Search Documents

The principles of geometry and trigonometry are so continuously used by mining engineers for the purpose of accurately and intelligibly recording their measurements, that the writer is prompted to lay the following cursory remarks upon mine surveying before the members of this Institution in the hope of eliciting a free interchange of opinion upon details of this interesting branch of the profession. He proposes to deal with surveying only so far as it concerns the mining engineer, not to intrude upon the domain of the professional surveyor, and, in this instance, to discuss more especially that which may be termed the mechanical, rather than the mathematical side of surveying.In the latter part of the eighteenth century and the beginning of the present one, the usual underground surveying equipment in the English metalliferous mines, consisted of a magnetic needle in a fiat square wooden box of about 9-inch sides, a two-foot rule, a long cord, aud a stool, upon which to place the needle and box. The operator took his bearing by sending his assistant with the end of the cord as far in a straight line as the length of the cord would admit.On its being drawn that he held its end in one hand and placed the side of the compass-box against it with the other, and noted the bearing thus found either by a book entry, or by ticking it off with a piece of chalk on the board the compass lay in. He then measured the cord with a two-foot rule. It is needles to say that with these appliances the accuracy of the results were open to question, and mining surveying was not unduly popular.In the present day, engineers have the advantage of using instruments brought to such a state of perfection, and of employing such an exact system of underground surveying, that inaccurate work must usually be attributed either to lack of care, or lack of ability in the operator.

By Joseph Ribak

Grunerite asbestos (amosite) has been shown in epidemiological and experimental animal studies to cause lung cancer, mesothelioma and pulmonary fibrosis commonly referred to as asbestosis. An overview of the human and experimental animal studies describing the health hazards of grunerite asbestos (amosite) is presented. Of the many human studies describing the health hazards of asbestos, only three factories using mainly, if not exclusively, grunerite asbestos (amosite) have been studied. The first is a series of reports on a cohort of 820 workers from a plant located in Paterson, NJ. Among this cohort, 18.7% died of lung cancer and 17 mesotheliomas occurred. The Paterson factory closed in 1954 and moved to Tyler, Texas where it operated until 1972. Among the 1130 former workers in the Tyler plant 6 mesotheliomas were reported with 15.8% lung cancer mortality. The third grunerite asbestos (amosite) exposed cohort was an insulation board manufacturing facility in Uxbridge, United Kingdom. Here 17.1% of the workers died of lung cancer and 5 mesotheliomas occurred. The lung content from 48 Uxbridge workers was analyzed by analytical transmission electron microscopy for mineral fibers. The relationship between grunerite asbestos (amosite) concentrations in the lung correlated with grades of fibrosis and asbestos bodies and was lower than the concentration found in the cases with malignant tumors. The lung cancer cases contained more grunerite asbestos (amosite) than mesothelioma cases, and in the cases of non-alignant disease the concentrations were still lower. In both types of malignancies the concentration of grunerite asbestos (amosite) was very high-over a billion fibers per gram of dried lung tissue. Occupational exposure to airborne concentrations of between 14 and 100 fibers of grunerite asbestos (amosite) per milliliter after 20 year latency causes marked increases in lung cancer, mesothelioma and pulmonary fibrosis (asbestosis). © 2007 Elsevier Inc. All rights reserved. Keywords: Grunerite asbestos; Amosite; Mesothelioma; Asbestosis

Jan 1, 2007

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

The project to reopen the Tasmania Mine has centred around efforts to reopen the Hart Shaft to access the high grade reef remaining below the old workings, which extend down to 457 in. Efforts in 1982 and 1987 were frustrated by unstable clay ground around the shaft, which resulted in significant subsidence of the shaft collar and lining. A successful program has since been implemented to solve the problems, stabilize the collar and recover the upper shaft which had collapsed down to 90 m.

Jan 1, 1989

By Healy T. W, Dixon D. R

The present study 'of pure ZnS and NiS and ZnS (marmatite) by detailed electrokinetic methods has shown that by careful control of experimental parameters much new' information on sulphide-water interfaces can be obtained. Time-dependent processes of alteration of sulphide surfaces are foHowed by electrokinetic methods and indicate that the isoelectric point of the surface depends on elemental sulphur coverage, oxidation product coverage, and the conditions which promote or minimize such reaotions in the presence and absence of activator.

Jan 1, 1977

In considering the preparation of any paper concerning bearing metals, one feels a certain amount of diffidence in venturing into a field which has been capably explored at great length and in great detail during recent years. Many excellent articles have appeared in technical literature, dealing with the general theory of bearings and of bearing metals, the properties of white metals of the tin-base and lead-base types, and of the recently developed lead-bronzes.The justification for this further excursion into the field lies in the fact that it treats a branch of the bearing metal family which has so far received very little attention, and that of a somewhat sketchy nature, in published papers.The author's object is to give some outline of the history, development, present status and possibilities of the cadmium-base bearing metal alloys, particularly those in which copper is the main alloying element.GENERAL CONSIDERATIONS.It is desirable that attention should first of all be given to the general theory, constitution, and necessary attributes of bearing metals, in order that some of the problems met with during the development work may be better appreciated.Despite some evidence to the contrary, it is fairly generally maintained that an alloy for bearing metal use should be of a heterogeneous nature. It should consist of particles of a hard constituent uniformly distributed through a softer matrix.The basic idea is that the hard constituent should actually bear the load and resist wear, while the matrix imparts the necessary ductility and allows the bearing to align itself on the shaft in service.

