Search Documents

By A. J. Beer, A. Wetherelt

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. Camborne School of Mines has developed a simple, cost-effective light-sectioning method that has been used successfully in tunnels and small stopes. Light sectioning provides an almost visual examination of the stope's excavated profile. An illuminated section of walls, roof and floor is recorded photographically. Overbreak and underbreak can then be easily quantified by reference to the designed shape. The prototype rig is described. Use of a fish-eye lens to capture a greater field of view is discussed. Calibration was achieved by comparison with images made with a conventional wide-angle lens with nominal distortion. The system is reliable under a range of operating conditions including dust, heat and humidity. It is also simple and easy to use, does not require skilled personnel and is low cost

Jun 18, 1905

By H. B. Bell, L. C. Smith

Measurements have been made of the activity of 'FeO' in 'Fe0'-Mn0-Ti02 melts at 1475 degrees C. The results obtained are discussed in terms of ideal mixing of titanates and in terms of a regular solution model. On the basis of the regular solution model activities of Ti02 and MnO in the Fe0-Mn0-Ti02 and Mn0-Ti02 systems have been derived. The data have been shown to be consistent with the liquidus lines in the phase systems. Examples are given of the application of the data to slag-metal equilibria, being used to derive slag-metal data between liquid iron and Fe0-Mn0-Ti02 slags

Dec 1, 1971

By K. M. Kinealy, A. R. Ramsden, D. H. French

A negative correlation exists between sphalerite composition and gold content when gold is transported as Au(HS)2(-); however, there are spatial and temporal differences within a single deposit. A previous model for the formation of volcanogenic massive-sulphide deposits within thermally intensifying and waning hydrothermal sytems in much the same way as is observed around modern sea-floor vents is supported. The results also emphasise that recognition of the mechanisms of gold transport in ancient deposits depends critically on an understanding of their mineralogy and stratigraphy

Jan 1, 1991

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By G. Mellgren, O. Mellgren

The conductivity of a solution is often used industrially to control the salt concentrations of reacting systems, normally using electrodes made of glass fitted with platinised platinum electrodes. When a standard platinum conductivity electrode was used to control the acid fed to the leaching circuit for an ilmenite flotation concentrate at Titania, Norway, a deposit of calcium sulphate (containing some calcium phosphate) covered both the platinum electrode and the external glass fitting, rendering the electrode inefficient in the course of a few minutes. A new electrode consisting of a casing, two measuring tubes and an electrode stem is described and illustrated. A significant advantage of its design is that the useful range of conductivity measurement can be adjusted by adjusting the concentration of the electrolyte in the electrode. It has been in use at Titania for about four years with an electrolyte consisting of 0-1 n HCI. It is robust and demands little maintenance.

Dec 1, 1971

By R. W. Ruddle

"Besides copper, iron, silicon, and oxygen, a large number of elements may be present in copper ores, the more important of which are zinc, lead, arsenic, antimony, bismuth, selenium, tellurium, nickel, cobalt and the precious metals; impurities of less importance are calcium, magnesium, aluminium, barium, sodium, potassium, manganese, lithium, fluorine, titanium, uranium, vanadium, tin and molybdenum. All of these elements are eliminated to some degree in the subsequent roasting, smelting and converting operations.Information on the elimination of impurities during the smelting of copper is surprisingly meagre, however, rather more information is available on impurity removal during the smelting of the ore in reverberatory or blast furnaces."

Jan 1, 1953

By D. R. Wardrop, P. J. Rowsell, M. D. Waller

D.R. Wardrop agrees that artificial intelligence can contribute significantly to a reduction in both unit and overall well drilling costs but argues for human input to be allowed to overcome the differences encountered on striking the reservoir

Aug 1, 1995

By NA NA

Reports of discussion at sessions held in Keyworth, UK, on 22-23 April 1992.

Jan 12, 1992

By G. R. Doughty

It is shown that sodium can be removed very readily from molten aluminium by the use of a beta"-alumina, the more highly conducting form of beta-alumina, provided that the surface of the tube is wetted by a layer of salt. From current/time plots the theoretical amount of sodium removed has been calculated and excellent agreement obtained. The beta"-alumina tubes can be immersed directly in the Al without fracturing if they are pre-heated for a few minutes prior to immersion. According to its stability beta"-alumina should be attacked by molten Al at low Na contents, but in these experiments the salt acted as a protective layer. Magnesium chloride is a relatively cheap salt, whose Mg product can be used within a foundry. The only other product is NaCl, which can be used in-house as a flux or sent for disposal. No polluting gases are used or produced and no drosses created. The time for removal of sodium was quite short, comparable to that for chlorination

Jun 21, 1905

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By R. Immele-Meziou, G. J. Long, D. G. C. Robertson, O. A. Pringle

The reduction of naturally weathered ilmenite concentrate occurs in two steps: reduction of Fe3+ to Fe2+, followed by reduction of Fe2+ to Fe. Small amounts of a magnetic phase were also observed and may correspond either to an Fe3O4-FeTiO3 ilmenite phase or to an Fe3O4-Fe2TiO4 spinel phase. The total amount of metallic iron produced after 12 hr was only 50% of the total iron present in the sample.

