Search Documents

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

[ ]

Jan 1, 2011

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By John P. Carter

The U.S. Bureau of Mines conducted research to determine suitable construction materials for use in brine and steam environments produced from high-salinity geothermal brines. The high-temperature, high-salinity geothermal brines in the Salton Sea Known Geothermal Resources Area (KGRA) are a valuable source of energy and mineral values. The brine and steam produced from them are corrosive and cause early failure of many common materials of construction. Mass-loss and electrochemical corrosion measurements were conducted on over 60 metal alloys in brine and steam environments produced from geothermal well Magmamax No.1, located at the Salton Sea KGRA, at temperatures from 1800 to 2150 C, and in synthetic Magmamax brine at 105° and 232° C. General corrosion, crevice and pitting corrosion, and stress corrosion were examined along with the effects of dissolved gases. The alloys with the most acceptable corrosion performance in high-temperature, high-salinity geothermal environments were the high-chromium ferritic stainless steels, the Inconels and Hastelloys, and the titanium alloys. Specific alloys that performed well in wellhead brine included Fe29Cr4Mo, E-Brite 26-1, stabilized Fe26Cr1Mo, 6X, Inconel 625, Hastelloy C-276, Hastelloy S, Hastelloy G, Ti5OA, TiO.2Pd, and TiCode 12.

Jan 1, 2010

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By Lon A. Williams

This report, authorized under Contract Number H0220065, Amendment Number Six, documents the results of an investigation of lighting system modifications and designs for working place illumination in high and low coal entries of underground coal mines. The portable and machine mounted system designs, both modified and prototype, represent a continuation of work performed under Contract Number H0111403, Amendment Number One. See the Final Technical Report dated May 26, 1972 for detailed information concerning this prior Contract. All modified and prototype systems met the performance requirements of Bureau of Mines Specification 2G, as proved by test. In addition, the systems met the requirement for illumination, as specified in the Contract and in the proposed standards which were generated in response to Public Law 91-173.

Jan 1, 1976

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

This report is the 24th in a series summarizing research on coal and related investigations3 by the Bureau of Mines. The coal programs of the Bureau of Mines include a wide range of theoretical and applied studies--such as fundamental studies of coal structure and properties, the development and evaluation of new mining techniques, and work toward more effective processing and utilization of coal. The scope of these programs is indicated, in topical outline, by the table of contents. These investigations are integrated into a broad but coordinated effort to develop information on coal that will benefit the coal mining industry and the coal consumer while promoting the wise conservation and utilization of our national coal resources. Any attempt to summarize in one volume the progress in all of the program areas indicated must necessarily be limited to a brief review of developments, without detailed reporting of the data. However, while the brief discussion in each section will present only the highlights of the Bureau's work during the year, details of many of the operations or investigations described here can be found in the publications cited throughout the text. Other work, reported here for the first time, will be covered in greater detail in later publications.

Jan 1, 1962

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

Bahrain's oil revenue increased from $337 million2 in 1916 to $378 million in 1977. Despite the increase in value, petroleum receipts made up only 584 of all Government income in 1877, compared with 74% in 1976 and 83% in 1975. Bahrain became an oil producer in 1932 with the discovery of the Awali oilfield, and since that time, the Awali oilfield has produced over 600 million barrels of crude oil. Awali production in 1977 was 21.2 million barrels. Bahrain shares the revenue from the Abu Safah oilfield, located in the Persian Gulf north of Bahrain, equally with Saudi Arabia. Revenue from the Abu Safah oilfield was approximately $179 million or 47% of oil revenues in 1977. Output from the Abu Safah oilfield was 48 million barrels, an increase of nearly 30% over 1976 output. The Bahrain Petroleum Company (BAPCO). the nation's only oil-producing company, was owned 40% by California Texas Oil Corp. (CALTEX and 60% by the Govern¬ment. The Government established Bahrain National Oil Co. (BANOCO) in 1976 to administer the Government's share of BAPCO, oversee exploration concessions, and manage domestic marketing of petroleum products. The Government announced its intention to acquire 100% control of crude oil and natural gas production. CALTEX was to retain complete control of the 250,000-barrel-per-day oil refinery near Sitrah.

Jan 1, 1981

By R. B. Fisher

This report gives the results of mineralogical research on the Nicaro (Cuba) nickel ores and plant products. These studies were made under a cooperative agreement with the General Services Administration (GSA) of the U. S. Government. The purpose of the investigation was to obtain fundamental data that would be useful to other GSA contractors concerned with the Nicaro ores in their research on reduction roasting, leaching, and other phases of the project; and to the metallurgical staff of the Nicaro plant in Cuba. The overall objective of the combined research was to provide data to accomplish metallurgical improvement in the operations of the U.S. Government-owned plant at Nicaro, Oriente Province, Cuba. Particular emphasis is placed on improving the recovery of nickel from the ores and on the possibility of recovering other valuable constituents, especially cobalt. This study presents the physical and chemical characteristics, mineral associations, differential thermal analyses in controlled atmospheres, and X-ray studies of the ores and plant products. The nickel ores, serpentine and laterite, were from the Ramona-Lama Mulo and Ramona ore deposits. Serpentine ore consisted of serpentine-group minerals, basic iron oxide, magnetic iron oxides, chromite, olivine, enstatite, anthophyllite, cryptocrystalline quartz, wad, and a trace of calcite. This ore contained 1.6 percent nickel, 0.05 percent cobalt, 0.86 percent chromium, and 17.4 percent iron. Laterite are was composed principally of goethite with some altered serpentine, quartz, chromite, wad, magnetite, maghemite, and hematite. It carried 1.3 percent nickel, 0.11 percent cobalt, 1.9 percent chromium, and 48.4 percent iron.

Jan 1, 1959

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006