Search Documents

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By Walter R. Hibbard

Whether we have occasion to think of it or not, an adequate and economic supply of energy fuels is vital to each of us. It is interesting to look ahead at the way in which fuels from supplementary sources will begin to enter into the energy mix to help meet the long-term national energy needs. From 1947 to 1965, the average annual rate of growth of energy consumption was 2.7%, with total energy demand in 1965 being equivalent to 54 quadrillion Btu's. During this short period of 18 years, the cumulative output of coal in the U.S. was 9.6 billion tons; natural gas, 193.5 trillion cu ft; and crude oil, 45.9 billion bbl. During the next decade and a half the nation's energy requirements are expected to grow at an average rate of 3.3% yearly, with consumption of energy expected to reach an annual rate of about 88 quadrillion Btu's by 1980, or 63% over the 1965 level.

Jan 12, 1967

By James A. Todd

Use of AN-FO in underground operations has greatly reduced the cost of primary explosives. AN-FO is also less sensitive than conventional dynamites, and when properly used, is safer. Maximum safety in the use of AN-FO, however, requires an understanding of potential hazards from toxic fumes as well as static electricity developed in pneumatic loading. Safe limits and guides have been established to permit most operations to pneumatically load holes that are bottom primed with electric blasting caps, but the toxic fume hazard is less widely understood. During 1959-1960 Du Pont cooperated with the U.S. Bureau of Mines to study the toxic fumes produced by prilled ammonium nitrate-NO. 2 fuel oil mixtures. The conclusions from this work were that oxygen balanced AN-FO, when thoroughly mixed, well primed and well confined in dry holes, produces no greater amounts of toxic fumes than conventional dynamites rated Class I by the Institute of Makers of Explosives. The study also showed, however, that any deviation from these guides tends to increase significantly the quantity of toxic fumes produced. This work was reported by the Bureau of International Symposium on Mining Research at Rolla, Mo., in February 1961.'

Jan 4, 1963

By Charles M. Brinckerhoff

Everyone -- especially the engineer -- is aware of the great technological and social changes taking place in our world today, We realize that changes have been taking place since man's beginnings on earth, but the element we now face is the speed of change, rather than change itself. Developments in medicine, in transportation, in space exploration, in global communications, and in many other fields, are constantly being made known. These developments are affecting the lives of each of us, although some may appear remote and unrelated to us as individuals. New developments, almost on a daily basis, affect our work as well as our social, religious and educational lives. The effects are immediate and permanent.

Jan 1, 1967

By V. Dinesen

"Grinding is simply the function of reducing particles in size or creating new surface areas. This may be accomplished by many means but we will only concern ourselves with the continuous grinding process as performed in a revolving drum or mill, containing a grinding media. Such a mill consists essentially of a feed head, a cylindrical shell section and a discharge head. To prevent internal wear of these parts it is customary to attach replaceable linings over the wear areas. The specification and design of these mill liners is more important than generally conceded. As they reduce the effective internal volume of the mill, they will consequently affect the whole mill ·design and operation.A number of mill designs of various sizes are available for combined crushing and grinding of materials within a wide size range. For simplif1cahon purposes we will refer 1n particular to conditions relating to standard mill shapes having a length which is greater than the diameter. Such mills usually rotate at speeds between 60% to 85% of the critical speed and may, depending on the grinding media used, be classified as rod mills, ball mills and pebble mills.LINER MATERIALSA great variety of materials have been and are being used for mill linings. These include wood, ceramics and cements, rubber and plastic compounds, rolled and forged steels, cast steels and cast irons, both plain, alloyed and specially treated.The choice of a liner material depends on many factors. In both dry and \\.:et grinding, it may be necessary to consider product purity, colour, chemical reaction etc. but for our purpose we \viii refer to wet grinding operations as generally used within the mining industry."

