting furnace operation began in June with the flash converting furnace start-up a few weeks later.

Jan 1, 1999

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989

By Willie M. NeSmith

Cast-in-place piling are a staple of the deep foundation industry, and are used (in various forms) worldwide. In assessing the application of cast-in-place piles, it is of value to reflect on the development of the various systems, in order to understand how the current processes and equipment came to be. This paper traces the evolution of the cast-in-place industry. Emphasis is on developments in the United States; however, since there has been a substantial fusion of US and European processes, notable European developments are also discussed.

Jan 1, 2006

By Vítor Covre Evangelista da Silva

Esta proposta objetivou desenvolver uma análise teórico/experimental da influência de 2% Ag (em peso) em uma liga de solda Sn-40%Bi solidificada unidirecionalmente em regime transitório de fluxo de calor. Correlações experimentais entre os parâmetros térmicos de solidificação como velocidade de deslocamento da isoterma liquidus - VL, taxa de resfriamento - ?L e parâmetros microestruturais como espaçamentos dendríticos secundários – l2 foram determinados. A caracterização microestrutural foi realizada por meio de microscopia ótica e eletrônica, difração de raios-x, além de fluorescência de raios-x para obtenção dos perfis de macrossegregação dos solutos (Bi, Ag). Para determinação do perfil de dureza foram realizados ensaios de dureza Vickers. As microestruturas brutas de fusão da liga Sn-40%Bi-2%Ag são compostas de dendritas ricas em Sn decoradas com partículas de Bi circundadas por uma mistura eutética (Sn+Bi) e partículas primárias de Ag3Sn. Os parâmetros térmicos decresceram com aumento da camada solidificada, permitindo uma ampla variação: ?L ? 0,1 a 10,0°C/s, VL ? 0,2 a 0,9mm/s e GL ? 0,4 a 11,0°C/mm. O teor de bismuto não variou significativamente, ao passo que a prata variou de forma efetiva, concentrando-se no início do lingote (até próximo de 35mm). O surgimento de braços dendríticos terciários em 15mm conteve a diminuição da microdureza Vickers, esperada para as posições mais afastadas da interface metal/molde.

Aug 16, 2017

By G J. Corbett, P Magner, M McKenzie

Structures formed during ductile deformation have been reactivated during the later brittle mineralisation process. Two generations of folding are classified as: early recumbent megascopic FI folds and FI shears which transpose the hinge regions, and later upright F2 folds. S1 is folded about F2 folds which contain axial planar S2 crenulation cleavage. Vergence relationships between S1 and bedding indicate that many of the mineralised structures occupy sites of FI folds which have acted as plumbing systems for later gold mineralisation (eg Blackwater mine). The Globe-Progress gold mineralisation is localised by a major jog formed by sinistral strike-slip movement on two FI fault segments and mineralisation also occurs in smaller jogs along strike (eg Sir Francis Drake, Happy Valley-Merrijigs, Cumberland).   The lodes of ribbon quartz which exploit the FI shears and local bedding planes, are inferred to have mostly formed after the peak of metamorphism, possibly related to the emplacement of Carboniferous granites. This was followed by a sequence of vein deposition and wallrock alteration which consists of quartz-As/Fe sulphides ? carbonate - stibnite ¦ trace base metal sulphides and Bi-sulphosalts ? illitic clay/sericite-chlorite. Gold at Globe-Progress is mainly encapsulated in arsenopyrite. At Blackwater, free high fineness gold occurs in partings in lode quartz with late sericite-chlorite. The above sequence of events is comparable to that encountered in many intrusion-related gold systems throughout the Southwest Pacific region. There is a spatial relationship between gold mineralisation and dykes variably described as diabase, dolerite or lamprophyre. Alkaline rocks occur in many Pacific rim and older goldfields and may possibly be related to a magmatic source for gold mineralisation.

Jan 1, 1997

By Kevin Beirne

Most people involved in the mining industry are familiar with student-industry co-op work-study programs. Many colleges and universities have used them for years. Northern College’s Haileybury School of Mines student co-op program adds a new dimension of productivity to the college and the mining industry. The college is located in Hailey-bury, Ontario, Canada. An example of the program’s success is the school’s relationship with Sabin Metal’s SMC (Canada) Ltd.’s McAlpine Mill in Cobalt, Ontario. Students gain practical knowledge and experience while industry gains an eager-to-learn worker. And many of the college’s advanced research services are made available to industry to supplement their own capabilities. The McAlpine Mill was established to provide custom milling of slags and ores. It also recovers metal values from other products of the primary and secondary precious metal industries.

Jan 1, 1999