Jan 4, 1992

By P. Rama Krishna, B. Narasimha Rao, P. Ali i Peera

Induced polarisation (IP) surveys are commonly used in uranium exploration programmes in India. The IP method is effective in detecting the disseminated metallic sulphides that are often associated with uranium minerals. However, conductive and polarisable host rock or overburden often introduces inductive or electromagnetic (EM) coupling into time domain IP measurements. This makes it difficult to distinguish between responses due to such coupling and those that might indicate economic mineralisation. Attempts must be made to remove the EM effects before the IP technique is used in drilling programmes. Transient decay curves which were recorded during field surveys at Pisnari were factorised using the Marquardt algorithm. Dispersion plots of the amplitudes and relaxation times of the composite exponential function enable a clear distinction to be made between the effects of EM coupling and those of mineralisation.

Jan 4, 1993

By J. R. Budden, P. A. Spencer, J. Barrett

The initially produced arsenic (III) is very toxic to the unconditioned culture but the mixed culture has the capacity to oxidise it to arsenic (V) in the presence of iron (III). It was possible to build up the resistance of the culture through progressive sub-culturing on arseno-pyrite until it could tolerate steady-state concentrations of 30 mM arsenic (III) and 200 mM arsenic (V). With some samples tested in the continuous systems the final arsenic concentrations reached 330 mM. It proved possible to use the laboratory batch data to establish the optimum operating conditions for continuous test systems with capacities of up to 32 m3. Data on the residence time, oxygen uptake rates and gold extraction from the bio-oxidised residues could then be confirmed by continuous testing without the need first to use empirical means to determine optimum conditions for continuous bio-oxidation. The data on residence time, oxygen uptake rate, solids density and neutralisation could be used to estimate the capital and operating costs of treating any given tonnage of the concentrate of interest. It was established that the arsenopyrite concentrates can be suitably bio-oxidised to cause the liberation of at least 90% of the gold content. The method is simple to operate and is flexible over a wide range of external conditions

Apr 1, 1991

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By T. D. Jones

Describes the facilities in South Wales for routine control and research work on all the various aspects of the dust problem. Considers mining and medical research, inspection and control, education, and plans for the future.

Jan 1, 1947

By R. P. Foster, ed.

The short selection of papers in the special issue provides an insight into the level of exploration activity in Africa and the science and technology that are underpinning it. A country-by-country survey is followed by discussion of geochemical exploration in tropical soils, the Liptako region of Niger, structural styles of deposits in Zimbabwe's Bulawayo-Bubi greenstone belt, structural controls in Zimbabwe's Eldorado shear zone, the regional framework for deposits in the Odzi-Mutare-Manica greenstone belt of Zimbabwe and Mozambique, and the Iperindo deposit in Nigeria's Ilesha schist belt

Apr 1, 1996

For the convenience of those who are unfamilar with thermodynamics, the following brief description and explanation is given of the thermodynamical terms and methods used in this book. It must, however, be strongly emphasized that the account given below is not an introduction to chemical thermodynamics; its sole purpose is to give the reader a rough understanding of the methods used in the earlier chapters. For further information, reference must be made to the standard textbooks on chemical thermodynamics by Glasstone.

Jan 1, 1953

By G. H. Blackwell

Sequences in open pit mining must be planned and regularly revised to incorporate changes in the variables which affect profitability. Interactive computer planning with colour graphic facilities is an effective tool for this purpose in the short and medium term. An interactive computer planning system for medium-size, low grade porphyry copper-molybdenum open pits is described. The planning system proved especially valuable during the critical stages of pushback mining when deep, inner pit ore was nearly depleted and the erratic grades of the next pushback provided ore and marginal material at a time of depressed metal prices.

Jan 8, 1993

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By P Shead, M A. Tuck

Both climate and methane control have been a prime concern in the development of the workings within the Deep Soft seam at Harworth Colliery. This paper describes the numerous methods employed over the past 15 years to effect control over these two major environmental pollutants at Harworth and describes a future method of working which will enable the output levels required to be achieved, whilst effecting the required level of both climatic and methane control. Firstly, the paper gives a broad historical overview of the steps taken since 1981, when production started in the Deep Soft seam at Harworth Colliery, to effect control over the main environmental pollutants in the seam. Secondly, the paper details the results of planning exercises undertaken to assess the various options with respect to panel layout, to achieve environmental control in future production districts. Finally, the recommended method of panel design to achieve the levels of production required is detailed.

Jan 7, 1997