Search Documents

By M. Weatherspoon, S. Gebo, K. Prisbrey

Our objective was to develop a transfer function model of phosphate heap leaching for design, optimization and control. The procedure included analysis of time-lapse photography of a laboratory heap. Our experimental results confirm the predicted system transfer function kinetics. Our conclusion was that the transfer function and z transform that we have developed will allow us to control flow rate and pH online.

Jan 1, 2001

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By Harry R. Price, Behrooz Tahmasbi, Charles J. Roarty

The 2,408 meter (7,900-foot) long Middle Rouge Parkway Interceptor Extension varies in size from 1.52-meter (5-foot) to 2.36 meter (7-foot 9-inch) inside diameter. Most of the sewer was constructed in tunnel through fine sands and silts. Piping of these soils through the concrete liner eventually resulted in a loss of soil support, settlement and/or severe distress of the sewer, and the formation of several sinkholes. The repair and restoration was generally performed in the sewer and included cast-in-place concrete, shotcrete, cured in place pipe, soil stabilization, cement grouting, dewatering, and chemical grouting. As a part of the work, temporary pump stations and flow diversions were required to perform the work while minimizing discharges to the adjacent Rouge River.

Jan 1, 2007

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

By M. A. Trevits

Mine seals are used in underground coal mines throughout the United States to isolate abandoned mining areas from the active mine workings. The objective of adding inert gas to a sealed mine area is to quickly reduce the oxygen concentration in the sealed area to a level that will not support combustion. In the US, this process is typically conducted from the ground surface and because surface-to-mine access is constrained by so many variables, it is very difficult to provide a source of inert gas to the place where it is needed underground. To alleviate this problem On Site Gas Systems, under a NIOSH contract, built a nitrogen (N2) generation plant that operates in the underground environment. The purpose of this work was to create a reliable in-mine mobile plant that would extract N2 gas from the mine atmosphere and use the gas to create and maintain a safe sealed mine area. The plant is based on a novel design using pressure swing adsorption technology and is sized to fit on a standard shield car or mine dolly for easy transport in and around an underground coal mine. The plant is capable of producing about 900 scf/min of N2 gas at ambient mine conditions. After an exhaustive series of laboratory tests, the plant was field tested at the NIOSH Safety Research Coal Mine (SRCM) where a portion of the mine was sealed and rendered inert. During the test, the movement of the injected gas was monitored at several underground points to observe the progress and extent of the inerting process. This paper describes the plant design and the results of the field test at the SRCM. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013