Jan 1, 1972

By Sharon K. Young

What might an ideal leach-to-cathode/product system look like in the next century? The paper looks at the synergies of the 60's and 70's that led to the highly effective copper leach SX-EW system of the 90's. Standing in the year 2020 focuses on what breakthrough technologies might make possible a next generation leach/extraction/metal recovery system. Many of the pieces of such a technology have been developed, even piloted: in situ leaching, enhanced bioleaching, heap leaching of fine particles, resin in pulp, ion exchange, alternate anode reaction electrowinning, novel anode coatings. With nearly non-existent research on the part of individual large companies, the greatest challenge may not be inventing the technologies but rather inventing an industry "will to create."

Jan 1, 1999

By D. L. Watson

In spite of the deflationary state of the minerals business today, there will be opportunities for those who can fulfill future needs. Since there are abundant supplies of ores and fuels to keep prices down, at least in peacetime scenarios, future needs may be as much political and social as technical and economic. Engineers and economists will develop new and innovative ways to find, mine, process and pay for mineral deposits. Pressure from governments and non-governmental organizations and the public will combine with market forces to provide opportunities for highly competitive, risk-taking enterprises who can leverage the qualities of their orebodies and employees by being good neighbors and partners.

Jan 1, 2000

By Clifford J. Lewis, James L. Drobnick

Vexed with competition from relatively high grade foreign orebodies, perplexed by marginal, low grade domestic orebodies, and ironically faced with the fact that practically every metal needed in our economy is available domestically in ample quantity in the ground, our mining industry awaits the advancements in beneficiation technology that will bridge the gap between the ground and the market place for our presently unexploited mineral reserves. Among the vast number of research and development projects underway in the metals mining industry, there are a few chemical techniques in metals winning that, with further development or wider application, could have a profound effect on the industry. These techniques include the Imperial Smelting and Refining Process for complex lead-zinc ores, chlorination and fused salt procedures, the liquid ion exchange process, and the field of non-aqueous leaching. IMPERIAL SMELTING PROCESS The Imperial Smelting and Refining Process is of interest because it offers a possible economic route for the processing of complex zinc-lead-copper ores. The process represents the outcome of the combined efforts of metallurgists and engineers of Imperial Smelting Corporation. Ltd., the United Kingdom Subsidiary of the Consolidated Zinc Corporation, Ltd., and is the subject of patents throughout the world. This process is essentially the employment of the blast furnace for the production of zinc. Zinc has always resisted blast furnace technology, primarily because of the difficulty of condensing zinc vapor from dilute gases. The Imperial Smelting Process employs a blast furnace working at ordinary pressures and in a system which is able to con- dense a blast furnace gas of a very low zinc content.

Jan 11, 1963

By Y. Takahashi, I. Iwasaki, S. Tanabe

Supported by the vigorous capital investment of the heavy and chemical industries and by the ever-increasing demand for durable consumer goods in the past decade, Japan has now emerged as the world's third largest steel producer, surpassed only by the United States and the Soviet Union. In 1968, the crude steel production is expected to exceed 50 million tons; the per capita steel consumption at that time will reach 886 lb, approaching the level of Western Europe. Characteristics of the Japanese steel industry is the high dependence of raw materials on overseas sources. Before World War II the industry relied on North China and Manchuria for coking coal, and on middle China, Hainan Island, the Philippines and the Malayan Peninsula for iron ores. After the war, the major sources of iron ores were shifted to the Philippines and the Malayan Peninsula, supplemented by shipments from the United States, Canada, India and Goa. The United States, in addition, became the primary source of coking coal.

Jan 1, 1967

By A. B. Rossetti

"THE MISSION TO Offshore Scotland was in my opinion a very worthwhile venture, as it indicated the scope of the offshore oil and gas business and how we might exploit it to the fullest here in Nova Scotia - if our offshore fields eventually become producing fields. The writer was able to attend a considerable number of lectures and as a result gained some valuable know-how on the engineering design, financing and operation of the North Sea oil industry. There are many new fields of technology that had to be developed to overcome the North Sea's hostile environment and a great deal of the same technology will have to be developed to win oil and gas from our continental shelf. The visit left me with several impressions, which in the main are:(1) The high order of investment required to develop offshore oil. The investment ranges from 10 to 20 times that required for a similar output on land. Each barrel of oil costs on the average of about $2,- 500 per barrel per day.(2) Because of the high investments required, before the first oil is produced the field must be brought into production at the earliest possible date and initial lead time from decision to production is less than four years. In the British Petroleum field, working at a depth of 450 feet will require an investment of $900,000,000 to develop a production of 400,000 bbl per day. (3) The size and complexity of equipment required is beyond anything ever imagined. Problems which must be overcome are such factors as water depth, wind velocities, wave height, wave period, long periods of darkness, low temperatures, distance from land, and fog."

