Search Documents

By Albert Musschoot

The expanding applications of vibrating feeders for controlling the flow of bulk materials, and their adaptation for processing requirements, have developed considerable interest in stockpiling and reclaim systems. The general design of these units consists of a material transporting trough, or platform, driven by a vibratory force system. Design flexibility and variety is limited only by engineering ingenuity. The basic motion of the vibratory trough, or work member, is a controlled directional linear vibration that produces a material tossing or hopping action. Material travel speeds vary from 0 to about 30 m/min, depending on the combination of frequency, amplitude, and slope vibration angle.

Jan 6, 1981

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Aijuan Zhang, Liang Zhao, Yutao Wang, Yu Bao

In the green backfilling mining of underground coal mines, gangue in a coal seam is used to replace and fill goafs. However, the gas drainage time changes in the amount of gangue output and order in the extraction sequence of stope blocks, thereby changing the production output. A multi-objective integer programming model was proposed to solve this based on an improved non-dominated sorting genetic algorithm. The results show a feasible gangue filling rate can be found and the extraction sequence for a long-term planning time is optimized. It increases the planned annual output by 26% and reduces equipment idle time.

May 23, 2022

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By Francesco Chiappalone, Filippo Azzarà, Raffaele Aliberti, Daniele Nebbia, Lance Waddell

As part of the 3RPORT and NEBT Projects, 5-mile Combined Sewer Overflow Tunnels were excavated with a 19 ft diameter Slurry and 26 ft diameter EPB Tunnel Boring Machines. Due to the difficult geological and hydrogeological conditions, both tunnels were excavated maintaining a ground support pressure between 2 and 5.5 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of both projects while the second part focuses on the challenges and technical details of the pressurized breakthroughs that took place in deep shafts excavated in urban environment as part of the projects.

Dec 1, 2022

By D. P. Tao, J. G. Groppo, R. Killmeyer, W. W. Wen, B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 ~ 25 m) clean coal slurry produced by the `Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 165o cake formation angle, provided a filter cake with 23.6percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of `orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Anuradha Khetwal, Sandeep Khetwal, Andrea Panciera

The observation method is a design optimization approach for the drill and blast method in tunneling. This method includes first identifying the hazard scenarios through site investigation, formulating suitable solutions, obtaining feedback during construction, and finally using that data to optimize the design methods. This paper illustrates the application of the observational method for T-48, a railway tunnel project in the Himalayas. It is a 10.2 km long tunnel with a parallel escape tunnel and 26 cross passages. The use of observational methods in this project optimized the overall tunnel design and considerably saved the overall project cost.

Jun 23, 2024

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By Kenneth F. Wyman

The following report details the successful construction of Contract 2A of the Three Rivers Water Quality Management Program, Intrenchment Creek Combined Sewer Overflow Conveyance System, in DeKalb County for the City of Atlanta, Georgia. The contract required construction of approximately 2878 m (9443 ft) of tunnel bored to an initial diameter of 7.95 m (26 ft 1 in), with provisions to concrete line those portions designated by the engineer to a finished internal diameter of 6.91 m (22 ft 8 in). Flanking the tunnel are two shafts. The upstream shaft was excavated to a nominal diameter of 4.87 m (16 ft) to accommodate a finished internal diameter of 3.66 m (12 ft). This shaft required a transition boot fully concrete lined to final dimensions of 6.91 m (22 ft 8 in) wide, 13.72 m (45 ft) long, and varying in height from 6.91 m (22 ft 8 in) to 12.80 m (42 ft). Associated work necessary to complete the contractual obligations included installation of 22.86 m (75 ft) of cut-and-cover box culvert, 484 m (1589 ft) of open-cut sewer installation in sizes ranging from 0.30 m (12 in) to 1.68 m (5 ft 6 in), one river crossing, 137.46 m (451 ft) of monolithic concrete trapezoidal channel, and installation of 19125 cu m (25000 cu yd) of select fill material compacted and graded to finished contours. The downstream shaft was excavated to a minimum diameter of 12.04 m (39 ft 6 in) and concrete lined to a finished internal diameter of 10.67 m (35 ft). Requirements here included installation of a complete pumping station with all mechanical, electrical, and structural elements necessary for dewatering the tunnel through the controlled use of four 250 hp submersible pumps discharging into the facilities of the Intrenchment Creek Water Pollution Plant. The objective of this project was to collect combined storm runoff and sanitary flows currently coursing through Intrenchment Creek

Jan 1, 1985

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002