Jan 1, 1934

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

The rocks of Waihi and the surrounding district are almost entirely rhyolitic and ande5itic in character. Sedimentary rocks, with the exception of some surface deposits of clay loosely compacted conglomerate, etc., and one or two thin and broken beds of a very poor lignite, occasionally changed by igneous agencies into a bituminous coal, are almost absent. In the shafts sunk by the Waihi and Grand Junction companies outside the outcropping andesitic area of the Martha Hill, more than one old surface or lake bottom has been passed through. At these points layers of sand, consolidated volcanic mud and tuff, accompanied by numerous broken fragments of imperfectly silicified wood have been enccuntered, but these occurrences may, for the purpose of this paper, be neglected.The youngest rock of the district are rhyolites, probably of Pliocene age. At least three distinct classes of rhyolitic lava, each possessing features of unusual interest, may be made out. None of these, however, is gold-bearing. The youngest flow, a light-coloured, fine-grained rock, is remarkable owing to its enclosing at times fragments of carbonised wood, varying in size from mere specks up to quite large pieces of almost pure charcoal. Rhyolitic tuff is also met with. The rhyolites cover a large extent of nearly flat country east, south, and west of Waibi, here and there rising into barren, stony hills.Below the rhyolites, geologically speaking, but for the most part. forming hills which bound the rhyolitic plain, or rise out of it as isolated patches, come ahdesites of older...

Jan 1, 1902

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By Roy C. Fedotoff, Jon Hurt, Gregg Sherry, Gilbert Tang

The 1,380 m (4,200 ft) long New Crystal Springs Bypass (Polhemus)Tunnel (NCSBT) will replace the existing Crystal Springs Bypass Pipeline. This tunnel project is part of the SFPUC’s $4.3 billion capital improvement program to repair and seismically upgrade their aging pipelines, tunnels, reservoirs and dams that provide drinking water to more than 2.4 million customers in the San Francisco Bay Area. This paper describes the development of the tunnel alignment and design, and the complex ground conditions of the Franciscan Mélange. Of particular interest is the challenge of tunneling with a possible downhill grade of 3%, a rigorous environmental process and incorporating the lessons learned from 1960s construction of the adjoining Crystal Springs Bypass Tunnel.

Jan 1, 2007

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, 'compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, 'compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

By Richard Wilson

In the early 1970s, it became a concern that exposure to the mineral fibers associated taconite ore processed in Silver Bay, Minnesota would cause asbestos-related disease including gastrointestinal cancer. At that time data gaps existed which have now been significantly reduced by further research. To further our understanding of the types of airborne fibers in Silver Bay we undertook a geological survey of their source the Peter Mitchell Pit, and found that there are no primary asbestos minerals at a detectable level. However we identified two non-asbestos types of fibrous minerals in very limited geological locales. Air sampling useful for risk assessment was done to determine the type, concentrations and size distribution of the population of airborne fibers around Silver Bay. Approximately 80% of the airborne fibers have elemental compositions consistent with cummingtonite-grunerite and the remaining 20% have elemental compositions in the tremolite-actinolite series. The mean airborne concentration of both fiber types is less than 0.00014 fibers per milliliter that is within the background level reported by the World Health Organization. We calculate the risk of asbestos-related mesothelioma and lung cancer using a variety of different pessimistic assumptions. (i) that all the non-asbestos fibers are as potent as asbestos fibers used in the EPA-IRIS listing for asbestos; with a calculated risk of asbestos-related cancer for environmental exposure at Silver Bay of 1 excess cancer in 28,500 lifetimes (or 35 excess cancers per 1,000,000 lifetimes) and secondly that taconite associated fibers are as potent as chrysotile the least potent form of asbestos. The calculated risk is less than 0.77 excess cancer case in 1,000,000 lifetimes. Finally, we briefly review the epidemiology studies of grunerite asbestos (amosite) focusing on the exposure conditions associated with increased risk of human mesothelioma. © 2008 Elsevier Inc. All rights reserved. Keywords: Risk; Fibers; Particles; Taconite; Asbestos; Exposures

Jan 1, 2007

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By Mike Watts

Since the first longwall panel development started in the new mining, (Southern) area, a number of roof falls have occurred in L1 and L2 gate-entries. The longwall was delayed for a total of two months due to roof falls in the gate-entries. To prevent roof falls in future gate-entries, an extensive ground control analysis has been conducted which incorporated regional horizontal stress and panel orientation, tectonic stress, roof strata, surface stream valleys, etc. Results of the analysis indicate that a combination of these factors caused the roof falls. Therefore, a Roof Instability Rating (RIR) system was constructed to predict the roof condition and identify areas where supplemental support should be implemented. The L3 gate-entries, supported by the prediction using the RIR system, have not experienced any roof problems.

Jan 1, 2000

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003