Jan 1, 1973

By A. F. Peterson

MUCH has been said and written about the engineer shortage. The mining branch in engineering has lagged during the past several decades. I can think of two institutions, formerly prominent in that field, that have discontinued this department and another that has branched from a purely mining school into various forms of engineering. Conversely, I do not recall any institutions that have added mining to their curricula. I believe that this action is in direct response to the demands of incoming students. But I also believe that while there is a specific demand for civil, mechanical, and electrical engineers in the highly complicated mining operations of today, our need for mining engineers capable of assuming top responsibility for mining operations is unchanged.

Jan 3, 1957

A comprehensive, systematically structured mineral evaluation system is a prime requirement for objectively assessing mineral supply impacts on the economy. The Minerals Availability System developed by the US Bureau of Mines is a step in the right direction-a well-organized unraveling of the mineral supply network, structured in format to allow quick retrieval for rapid listing, supply analysis, and other uses.

Jan 9, 1977

By S. G. Vick, K. E. Robinson, W. D. Webb

INTRODUCTION This paper discusses two uranium tailings waste disposal studies that reflect the United States Nuclear Regulatory Commission (NRC) regulatory actions and their changing requirements during the mid to late 1970's. Present guidelines require that all new uranium tailings impoundments be designed and constructed to eliminate, to the extent that it is reasonably achievable, exposures and risks to the public from the tailings. This includes positive measures for control of seepage losses from the impoundment and for control of radiological releases caused by wind and water erosion. Long-term stability of the reclaimed impoundment is also a very important requirement. That is, it is intended that the tailings impoundment, once it is reclaimed, will require little or no care or maintenance as long as the uranium tailings remain a hazard. Principally because of the long-term stability objective, the NRC has now identified subsurface burial of the tailings as the "prime option" for tailings disposal. The environmental implications of these proposed regulatory actions are obviously desirable. The economic implications the actions may have on a particular project are not always so obvious because they are so dependent on environmental suitability of site conditions. Selection of a site with favorable topographic, geologic and hydrologic conditions will usually result in the most economically and environmentally attractive alternative for tailings disposal. The first project discussed in this paper was initiated before the NRC guidelines had been developed to favour subsurface burial. At the beginning, seepage and radon emission control requirements were moderate. Constraints were imposed on the design by site topography, geology, and project capitalization considerations, factors which were dealt with according to straightforward engineering and design principles. More serious constraints were imposed by changing regulatory requirements. Unlike the more usual engineeringrelated constraints, regulatory requirements were upgraded during the design process, causing the design itself to undergo numerous modifications. The second project was initiated after the NRC proposed regulations had become better defined and below grade burial appeared to be the preferred

Jan 1, 1980

By W. C. Spence, Burt C. Mariacher

Methods employed to beneficiate ores utilize relatively few fundamental principles to effect size reduction and concentration. In crushing and grinding only impact and compressive forces with a minor amount of shear are employed. In concentration, gravity, magnetic, electrostatic and flotation constitute the major methods of concentration with minor use of sizing, hand picking and adhesion. This industry, as all others, can expect in the near future to see the development of new techniques for improved efficiency, cost reduction, and exploitation of raw materials hitherto considered unmanageable. NATURAL AND INDUCED RADIOACTIVITY At the Canadian Department of Mines in Ottawa in 1946, C. M. Lapointe developed a picker belt system whereby radioactive ores could be concentrated by electromechanical means. This invention ultimately led to development of what is now refer- red to as the Lapointe Picker and which has been used commercially at Port Radium and Port Hope for the upgrading of jig concentrates. Basically, the system consisted of conveying sized uranium ore on a belt under a radioactivity detection device which in turn electronically operated a kicker or plunger that separated the ore from the gangue constituents. Thus, a new principle for mineral concentration, radioactivity, was introduced commercially.

