Search Documents

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Benjamin Mirabile

"Current and emerging practices to ventilate longwall gobs are prompting increased design and analysis of standing support requirements related to longwall mining. Specifically, additional design methodologies are being employed to evaluate standing supports in the #2 entry of a 3-entry longwall system.Numerical modeling will be used to evaluate the performance of standing support in the #2 entry between gobs of longwalls in the Herrin No. 6 seam. The performance of standing support in the #2 entry will be evaluated based on the following: (1) The effectiveness of standing support in maintaining an open airway in the #2 entry; (2) The interaction of standing support in the #2 entry with standing support in the longwall tailgate; and (3) Loading conditions of longwall pillars. Initial numerical modeling activities are focused on evaluating the roof to floor convergence in the #2 Entry and using the ground reaction curve concept for support design.Numerical modeling indicates that, like standing support in tailgates, supports in the #2 entry require some type of yield mechanism to withstand initial uncontrolled convergence. Numerical modeling also suggests that support density can be lower than that used in a tailgate support application. The numerical models used for initial investigation of support performance in the #2 entry are limited in their ability to evaluate support performance. The magnitude of uncontrollable convergence can be estimated with LaModel software. Near-seam conditions have not been investigated in this research since the LaModel software does not have the ability to evaluate inelastic rock behavior.IntroductionDuring the past three decades, many researchers have investigated standing support performance in longwall tailgate entries. Very little attention was paid to the middle entry of a threeentry longwall gateroad. As longwalls retreated, no personnel would travel the #2 entry, and the entry was considered part of the longwall gob. In response to recent mine disasters, regulatory agencies and operators have devoted more attention to these entries. Prior to the Upper Big Branch mine disaster, little or no secondary support was applied in these entries. Unlike secondary support in longwall tailgates, there is little empirical knowledge or quantified research specifically applied to secondary support in the #2 entry. This paper outlines initial steps used to develop a design methodology for secondary support in the #2 entry."

Jan 1, 2015

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015

By T. J. McMahon

This Bureau of Mines study describes the development of a large-scale, three-dimensional, finite-element model of a deep-vein Coeur d?Alene District mine. The three-dimensional model was prepared from combined digitized mine maps and generated levels that may also be analyzed as independent two-dimensional models. A comparison of the stress changes and displacements was made following a simulated vein excavation in both the three-dimensional and two-dimensional models. A one-cut excavation was simulated with the two-dimensional model and a multiple-cut excavation was simulated with the three-dimensional model. The compared results from the two analyses are discussed in terms of the inherent differences between the models.

Jan 1, 1989

By Alexandra Garcia

A measurement-based ground control management system, commonly employed in coal mines, has been successfully implemented in a UK potash mine operating at a depth of over 800 m. This system includes the routine deployment of telltales in roadways throughout the mine to mitigate against the risk of large-scale roof falls and the deployment of detailed ?design monitoring? instrumentation for ongoing design verification. The routine monitoring systems used in coal mines have not been, to date, commonly applied in potash mines, despite the similar, variable weak geology and associated ground control hazards. Monitoring information from the site indicates that telltales can be deployed to monitor roof conditions, with action levels based on differential rates of strain, as opposed to absolute movement.

Jan 1, 2014

By Kazem Oraee-Mirzamani, Nikzad Oraee-Mirzamani, Arash Goodarzi

"Unexpected movement of ground can potentially endanger lives, damage equipment or destroy property. Occupational accidents frequently occur with fatal consequences in developing countries with significant economic dependence on industries such as mining. Therefore, there is increasing need for miners' protection against such hazards. Slope stability and roof support accidents are two of the major causes of fatalities at surface and underground mining operations. According to national codes, employers are obligated to protect workers against accidents; however, these rules fall short of the standards in developed countries. National safety regulations should clearly specify support systems. The International Labor Organization (ILO) prepared two codes of practice, aiming to guide those responsible for improving standards of safety and to provide guidelines for drafting of safety regulations for the coal mine industry and quarry open cast mines. The practical recommendations of these codes in the ground control area have been analysed and the advantages and disadvantages of ILO codes concerning ground control are summarized.INTRODUCTIONTwo million people die every year from work-related accidents and diseases. An estimated 160 million people suffer from work-related diseases, and there are an estimated 270 million fatal and non-fatal work-related accidents per year. In economic terms, the ILO has estimated that 4% of the world's annual GDP is lost as a consequence of occupational diseases and accidents (ILO, 2009).Mining has always been dangerous due to many potential risks such as those associated with using machinery in enclosed spaces, rock falls, blasting operations and explosion of flammable gases, which endanger miners' safety and health. However, it is suggested that implementing new laws along with strict adherence would reduce such risks in the workplace.The severity and frequency of accidents are trending downward in developed countries, where the focus is on large private companies who invest heavily in mechanization and developing economies of scale. But in many parts of the world, particularly in developing countries, minerals are extracted by people working with simple tools and equipment; they work on a smaller scale, are more flexible, and can exploit irregular ore bodies and steep, dipping seams."

Jan 1, 2010

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By Denise Mueller, Axel Preusse

"In 2010, the fracking discussion in Germany caused a number of changes in German law, which came into force in 2016. Especially the production of gas had to be regulated. With the legislation amendment, the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbereichs-Bergverordnung) has been revised, too. The changes expand the compensation of mining damages, especially to the extraction with drilling from the surface and underground storage. Although the “Subsidence-Area Mining Regulation” has been revised, the area of main influence (subsidence of 10 cm) remains to determine a relevant boundary for mining damages. The determination and prediction of this boundary above caverns are presented in this paper. In addition, further elements of ground movements and their relevance to mine damages are analyzed. The usage of the area of main influence to fix a relevant boundary for mining damages does not correspond to the relevant elements of ground movements. A limit for differences in subsidence (tilt) or horizontal changes in length should be preferred to describe the relevance of mining damages on buildings. Furthermore, this paper outlines the the meaning of using the area of main influence to fix a relevant boundary for mining damages. INTRODUCTION The “Federal Mining Act” (in German: Bundesberggesetz, short: BBergG) forms the central legal standard to cover subsidence in Germany. The mining authority refers to the following regulations (Preuße et al., 2015): the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbergverordnung, short: EinwirkungsBergV; since 1982) the “Mine-Surveyor Mining Regulation” (in German: Markscheider-Bergverordnung; short: MarkschBergV) the “Deep-Drilling Regulation”"

Jan 1, 2017

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018