Search Documents

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By L. Villa, O. Suarez, D. Arias, L. G. Corretge

The deposit comprises two vertical, lenticular bodies emplaced in the allochthonous block of a Variscan thrust. Epigenetic mineralisation occurs as replacement of carbonated volcaniclastic rocks of Cambro-Ordovician age. The dominant sulphide minerals are sphalerite and galena with minor chalcopyrite; the main non-metallic mineral is quartz and there is hydrothermal silicification, chloritisation and sericitisation. Sulphur isotope values for sphalerite and galena are heavy and reflect the fundamental relationship between delta-34S in ZnS and in PbS, suggesting isotopic equilibrium. Four sphalerite-galena pairs yield temperatures between 163 and 218 degrees C, in good agreement with the 187-207 degrees C estimated by the Ga/Ge-sphalerite geothermometer. The ore sulphide was leached by the hydrothermal solution from diagenetic pyrite in the host rocks and disseminated sphalerite and galena in Cambrian carbonates

Jun 19, 1905

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

By B. M. England, L. C. Mackey

Magnesia minerals are included in most iron ore sinter mixes to provide the MgO requirements of blast furnace slag. The properties of these minerals have an influence on the eventual sintering properties of the mixes. A detailed study was undertaken of serpentine and dolomite and the use of limestone, olivine and magnesite was also investigated. A consideration of particle properties indicated that as these materials calcine a reduction in size can occur together with cracking and changes in surface properties. These changes could affect the permeability of the sintering bed and sintering performance. Studies of sintering reactions showed that magnesium and calcium, formed from the calcination of dolomite, are extremely mobile before the formation of melt. Evidence suggests that the movement of these oxides into surrounding areas is via a solid-state diffusion process. The diffusion of Ca into the surrounding hematite particles is faster than that of Mg, resulting in the formation of dicalcium ferrite and magnetite or magnesioferrite, the last two subsequently being converted to dicalcium ferrite in the presence of Ca with removal of Mg from the structure as ferroan periclase. Studies of pilot-plant sinters indicated that reaction mechanisms formulated from the bench-scale studies were occurring in actual sintering processes. The differences in sintering reactions between dolomite and serpentine were considered to be the major cause of differences in the availability of lime for bonding phase formation. Pilot-scale studies indicated that the sintering properties of a mix containing dolomite could be improved by increasing the basicity of the sinter mix while keeping the MgO level constant

Jun 18, 1905

By J. S. Duval

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The compilation of the National Uranium Resource Evaluation aerial gamma-ray data to produce maps of the apparent surface concentrations of potassium, uranium and thorium for the conterminous USA has resulted in a reasonably accurate representation of the distribution of these elements in the surface rocks and soils. This claim is supported by the general agreement between the mapped geology and the patterns seen in the data

Jul 1, 1991

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

By S. L. R. Lenharo, H. Kahn, H. Born

Different ore types result from the irregular spatial distribution of the associated alkaline/carbonatite rocks and the zoned alteration profile within which apatite may have undergone reprecipitation. Different flotation responses are caused by their mineralogy, iron oxide impregnation and grain-size characteristics. Samples from seven deposits were crushed, screened and separated before being studied by chemical analysis, optical microscopy, X-ray diffraction, FTIR spectroscopy, cathodoluminescence and scanning electron microscopy. Two main apatite varieties with peculiar crystal morphology were identified: hydroxy-fluorapatite as the primary phase and carbonate-fluorapatite as the reprecipitated phase. The former occurs as prismatic or ovoid grains and the latter as polycrystalline aggregates or crusts on the primary grains; both are associated with iron oxide coatings (primary) or intergrowths (secondary). Microflotation tests showed variations in flotability for particular apatite associations as well as intensity of iron oxide coatings. The differences in flotation behaviour can be related to morphological properties and chemical substitution in the apatite structure

Aug 1, 1996

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By P. S. Heyns, M. Heyns

A computer model has been developed of mine hoisting systems in deep South African gold mines. Particular attention was paid to the contribution of different modelling assumptions for the guides and guide-roller assemblies. Objective functions indicative of guide-roller tyre endurance, slipper-plate forces and perceived vibration levels were introduced to quantify dynamic performance. These objective functions were used to compare models. It was found that the choice of guide and guide-roller models did not influence the forces on the guide rollers significantly for typical shaft and conveyance characteristics at typical levels of viscous damping coefficients. The rigid and finite-element guide models gave the same results as those of the effective-stiffness guide model, and while the latter is suitable for simulation for design purposes, the finite-element model should be used for unusual guide geometries

Jun 19, 1905

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875