Jan 7, 1962

A Loss of Strength of Gold Sulfide Concentrate Before Grinding and Cyanidation Using Magnetic Impulse Treatment Gold recovery from sulfide concentrates is going with cyanidation usually. The fine grinding to 95 per cent -0.020 mm is required for refractory concentrates, in which gold encapsulated by sulfides. According energy consumption is 10 and more kW h/ton. At this paper we suggested to use magnetic-impulse treatment with small energy consumption 0.1-0.2 kW h/ton for loss of sulfide strength before grinding and cyanidation. The object of studies was the gold-pyrite flotation concentrate which was produced from ores at the Kumtor Mine, Kyrgyzstan. The concentrate composition, physic-mechanical properties and loss of strength mechanism were studied there. The tested concentrate assayed, per cent: 62.5 pyrite, 10 feldspar, 10 mica, 5 quarts, 5 carbonates, 4 haematite and another. Haematite has intimate intergrowth with pyrite ? partially with quarts. The magnetic susceptibility of haematite and less pyrite causes in these grains and mineral complex the effect of magneticstriction. As a result numbers of deformations are increased and minerals and gold are also exposed. Lateral and longitudinal strains in the minerals by magneticstriction were calculated in this work. By quantitative analysis of pyrite mono fractions were showed next micro impurities: alumina, arsenic, nickel and others elements. These micro impurities are generated a charged dislocation, cracks and micro cracks. The inter-granular links at a boundary of haematite-pyrite, pyrite-quarts, haematite-quarts have disintegrated. The dislocation is depended from mineral modulus elasticity. It was determined an indicator of mineral electro-mechanic sensitivity which characterises a conversion of electro-magnetic energy to mechanic energy. Pyrite has most dielectric constant and electro-mechanic sensitivity as haematite and quarts. The dislocations in pyrite are account for clacks and a loss of mineral strength. Size analysis of the flotation concentrate after magnetic-impulse treatment is shown the increasing the content of thin fractions by comparison no treated concentrate. Magnetic-impulse treatment has increased the effect of the next fine grinding too. The electronic microscopy has confirmed a loss of strength of gold sulfide concentrate. The gold recovery by cyanidation increased too after preliminary magnetic-impulse treatment of concentrate by laboratory tests. The magnetic-impulse concentrate studies at the Kumtor plant have showed that a recovery gold increase in the processing of cyanidation. The consumption of energy also reduced.

Sep 13, 2010

By George T. Wickes

(Washington Meeting, May, 1905.) SEVERAL years ago, Mr. Robert A. Cook described and illustrated in our Transactions 1 a mechanical coke-drawer, patented in 1891 by Mr. Thomas Smith of the Thorncliff Iron Works, Sheffield, England, and first introduced in the United States in, 1896, at the coking-plant of the Latrobe Coal Co., Latrobe, Pa. This machine has not received any very extended application in this country, although it was successfully used in two places for a number of years. The present. paper describes a new and simpler machine, containing few wearing-parts capable of withstanding continued rough usage. Anything which tends to prolong the general use of bee-hive ovens will be welcome to those who are interested in cheapen¬ing the cost of producing coke in such ovens, especially if it provides satisfactory mechanical means, replacing the hard labor involved in drawing coke by hand with the old-fashioned ?duck bill.? The difficulty of finding efficient coke-drawers, especially during the summer season, and in the South, is notorious. Yet, notwithstanding the great improvements that have been made in retort coke-ovens, new bee-hive ovens are continually constructed; and a machine which will successfully compete with hand-drawing, and, at the same time, add to the efficiency of the bee-hive oven, seems to deserve notice. The machine here described was put in operation at the Frick Coal and Coke Co.'s plant, known as Continental No. 1, at Uniontown, Pa., in October, 1904, and is reported to have met successfully all the tests to which it has been subjected. This trial has demonstrated that one of these machines, equipped with an electric motor, and operated by one mart with an assistant, besides two men to " water down " the

Jul 1, 1905

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000